Viking K-1770-3 Bedienungsanleitung

Viking Zugangskontrollsystem K-1770-3

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Viking K-1770-3 (8 Seiten) in der Kategorie Zugangskontrollsystem. Dieser Bedienungsanleitung war für 9 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Download PDF

Seite 1/8

Vandal Resistant Entry Phones with Built-In

Keypad and 125KHz Proximity Card Reader

The K-1770-3 Series entry phones provide a tough and

attractive handsfree phone for commercial, apartment, and

residential door entry or applications requiring a vandal

resistant speaker phone with built-in 125 KHz Proximity Card

Reader. The card reader outputs industry standard 26-bit

Wiegand data, allowing it to be used with a doorViking ES-1

controller or any controller compatible with 26-bit Wiegand

format. The K-1770-3 Series entry phones are available in

two attractive finishes: “brushed stainless steel” and “oil

rubbed bronze”.

When the “Call” button is pressed, the returns dialK-1770-3

tone. The keypad may then be used to dial any number. If

no Touch Tone is entered within 8 seconds, CPC is detected,

a busy signal is detected, or the programmable maximum call

time has elapsed, the will automatically disconnect.K-1770-3

Alternatively, the may be disconnected by pressingK-1770-3

the “Call” button again. The comes complete withK-1770-3

a standard, flush mount, rough-in box. In addition, an optional

VE-6x7 weather resistant, surface mount box is available (see

DOD 424).

The K-1770-3-EWP K-1770 shares all of the features of the -3

in addition to Enhanced Weather Protection (EWP) for outdoor

installations where the unit is exposed to precipitation or

condensation. EWP products feature foam rubber gaskets

and boots, sealed connections, gel-filled butt connectors, as

well as urethane or thermal plastic potted circuit boards with

internally sealed, field-adjustable trim pots and DIP switches

for easy on-site programming. For more info, see . DOD 859

K-1770-3

“Brushed Stainless Steel”

(similar to brushed nickel)

K-1770-3-BN

“Oil Rubbed Bronze”

(satin dark brown powder paint

with fine copper metallic)

Features

• Apartment entry phone when used with the Apartment Entry Dialer K-1900-3

or Apartment/Office Entry Controller or C-4000 C-3000 Apartment Entry

Controller

• Use with a to control 1 or 2 (expandable to 8) ( ) Viking C-500 DOD 177

K-1770’s and door/gate control on a single phone line

• Use with a to control 1 to 4 s and door/gate control Viking C-2000B K-177 0’

on a single phone line ( ) DOD 156

• Courtesy and customer assistance phone

• Automated teller (ATM) phone

• Use with a for proximity card reader door control Viking ES-1

• Provide unique front and back door chimes and paging when use with a

Viking SLP-1 SLP-4 C-2000Bor and

• Kiosk phone with (100 number speed dialing) when used with the K-1900-9

Multi-Number Dialer ( ) DOD 321

• Use with Viking’s Proximity Cards: , , PRX-C PRX-C-ISO PRX-FOB (DOD 198)

Entry Phone Power: Telephone line powered 20V DC/20mA minimum

Proximity Card Reader Power: 5 to 14V DC @ 60mA maximum

Dimensions: Overall: 5.5” x 6.5” x 2.6” (140mm x 165mm x 66mm),

Rough-in box: 4.5” x 5.5” x 2.5” (114mm x 140mm x 64mm)

Shipping Weight: 3.5 lbs (1.6 kg)

Environmental: -30°F to 150°F (-34°C to 65°C)

Humidity - K-1770-3: 5% to 95% non-condensing

Humidity - K-1770-3-EWP: Up to 100% condensing

Speaker Volume: Approximately 70 db maximum @1m

CPC Disconnect Time: 500ms minimum

REN #: 0.5 A

Connections: Gel-filled tip and ring connectors

Applications

Specifications

• Built-in 125KHz 26-bit Wiegand proximity card reader with LED,

beep card read confirmation, and EWP board protection

• Compatible with the following Viking Proximity Cards and Fobs:

PRX-C PRX-C-ISO PRX-FOB (DOD 198), and

• Vandal Resistant Features: 14 gauge louvered 316 stainless

steel faceplate with permanent laser etched graphics, stainless

steel “Call” button, heavy duty metal keypad and T-10 Torx

security mounting screws, scratch resistant powder coating

(K-1770-3-BN)

• Marine grade 316 stainless steel Weather Resistant Features:

faceplate, screws and and push button switch. Switch internally

sealed per IP67. Mylar speaker. Self-draining mic mount.

Faceplate, mic and speaker gaskets. Weather Resisant powder

paint (K-1770-3-BN)

• is designed to meet IP66 Ingress Protection K-1770 -3-EWP

Rating (see for more information) DOD 859

• Available in 2 standard faceplate finishes: 316 brushed stainless

steel or oil rubbed bronze powder paint

• Blue “in use” LED

• Telephone line powered

• Volume adjustments for microphone and speaker

• Advanced call progress detection: disconnects on busy signal,

return to dial tone, CPC, reorder tone, maximum call time out and

40 second silence time out

• Selectable auto-answer feature for monitoring

• Selectable push button disconnect

• Zinc plated steel rough-in box with (2) 3/4” conduit knockouts

• Optional Surface Mount Box available ( ) VE-6x7 DOD 424

• Optional to illuminate the front panel at night (VE-LIGHT DOD 428)

DESIGNED, MANUFACTURED AND SUPPORTED IN THE USA

K-1770-3 Series

Entry Phones with Keypads

and Proximity Card Readers

September 29, 2023

PRODUCT

MANUAL

SECURITY & COMMUNICATION

VIKING

Optional Instruction Label (included):

Clean surface and adhere label when

using a K-1770-3 with a K-1900-3

Apartment Entry Dialer.

(4) 6-32 X 3/4”

Stainless steel,

flat head, T-10

Torx security

screws (included)

(1) .74”

diameter Rear View of

the Optional

VE-6x7 Surface

Mount Box

3.0” 3.3”

3.0”

2.25”

Condensation

Drain Hole

5.64”

6.72” 3.25”

(2) 0.2 x 0.43 slots

Optional VE-6x7

Surface Mount Box

(not included)

The optional VE-6x7 Surface Mount Box (above) is designed

to be surface mounted to a single gang box, double gang box,

or VE-GNP Gooseneck Pedestal (shown right). For more

information on the VE-6x7 VE-GNPand , see DOD 424.

Peel paper liner and adhere gasket to back of

panel, centering over mounting holes. Caution:

For rough surfaces (ie: brick, stucco, etc.)

additional caulking may be required.

4.5”

2.5”

3/4” Conduit

Knockouts

5.5”

Rough-In

Box

(included)

(4) 0.38” diameter

K-1705-3-EWP

shown with VE-6x7

Surface Mount Box

and VE-GNP

Gooseneck

Pedestal

(not included)

VIK IN G

DE F

JKL

MN O

TUV

WXY

OPE R

ress "Ca

ll"b utt o

th en

en t er ten

t code

Features Overview

Push Button Switch: Push to

initiate call, push again to

disconnect. Solid 316 stainless

steel internally sealed per IP67.

Speaker Screen: Speaker screen

with 0.018" diameter holes to prevent

punctures from paperclips, etc.

Faceplate Material: 14 gauge 316

stainless steel. The SS model has

a #4 brushed finish, the BN models

have a powder painted finish.

Speaker: Mylar speaker with

rubber gasket to maintain

water-tight seal and eliminate water

deterioration.

Blue Call LED: Flashes during

dialing, then lights steady when

answered.

Microphone: Omni-directional

microphone with protective

water-resistant cloth.

Condensation Drain Hole

Mounting Screws: (4) 6-32 X 3/4”

Marine grade 316 stainless steel,

flat head, T-10 Torx security screws

and drive bit (included)

Laser Etched Graphics: For long

lasting easy to read graphics.

(copper metallic lettering on model

K-1770-BN-3)

Proximity Card Reader: 26-bit

Wiegand, 125KHz, red LED turns

off and transducer will beep during

card read. Fully potted EWP. Read

range 1.25" to 2.0". Impact resistant

polycarbonate lens with water-tight

gasket.

ABC

JKL

TUV

OPER

GHI

PRS

DEF

MNO

WXY

VIKING

VIKINGVIKING

Power: 5 to 14V DC @ 60mA maximum

Maximum Cable Length: 500 ft 24 Awg stranded shielded

(Belden 9537)

Frequency: 125KHz

Format: 26 bit Wiegand

Read Range: 1.25” to 2.0”

Technologies Supported: Viking , PRX-C PRX-C-ISO,

PRX-FOB, certain legacy HID® proximity protocols* and

certain AWID 125Khz proximity protocols**

Transducer: Beeps during card read

LED: Red, turns off during card read

Humidity: Up to 100% (fully potted EWP)

Operating Temperature: -34° C to 65° C (-30° F to 150° F)

* HID and the HID logo are registered trademarks of HID

Global Corporation, an ASSA ABLOY company. All other

trademarks are the property of their respective owners.

** AWID is a trademark of Applied Wireless Identification Group.

Proximity Card Reader Specifications

Installation

A. Mounting

VIKING

Mode l:

XXXXXX

Se rial No : XXXXX XXX

Viking Electronics , Inc. (715) 3 86- 88611531 Industrial St., Hudson, WI 54016

P/N: DEV: RoHS

5.5”

4.04”

6.5”

5.12”

* C.O. Line or Analog

PABX/KSU Station

Spade

Terminal

(included)

*** Earth

Ground

(optional)

Red

(Ring)

Green

(Tip)

Rear View of

the K-1770-3

** Gel-Filled

Connectors

(included)

B. Wiring the K-1770-3 Phone

** Note: The gel-filled (water-tight) butt connectors are designed for insulation displacement on 19-26 gauge

wire with a maximum insulation of 0.082 inches. Cut off stripped wire ends prior to terminating.

*** Note: To increase surge protection, loosen the PCB

mounting screw labeled (shown right) and fasten a wire

with spade terminal (included) from the mounting screw to

Earth Ground (grounding rod, water pipe, etc.)

* Note: When installing a line powered phone on a low

voltage and/or low loop current phone system extension, a

TBB-1B Talk Battery Booster may be required ( .DOD 632)

Model DOD# Description

C-500 177 Advanced 2 Door Controller (see page 5)

C-2000B 156 Advanced 4 Door/Gate Controller (see page 6)

C-3000 162 Multi-Tenant Entry System (see page 7)

C-4000 164 Apartment/Office Entry Controller (page 7)

K-1900-3 312 Apartment Entry Dialer (see page 6)

To Optional Viking Entry Controllers (not included)

C. Wiring the K-1770-3 Proximity Card Reader

VIKING

Mod e l:

XXXXXX

Ser ial No: XXXXXXXX

Viki ng Ele ctr oni cs, I nc. (715) 386-886 1

1531 In dus tr ial St ., Hud so n, WI 54016

P/N: DEV: R oHS

Back View of

the K-1770-3

White (Data 1)

Green (Date 0)

- Black (GND)

+ Red (5-14VD) * Up to 500 ft

3-Wire Gel-Filled Butt Connectors

included (3M Scotchlok UR2)

24 Awg Stranded

Shielded Cable

(Belden 9537)

White

Green

Black

Red

Black

Red

Green

White

To Viking model

ES-1 (shown)

C-4000 (page 7)

or equivalent 26-Bit

Wiegand Card

Reader Controller

Viking Model ES-1 (not included,

see DOD 193 for more information)

Touch Tone

Programming Phone

(not included)

RAD-1A Remote Access

Device (not included,

see DOD 410)

Remote Touch Tone

Programming Phone

(not included)

VIKING

ELECTRONICS

HUDSON, WI 54016

STAND ALONE

DOOR CONTROLLER

ENTRY SYSTEM

POWER 12V DC

MODEL ES-1

POWER

PROGRAM

PHONE

LOG

BUS

2 3 4 5

GANG

PROG

6789

WI EGAND

DEVICE

10 11

DOOR

STRIKE

N.O.

COM

N.C.

BLK

RED

GRN

WHT

Doorstrike

Power Supply

12-24V AC or DC

Doorstrike

12V DC

Adapter

(included

with ES-1)

Share power with

12-24V AC/DC door

strike with 200mA

available current or use

the included 12V DC

adapter.

IMPORTANT: Electronic devices are susceptible to lightning and power station electrical surges from

both the AC outlet and the telephone line. It is recommended that a surge protector be installed to protect

against such surges.

Produktspezifikationen

Marke:	Viking
Kategorie:	Zugangskontrollsystem
Modell:	K-1770-3
Breite:	165 mm
Tiefe:	66 mm
Produktfarbe:	Gebürsteter Stahl
Internationale Schutzart (IP-Code):	IP67
Übertragungstechnik:	Kabelgebunden
Höhe:	140 mm
Platzierung:	Wand
Eingebautes Display:	Nein
Betriebstemperatur:	-34 - 65 °C
Relative Luftfeuchtigkeit in Betrieb:	0 - 95 %
Paketgewicht:	1600 g
Zertifizierung:	FCC Part 68\nFCC Part 15
Typ:	Intelligenter Zugangskontrollenleser
Gehäusematerial:	Edelstahl
Energieverbrauch:	20 mA
Geräuschpegel:	90 dB
Kamera enthalten:	Ja
Knopfanzahl:	13
Menge Außengeräte:	1
Einfache Installation:	Ja
einegbaute Tastatur:	Ja
Tastatur Anzahl der Tasten:	12
Autentifizierungstyp:	Access chip/card, Password
Zugriffschip/Kartenleser:	Ja
Zugriffscodeleser:	Ja