Velleman K8200 Bedienungsanleitung
Velleman
3D Printer
K8200
Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Velleman K8200 (16 Seiten) in der Kategorie 3D Printer. Dieser Bedienungsanleitung war für 5 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet
Seite 1/16
![](https://manualstech.ams3.cdn.digitaloceanspaces.com/html/nl/velleman/k8200/html/bg1.png)
English
.....................................................................
2
Nederlands
.............................................................
5
Français
...................................................................
8
Deutsch
...................................................................
11
Espanõl
....................................................................
14
![](https://manualstech.ams3.cdn.digitaloceanspaces.com/html/nl/velleman/k8200/html/bg2.png)
- 2 -
VELLEMAN-KIT
3D Printer kit
Order code: K8200
manufactured by:
VELLEMAN NV.
Legen Heirweg, 33
9890 Gavere
Belgium
CE conformity information:
The K8200 is a DIY 3D printer kit, it contains all the bits and pieces to construct your own 3D printer but does not contain
additional protection.
As it is a kit and not a nished product, compliance with the CE regulations depends on the build-quality; also the following
notes must be taken into account.
Conductive EMC towards the public distribution network is not an issue as this is related to the power supply.
Radiated EMC depends substantially on the build quality, it might be required to add shielding but this cannot be predicted.
A built K8200 should comply with EN50081 normation
Electromagnetic radiation (EMC):
The included power supply meets all the applicable European requirements and bears the CE-mark.
It is protected against overload and short circuit and nothing needs to be modied. The working voltage of the 3D printer is
15Vdc (extra low voltage) and therefore it’s outside the scope of the Low voltage directive.
Always unplug before maintenance or modication.
Electrical safety:
!
Important safety instructions
![](https://manualstech.ams3.cdn.digitaloceanspaces.com/html/nl/velleman/k8200/html/bg3.png)
The 3D printer contains a lot of moving parts, but the force of the stepper motors is too low to cause serious injuries. Never-
theless it is recommended to provide additional protection against mechanical risks.
The easiest way to make your 3D printer “accident proof” is to put it inside a protective enclosure which completely covers
the 3D printer – with or without an access door and fume extraction. (numerous designs can be found on the internet)
To make it extra safe a switch which interrupts the power supply of the printer when the enclosure or door is opened can be
added. It is also advisable to install an external emergency stop switch, which also cuts off the power supply.
Providing adequate protection is the responsibility of the assembler.
Always cut power before maintenance or modication.
Mechanical safety and protection:
!
The 3D printer is not intended for use by persons (including children) with reduced physical, or mental capabilities,
or lack of experience and knowledge, unless they have been given supervision or instruction concerning the use of
the appliance by a person responsible for their safety
Children should be supervised to ensure that they do not play with the appliance.
The above information is believed to be correct but does not purport to be all inclusive and shall be used only as a guide.
The information in this document was obtained from sources which we believe are reliable.
However, the information is provided without any warranty, express or implied, regarding its correctness.
The conditions or methods used for assembling, handing, storage, use or disposal of the device are beyond our control and
may be beyond our knowledge. For this and other reasons, we do not assume responsibility and expressly disclaim liability
for loss, injuries, damage, or expense arising out of or in any way connected with the assembly, handling, storage, use or
disposal of the product.
General safety information:
There is a potential risk of burns as the Printer head (extruder) can reach up to 270°C.
The use of common sense should be sufcient to prevent burns, but in some environments it is highly recommended to
provide additional protection. (see § Mechanical safety and protection)
The max. temperature of the heated bed is 60°C, this is below the 1 min. burn threshold for plastic surfaces according to
CENELEC Guide 29. Normal reexes prevent long contact periods with hot surfaces
Always let the 3D printer cool down for 60 min. before maintenance or modication.
Risk of burns:
!
This printer is designed for use with PLA and ABS lament (MSDS for the Velleman lament is available).
PLA: is a safe and non-toxic material, there are no known health safety risks when used in 3D printers.
ABS: when printing with ABS there is a distinctive ‘burned plastic’ smell. This is quite normal but it may also cause head-
aches, respiratory- and eye irritation with sensitive people (although it is not toxic)
Only use the printer in a well-ventilated area, if printing with ABS it is advisable to add a fume hood (with active car-
bon ltering for ductless extraction). Fume extraction is mandatory for use in ofces, classrooms and alike.
Never burn printer lament, toxic gasses and vapors will be generated if exposed to re.
Health:
!
- 3 -
Produktspezifikationen
Marke: | Velleman |
Kategorie: | 3D Printer |
Modell: | K8200 |
Brauchst du Hilfe?
Wenn Sie Hilfe mit Velleman K8200 benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten
Bedienungsanleitung 3D Printer Velleman
![Velleman](/images/pdf_free.png)
13 Juli 2024
Bedienungsanleitung 3D Printer
- 3D Printer Anker
- 3D Printer Polaroid
- 3D Printer CraftBot
- 3D Printer Flashforge
- 3D Printer Monoprice
- 3D Printer Sindoh
- 3D Printer Bq
- 3D Printer MakerBot
- 3D Printer XYZprinting
- 3D Printer Wasp
- 3D Printer Anycubic
- 3D Printer Creality3D
- 3D Printer Wanhao
Neueste Bedienungsanleitung für -Kategorien-
![Wasp](/images/pdf_free.png)
5 September 2024
![MakerBot](/images/pdf_free.png)
3 September 2024
![MakerBot](/images/pdf_free.png)
3 September 2024
![CraftBot](/images/pdf_free.png)
2 September 2024
![Anker](/images/pdf_free.png)
28 August 2024
![Anycubic](/images/pdf_free.png)
24 August 2024
![Sindoh](/images/pdf_free.png)
24 August 2024
![Flashforge](/images/pdf_free.png)
22 August 2024
![Anycubic](/images/pdf_free.png)
20 August 2024
![Monoprice](/images/pdf_free.png)
19 August 2024