Velleman ET20 Bedienungsanleitung

Velleman Heizung ET20

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Velleman ET20 (12 Seiten) in der Kategorie Heizung. Dieser Bedienungsanleitung war für 17 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Download PDF

Seite 1/12

ET20

ETCHING TANK WITH AGITATOR AND HEATER

ETSTANK MET VERWARMINGSELEMENT EN POMP

GRAVEUSE VERTICALE AVEC POMPE ET RÉSISTANCE

GRABADOR CON BOMBA Y ELEMENTO CALENTADOR

ÄTZMASCHINE MIT PUMPE UND HEIZUNG

USER MANUAL 2

GEBRUIKERSHANDLEIDING 4

MODE D'EMPLOI 5

MANUAL DEL USUAR 7IO

BEDIENUNGSANLEITUNG 9

ET20

V. 03 17/02/2016 2 ©Velleman nv –

USER MANUAL

1. Introduction

To all residents of the European Union

Important environmental information about this product

This symbol on the device or the package indicates that disposal of the device after its lifecycle could

harm the environment. Do not dispose of the unit (or batteries) as unsorted municipal waste; it

should be taken to a specialized company for recycling. This device should be returned to your

distributor or to a local recycling service. Respect the local environmental rules.

If in doubt, contact your local waste disposal authorities.

Thank you for choosing Velleman! Please read the manual thoroughly before bringing this device into service. If

the device was damaged in transit, don't install or use it and contact your dealer.

Check first if you have all the pieces: the air pump and its tube, the heater with thermostat and the [1] [5]

tank, consisting of the tank itself , 2 tank support pieces , and 3 fixation clips and wires . Refer [3] [2] [7] [6]

to the illustration on page 2 of this manual.

2. Safety Instructions

Keep this device away from children and unauthorized users.

WARNING: this tank must be filled with an etching solution (not included), e.g.

ammonium persulfate, hydrochloric acid or ferric chloride. These products are toxic and

(highly) corrosive. Do not inhale vapours. Avoid eye or skin contact at all times.

Dispose of etching liquid in accordance with local regulations. pour etching liquid Never

into the sewers.

3. General Guidelines

Refer to the on the last pages of this manual. Velleman® Service and Quality Warranty

Indoor use only. Keep this device away from rain, moisture, splashing and dripping liquids.

Never put objects filled with liquids on top of or close to the device.

ET20

V. 03 17/02/2016 3 ©Velleman nv –

Keep this device away from dust and extreme temperatures.

Protect this device from shocks and abuse. Avoid brute force when operating the device.

 Familiarise yourself with the functions of the device before actually using it.

 All modifications of the device are forbidden for safety reasons. Damage caused by user modifications to

the device is not covered by the warranty.

 Only use the device for its intended purpose. Using the device in an unauthorised way will void the warranty.

 Damage caused by disregard of certain guidelines in this manual is not covered by the warranty and the

dealer will not accept responsibility for any ensuing defects or problems.

 Keep this manual for future reference.

4. Assembly

Refer to the illustrations on page 2 of this manual.

1. First, fill the tank [3] with water and check for leaks. If no leaks are found, remove the water from the tank.

2. One of the air inlets on the tank is sealed.

Connect the air pump to the free air inlet by means of the plastic tube. [1]

3. Fit the heater (spare part order code ET200) at the side opposite the air inlet. The heater is pre-[5]

regulated and set for a temperature of approx. °C, the optimal temperature for ferric chloride treatment. 32

4. Carefully tighten the clamping screw.

5. Install the support pieces [2] in the tank’s grooves.

The etching tank is now ready to be used.

Safety Warning

You should only remove the heater in exceptional circumstances, as it is not without danger. The glass of the

heater may crack under the influence of the difference in temperature when the warm heater comes into

contact with cold water. There is a genuine risk of electroshocks if this happens. Therefore, you should always

unplug the device and let the heater cool down before removing it. You should also make sure that your hands

are dry when you are connecting or disconnecting the device. Take care to use this device with the suitable

amount of etching solution.

5. Operation

1. Place the air pump higher than the liquid level in the tank to avoid flow-back. [1]

2. Fill the tank with the desired solution: use 2.25 L to fill the tank. : The red line on the heater Caution [4]

must always be covered liquid. in

3. Turn the heater on and let it heat up for 2 minutes.

4. Put the plastic clips on the printed board, and adjust the length of the fixation wires . Put the board [7] [6]

in the tank at ± 1 cm below the liquid surface.

5. Turn the air pump on to agitate the liquid. [1]

6. Monitor the evolution of the etching. You can place a lamp behind the tank; because the tank is

transparent, you can see what happens. At the correct temperature, etching takes about 4 minutes.

7. When finished, wash away any trace of the product under running water.

8. Finally, inspect the tracks of your etched circuit.

6. Technical Specifications

etching tank with pump and heater

300 W / 230 Vac

spare heater (not incl.)

order code ET200

dimensions

external

360 x 280 x 40 mm

internal

350 x 230 x 30 mm

tank capacity

2 L .5

Use this device with original accessories only. Velleman nv cannot be held responsible in the event

of damage or injury resulting from (incorrect) use of this device. For more info concerning this

product and the latest version of this manual, please visit our website www.velleman.eu. The

information in this manual is subject to change without prior notice.

The copyright to this manual is owned by Velleman nv. All worldwide rights reserved. No part of this

manual may be copied, reproduced, translated or reduced to any electronic medium or otherwise without the

prior written consent of the copyright holder.

Produktspezifikationen

Marke:	Velleman
Kategorie:	Heizung
Modell:	ET20
Breite:	350 mm
Tiefe:	30 mm
Produktfarbe:	Aluminium,Black
Höhe:	230 mm
AC Eingangsspannung:	230 V
AC Eingangsfrequenz:	50 Hz
Verpackungsbreite:	360 mm
Verpackungstiefe:	40 mm
Verpackungshöhe:	280 mm
Schnellaufheizung:	Ja
Typ:	Infrarot-Heizlüfter
Leistung:	300 W
Gehäusematerial:	Acrylonitrile styrene acrylate (ASA),Styrene Ethylene Butylene Styrene (SEBS)
Griff(e):	Ja
Heizleistung:	300 W
Geeignet für:	Indoor
Platzierungsoptionen:	Desk,Floor,Table,Window
Tragbar:	Ja
Wasserkapazität (Abschnitt):	2.5 l