VDO 190-903 Bedienungsanleitung

VDO Meetapparatuur 190-903

Lesen Sie kostenlos die ๐Ÿ“– deutsche Bedienungsanleitung fรผr VDO 190-903 (2 Seiten) in der Kategorie Meetapparatuur. Dieser Bedienungsanleitung war fรผr 3 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Download PDF
Seite 1/2
Ammeter
Installation Instructions
Instruction Sheet #0 515 012 154
Rev. 10/09
INSTRUCTIONS FOR THE INSTALLATION OF THE AMMETER ARE CONTAINED HEREIN.
USE IS RESTRICTED TO 12-VOLT NEGATIVE GROUND ELECTRICAL SYSTEMS. LIGHT
BULB, IF SUPPLIED, IS 12 VOLT.
S i e m VDO
Tools and Materials Needed For Installation:
10 Gauge stranded, insulated wire
Ring terminals
Non-insulated ยผ" spade connectors
2ยนโ„โ‚โ‚†" hole saw
Drill and drill bit set
Half-round file
Tape measure or ruler
Small tools: wrench or nut driver, utility
knife, pliers, etc.
Ammeter Installation:
To Begin, go to #โžŠ
โžŠBEGIN HERE
1. Select the location where you will mount
the gauge, and mark a center point.
1. Run a series of wires from the ammeter
location through the firewall to:
a) the positive (+) terminal on
the alternator;
b) the positive (+) terminal on
the starter;
Wiring the Ammeter:
ร™
[text continues at # ร‹]
The bezel diameter is only a few mil-
limeters larger than the gauge itself.
With that in mind, measure and pre-
cisely mark the gauge location be-
fore cutting any holes!
CAUTION!!!
2. Cut a 2ยนโ„โ‚โ‚†" (52 mm) diameter hole for
the gauge. Make sure the hole is no larger
than 2 ยนโ„โ‚โ‚†" (52 mm). If the gauge is too
snug, use a file to slightly enlarge the open-
ing. (Diagram A)
3. Slip the mounting bracket over the
mounting bolts on the back of the gauge.
Screw on the accompanying nuts. Tighten
the nuts until the ammeter can no longer
be rotated by hand. (Diagram B)
DO NOT OVERTIGHTEN.
Item Description Quantity
1. Ammeter (2 ยนโ„โ‚โ‚†" [52 mm] diameter) 1
2. Lamp Socket (Push in, wedge-type) 1
3. Light Bulb (12-volt / G.E. #158 or equivalent) 1
4. VDO Mounting Bracket and nuts (2) 1
5. Installation Instructions 1
Parts List
Diagram D
Proper wiring of the VDO Ammeter
๎˜‚/ ๎˜‚%
9W^YdY_^๎˜ˆ๎˜‰CgYdSXUT๎˜ˆ๎˜!"f๎˜”
<_QT
CdQbdUb1\dUb^Qd_b 7b_e^T
2QddUbi
1]]UdUb 6ecU๎˜ˆ2_h
<YWXd
CgYdSX
Note: We recommend this instrument be
installed by a trained professional.
CAUTION:
Read these instructions
thoroughly before making installation.
Do not deviate from assembly or wiring
instructions. Always disconnect battery
ground before making any electrical
connections. If in doubt, please contact
your dealer or VDO at 1-800-265-1818.
โž‹CONTINUE HERE
Diagram A
Gauge dimensions
Diagram B
Proper mounting of the VDO Ammeter
c) the positive (+) terminal on
the ignition switch.
2. Connect the wires from the alternator,
starter and ignition to the terminals on the
back of the ammeter as shown in Diagram
C.
At this point, the installation and wiring
of your ammeter is complete. Turn on the
ignition and start the engine to be sure the
ammeter is working properly. If it isn๎˜ฏt, re-
check your wiring.
3. Connect the wire from the light switch
(after the fuse box) and from a ground lo-
cation to the ammeter light switch termi-
nals, also as shown in Diagram C.
PD[๎˜… ๎˜†๎˜…๎˜‡๎˜ˆ ๎˜‰๎˜Š๎˜† PP๎˜‹
๎˜Š๎˜…๎˜Œ๎˜ˆ ๎˜‰๎˜๎˜‡ PP๎˜‹
๎˜Š รฉ๎˜ˆ ๎˜‰๎˜๎˜ PP๎˜‹
๎˜Š ๎˜ˆ ๎˜‰๎˜๎˜Š PP๎˜‹
๎˜‘๎˜‘๎˜
๎˜Š ๎˜ˆ ๎˜‰๎˜๎˜Š PP๎˜‹

Produktspezifikationen

Marke: VDO
Kategorie: Meetapparatuur
Modell: 190-903

Brauchst du Hilfe?

Wenn Sie Hilfe mit VDO 190-903 benรถtigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten


Bedienungsanleitung Meetapparatuur VDO

VDO

VDO 190-903 Bedienungsanleitung

18 August 2024

Bedienungsanleitung Meetapparatuur

Neueste Bedienungsanleitung fรผr -Kategorien-

Vemer

Vemer Energy-230 M Bedienungsanleitung

2 Oktober 2024
AkYtec

AkYtec SMI2-M Bedienungsanleitung

1 Oktober 2024
Eberle

Eberle LSW-3 Bedienungsanleitung

1 Oktober 2024
Hager

Hager EC360 Bedienungsanleitung

1 Oktober 2024
Technoline

Technoline MA 10230 Bedienungsanleitung

28 September 2024
Amprobe

Amprobe RS-3-PRO Bedienungsanleitung

26 September 2024
PeakTech

PeakTech 6191 Bedienungsanleitung

25 September 2024
PeakTech

PeakTech 6192 Bedienungsanleitung

25 September 2024
PeakTech

PeakTech 6194 Bedienungsanleitung

25 September 2024
PeakTech

PeakTech 6170 Bedienungsanleitung

25 September 2024