Vantec UGT-CR961 Bedienungsanleitung
Vantec
Geheugenkaartlezer
UGT-CR961
Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Vantec UGT-CR961 (4 Seiten) in der Kategorie Geheugenkaartlezer. Dieser Bedienungsanleitung war für 5 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet
Seite 1/4
Prepare your computer case for installation.
2. Locate an available 3.5” or 5.25” drive bay where you would like
to install the device.
3.
5.25” Drive Bay
3.5” Drive Bay
*Using Optional 3.5” to 5.25” Front Bay Converter Kit (HDA-525P) to install into a 5.25” Front Bay
Slide the front panel device into your case until the front panel
is flush with the front of your case.
1b. Secure the 5.25” front panel device to your computer case with
the provided screws.
2b. Proceed to connect the front panel device to your system’s
motherboard or expansion card.
3b.
Connect to
System 20 pin
USB 3.0 Header
Connect to
System Audio
port Header
Connect to
System SATA
port Header
Proceed to connect the front panel device to your system’s
motherboard or expansion card.
3a.
Secure the 3.5” front panel device to your computer case with
the provided screws.
2a.
Slide the front panel device into your case until the front panel
is flush with the front of your case.
1a.
3.5” Front Panel Installation
Connect to
System 20 pin
USB 3.0 Header
Connect to
System Audio
port Header
Connect to
System SATA
port Header
Installation Guide Guía de instalación Guide d'installation Installationsanleitung
Guida all’installazione 取り付けガイド 安裝指南 安装指南
Verify the package contents.
1.
3.5” Front Panel Device Installation Guide
Installation Screws
Secure with the screws provided by the 3.5” to 5.25” front panel
converter bracket.
3.
Slide in the 3.5” front panel device into the front bay converter kit
until the front panel is flush.
2.
Prepare the 3.5” to 5.25” front panel converter kit.
If you would like to mount your 3.5” device into your 5.25” drive bay, you may do so by using Vantec’s HDA-525P 3.5“ to 5.25” bay converters. Follow the steps below to convert your device form factor to 5.25”.
1.
Converting Your 3.5” Front Panel Device to 5.25” Form Factor
Make sure all connection are connected well and place the cover
back on to your case.
5. Drivers will be automatically detected and installed. Your device
will be ready for use.
6.
Copyright © 2012 Vantec Thermal Technologies. All Right Reserved. | All Registered Trademarks Belong To Their Respective Companies.
v1.01
Information in this document is subject to change without notice.
Reproduction of these materials in any manner whatsoever without written permission is strictly forbidden.
Printed in China
Printed on Recycled Paper.
Diagram shown is the USB 3.0 20-Pin found on supported motherboards or expansion cards. Please refer to your motherboard
manufacturer’s documentation for the location of these ports.
*
Connecting Your Front Panel Device
4.
SATA
SATA header on system
Note: Missing pin
and notch on the
connector matches
notch on the head
USB 3.0(20-pin*) header on system
Audio header
on system
Note: Missing pin
Connect to
System 20 pin
USB 3.0 Header
Connect to
System Audio
port Header
Connect to
System SATA
port Header
Supports all standard memory cards.
Produktspezifikationen
Marke: | Vantec |
Kategorie: | Geheugenkaartlezer |
Modell: | UGT-CR961 |
Brauchst du Hilfe?
Wenn Sie Hilfe mit Vantec UGT-CR961 benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten
Bedienungsanleitung Geheugenkaartlezer Vantec
5 September 2024
5 September 2024
5 September 2024
5 September 2024
5 September 2024
5 September 2024
5 September 2024
5 September 2024
Bedienungsanleitung Geheugenkaartlezer
- Geheugenkaartlezer Connect IT
- Geheugenkaartlezer Gembird
- Geheugenkaartlezer Hama
- Geheugenkaartlezer Manhattan
- Geheugenkaartlezer Nedis
- Geheugenkaartlezer Sandberg
- Geheugenkaartlezer Sony
- Geheugenkaartlezer Sweex
- Geheugenkaartlezer Trust
- Geheugenkaartlezer Buffalo
- Geheugenkaartlezer CSL
- Geheugenkaartlezer Eminent
- Geheugenkaartlezer König
- Geheugenkaartlezer Renkforce
- Geheugenkaartlezer Ewent
- Geheugenkaartlezer Goobay
- Geheugenkaartlezer Icy Box
- Geheugenkaartlezer NZXT
- Geheugenkaartlezer SilverStone
- Geheugenkaartlezer Conceptronic
- Geheugenkaartlezer Icidu
- Geheugenkaartlezer BlackBerry
- Geheugenkaartlezer Akasa
- Geheugenkaartlezer Speed-Link
- Geheugenkaartlezer Hikvision
- Geheugenkaartlezer Maxell
- Geheugenkaartlezer Sitecom
- Geheugenkaartlezer Siig
- Geheugenkaartlezer StarTech.com
- Geheugenkaartlezer Green House
- Geheugenkaartlezer Satechi
- Geheugenkaartlezer IC Intracom
- Geheugenkaartlezer Icy Dock
- Geheugenkaartlezer Rabobank
Neueste Bedienungsanleitung für -Kategorien-
6 September 2024
6 September 2024
4 September 2024
4 September 2024
4 September 2024
4 September 2024
4 September 2024
4 September 2024
4 September 2024
4 September 2024