US Blaster USB 7014 Bedienungsanleitung
US Blaster
DJ Party Musik
USB 7014
Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für US Blaster USB 7014 (55 Seiten) in der Kategorie DJ Party Musik. Dieser Bedienungsanleitung war für 13 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet
Seite 1/55
DESIGN BY U.S BLASTER - P.O. Box 5376 - Carefree - AZ 85377-USA.
OWNERS MANUAL
CONSOLE MIXERS
USB 7013 - 7014
DESIGN BY U.S BLASTER - P.O. Box 5376 - Carefree - AZ 85377-USA.
USB 7013 - 7014
Console mixers
GENERAL SAFETY INSTRUCTIONS
- Always read the user guide before using the equipment.
- Keep the user guide in a place where everyone can read it.
- Use the equipment indoors and not in humid environments.
- Never remove or insert a plug from or into a wall socket with wet hands.
- If the plug and/or cable and/or cable input of the equipment is damaged it must be repaired by
aprofessional.
- Always take the plug out of the wall socket in the event of a thunderstorm, and also when the
equipment is not being used for a while.
-Never remove the plug from the power socket by pulling on its cable.
- Install the equipment in such a way that sufficient cooling is possible.
- Never use the appliance in the vicinity of heat sources and/or in direct sunlight.
-Make sure that no small objects or liquids can get in to the appliance.
-Only clean the appliance with a slightly moist dust-free cloth. Do not use cleaning products or
solutions!
-The appliance contains no components, other than those mentioned in the user guide that can
be repaired or replaced by the user.
- If the appliance is defective, it must be repaired by a US Blaster qualified repairs company.
- Keep the equipment out of the reach of children.
Keep the packaging safe so that, if the equipment is defective, you can
send it back in its original packaging and so avoid any damage.
©US Blaster Europe BV
Do not carry out any repairs on the equipment yourself; doing so will invalidate the guarantee.
The equipment may also not be modified; doing so will also invalidate the guarantee.
The guarantee is also invalidated if accidents and damage of any form are caused as a result
of improper use and/or not heeding the warnings in general as laid out in this user guide.
US Blaster Europe accepts no responsibility for any personal accidents as a consequence of not
following the safety instructions and warnings. This is also the case for consequential loss in
any form.
DESIGN BY U.S BLASTER - P.O. Box 5376 - Carefree - AZ 85377-USA.
USB 7013 - 7014
Console mixers
MONO INPUT CHANNELS
1. MIC INPUT
The MIC input accepts XLR-type connectors and is designed to use a wide
range of BALANCED or UNBALANCED signals; it has 48V Phantom power
supply and it can connect high capacity microphones.
Pin 1=Ground, Pin 2=signal+, Pin 3=signal-
2. LINE INPUT
Accepts 3-pole 6.3 mm Jack. It uses this high impedance input for sources
other than mics, such as keyboards, drum machines, synths, tape recor-
ders or guitars. The input is BALANCED for professional equipment, but you
can use UNBALANCED sources by wiring up the jacks as shown in the dia-
gram. You should keep cable lengths as short as possible. Unplug anything
in the MIC input if you want to use this socket. Set the input level using the
SENS knob.
3.INSERT
The unbalanced, pre-EQ insert point is a break in the channel-signal path,
allowing limiters, compressors, special EQ or other signal processing units
to be added in the signal path.The insert is a 6.3 mm Jack socket which is
normally bypassed. When a jack is inserted, the signal path is broken, just
before the EQ section. The send may be tapped off as an alternative pre-
fade, pre-EQ direct output if required, using a lead with tip and ring short-
ed together so that the signal path is not interrupted.
4. GAIN
This knob sets how much of the source signal is sent to the rest of the mixer.
Too high, and the signal will distort as it overloads the channel. Too low, and
the level of any background hiss will be more noticeable and you may not
be able to get enough signal level to the output of the mixer. Setting the
knob to the "U" mark gives unity gain for the LINE input. Note that some
sound equipment, particularly the ones for domestic use, operate at a lower
level(-10 dB) than professional equipment and will therefore need a higher
gain setting to give the same output level. See 'Setting UP &
Troubleshooting' to learn how to set SENS correctly.
5. HI
Controls frequencies higher than 12 kHz. Provides ±15dB upgrade or atte-
nuation.
6. FREQ
Control of frequency, can be adjusted from 140 Hz to 3 KHz.
7. MID
Provides ± 15 dB upgrade or attenuation in the mid frequencies.
8. LOW
Controls frequencies below 80 Hz, which features ±15dB of gain adjust-
ment (cut or boost).
©US Blaster Europe BV
Produktspezifikationen
| Marke: | US Blaster |
| Kategorie: | DJ Party Musik |
| Modell: | USB 7014 |
Brauchst du Hilfe?
Wenn Sie Hilfe mit US Blaster USB 7014 benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten
Bedienungsanleitung DJ Party Musik US Blaster
24 August 2024
20 August 2024
18 August 2024
16 August 2024
16 August 2024
16 August 2024
14 August 2024
13 August 2024
12 August 2024
10 August 2024
Bedienungsanleitung DJ Party Musik
- DJ Party Musik Pioneer
- DJ Party Musik Gemini
- DJ Party Musik Skytec
- DJ Party Musik Vonyx
- DJ Party Musik EnVivo
- DJ Party Musik Numark
- DJ Party Musik Hercules
- DJ Party Musik ION
- DJ Party Musik Koden
- DJ Party Musik Native
- DJ Party Musik Serato
- DJ Party Musik Atomix
Neueste Bedienungsanleitung für -Kategorien-
24 September 2024
27 August 2024
25 August 2024
25 August 2024
25 August 2024
25 August 2024
25 August 2024
25 August 2024
25 August 2024
25 August 2024