Unimac ACM-400s Bedienungsanleitung

Unimac Kompressor ACM-400s

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Unimac ACM-400s (17 Seiten) in der Kategorie Kompressor. Dieser Bedienungsanleitung war für 7 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Download PDF
Seite 1/17
User Manual
[Revision 2021 .0 March 3]
READ THIS MANUAL CAREFULLY BEFORE USE FAILURE TO DO SO MAY RESULT IN INJURY, PROPERTY DAMAGE AND MAY –
VOID WARRANTY. • KEEP THIS MANUAL FOR FUTURE REFERENCE. • Products covered by this manual may vary in appearance,
assembly, inclusions, specifications, and packaging.description,
ACM Oil- 400s - Free Air Compressor
E&OE © 2 2023 Unimac
Safety
Safety messages are designed to alert you to possible dangers or hazards that could cause death, injury or
equipment or property damage if not understood or followed. Safety messages have the following symbols:
You WILL be KILLED or
SERIOUSLY INJURED if you do
not follow instructions.
You CAN be KILLED or
SERIOUSLY INJURED if you do
not follow instructions.
You CAN be INJURED if you do
not follow instructions or equipment
damage may occur.
It is vital that you read and understand this
user manual before using the product,
including safety warnings, and any assembly
and operating instructions. Keep the manual
for future reference.
Safety precautions and recommendations
detailed here must be fully understood and
followed to reduce the risk of injury, fire,
explosion, electrical hazard, and/or property
damage.
Safety information presented here is generic
in nature – some advice may not be
applicable to every product. The term
"equipment" refers to the product, be it
electrical mains powered, battery powered or
combustion engine powered.
• - If you are not familiar with the Before Use
safe operation/handling of the equipment or
are in any way unsure of any aspect of
suitability or correct use for your
application, you should complete training
conducted by a person or organization
qualified in safe use and operation of this
equipment, including fuel/electrical handling
and safety.
• Do NOT operate the equipment in
flammable or explosive environments, such
as in the presence of flammable liquids,
gases, or dust. The equipment may create
sparks or heat that may ignite flammable
substances.
• Keep clear of moving parts.
• Equipment may be a potential source of
electric shock or injury if misused.
• Do NOT operate the equipment if it is
damaged, malfunctioning or is in an
excessively worn state.
• Do NOT allow others to use the equipment
unless they have read this manual and are
adequately trained.
• Keep packaging away from children - risk
of suffocation! Operators must use the
equipment correctly. When using the
equipment, consider conditions and pay
due care to persons and property.
General Work Area Safety
• Work areas should be clean and well it.
• Do not operate the equipment if
bystanders, animals etc are within
operating range of the equipment or the
general work area.
• If devices are provided for connecting dust
extraction / collection facilities, ensure
these are connected and used properly.
Dust collection can reduce dust-related
hazards.
General Personal Safety
• Wear appropriate protective equipment
when operating, servicing, or when in the
operating area of the equipment to help
protect from eye and ear injury, poisoning,
burns, cutting and crush injuries. Protective
equipment such as safety goggles,
respirators, non-slip safety footwear, hard
hat, hearing protection etc should be used
for appropriate equipment / conditions.
Other people nearby should also wear
appropriate personal protective equipment.
Do not wear loose clothing or jewellery,
which can be caught in moving parts. Keep
hair and clothing away from the equipment.
• Stay alert and use common sense when
operating the equipment. Do not over-
reach. Always maintain secure footing and
balance.
• Do not use the equipment if tired or under
the influence of drugs, alcohol, or
medication.
• This equipment is not intended for use by
persons with reduced physical, sensory, or
mental capabilities.
General Fuel Safety
• Petrol/fuel/gasoline is extremely flammable
– keep clear of naked flames or other
ignition sources.
• Do not spill fuel. If you spill fuel, wipe it off
the equipment immediately – if fuel gets on
your clothing, change clothing.
• Do NOT smoke near fuel or when
refuelling.
• Always shut off the engine before
refuelling.
• Do NOT refuel a hot engine.
• Open the fuel cap carefully to allow any
pressure build-up in the tank to release
slowly.
• Always refuel in well ventilated areas.
• Always check for fuel leakage. If fuel
leakage is found, do not start, or run the
engine until all leaks are fixed.
General Carbon-Monoxide Safety
• Using a combustion engine indoors CAN
KILL IN MINUTES. Engine exhaust
contains carbon-monoxide – a poison you
cannot smell or see.
• Use combustion engines OUTSIDE only,
and far away from windows, doors, and
vents.
General Equipment Use and Care
• The equipment is designed for domestic
use only.
• Handle the equipment safely and carefully.
• Before use, inspect the equipment for
misalignment or binding of moving parts,
loose components, damage, or any other
condition that may affect its operation. If
damaged, have the equipment repaired by
an authorised service centre or technician
before use.
• Prevent unintentional starting of the
equipment - ensure equipment and power
switches are in the OFF position before
connecting or moving equipment. Do not
carry equipment with hands or fingers
touching any controls. Remove any tools or
other items that are not a part of the
equipment from it before starting or
switching on.
• Do not force the equipment. Use the
correct equipment for your application.
Equipment will perform better and be safer
when used within its design and usage
parameters.
• Use the equipment and accessories etc. in
accordance with these instructions,
considering working conditions and the
work to be performed. Using the equipment
for operations different from those intended
could result in hazardous situations.
• Always keep equipment components
(engines, hoses, handles, controls, frames,
housings, guards etc) and accessories
(cutting tools, nozzles, bits etc) properly
maintained. Keep the equipment clean and,
where applicable, properly lubricated.
• Store the equipment out of reach of
children or untrained persons. To avoid
burns or fire hazards, let the equipment
cool completely before transporting or
storing. Never place or store the equipment
near flammable materials, combustible
gases, or liquids etc.
• The equipment is not weather-proof, and
should not be stored in direct sunlight, at
high ambient temperatures or locations that
are damp or humid.
• Do not clean equipment with solvents,
flammable or harsh abrasives. liquids,
• For specific equipment safety use and care,
see Equipment Safety.
ACM Oil- 400s - Free Air Compressor
E&OE © 3 2023 Unimac
General Electrical Safety
• Inspect electrical equipment, extension
cords, power bars, and electrical fittings for
damage or wear before each use. Repair or
replace damaged equipment immediately.
• Ensure all power sources conform to
equipment voltage requirements and are
disconnected before connecting or
disconnecting equipment.
• When wiring electrically powered
equipment, follow all electrical and safety
codes.
• Wherever possible, use a residual current
device (RCD).
• High voltage / high current power lines may
be present. Use extreme caution to avoid
contact or interference with power lines.
Electrical shock can be fatal.
General Electrical Safety
• Electrically grounded equipment must have
an approved cord and plug and be
connected to a grounded electrical outlet.
• Do NOT bypass the ON/OFF switch and
operate equipment by connecting and
disconnecting the electrical cord.
• Do NOT use equipment that has exposed
wiring, damaged switches, covers or
guards.
• Do NOT use electrical equipment in wet
conditions or in damp locations.
• Do NOT use electrical cords to lift, move or
carry equipment.
• Do NOT coil or knot electrical cords, and
ensure electrical cords are not trip hazards.
General Service Information
• The equipment must be serviced or
repaired at authorised service centres by
qualified personnel only.
• Replacement parts must be original
equipment manufacturer (OEM) to ensure
equipment safety is maintained.
• Do NOT attempt any maintenance or repair
work not described in this manual.
• After use, the equipment and components
may still be hot – allow the equipment to
cool and disconnect spark plugs and/or
electrical power sources and/or batteries
from it before adjusting, changing
accessories, or performing repair or
maintenance.
• Do NOT adjust while the equipment is
running.
• Perform -related service activities in suitable
conditions, such as a workshop.
• Replace worn, damaged or missing
warning/safety labels immediately.
Child Choking Hazard!
• WARNING: CHOKING HAZARD - CHILDREN UNDER 8 YRS. CAN CHOKE OR SUFFOCATE ON SMALL PARTS. ADULT
SUPERVISION REQUIRED.
• Carefully inspect anything a baby or child could gain access to, including this product & packaging.
• Dangers include anything of a size that could become stuck or lodged in a baby or child's airway.
• Dangers include things like raw, hard fruit and vegetable pieces, large pieces of meat, bones or sausage skins, popcorn, nuts,
hard lollies and corn chips, small magnets and batteries, coins, beads, marbles and small uninflated balloons, broken toys and smaller toys,
buttons, keys and coins. But there are also many more.
• Pay particular attention to accessories, nuts, bolts, screws, washers, caps, covers, loose parts, parts that could be removed or break off, pieces
of packaging, staples, tape etc.
• In the case of any doubt, secure the item of concern in an appropriate manner, or completely remove the possibility of access by a baby or child.
General Safety Warnings
• WARNING! READ AND UNDERSTAND ALL INSTRUCTIONS. FAILURE TO FOLLOW ALL INSTRUCTIONS LISTED BELOW, MAY RESULT
IN ELECTRIC SHOCK, FIRE AND/OR SERIOUS PERSONAL INJURY.
• Read all instructions. Know your power tool. Read the operator’s manual carefully. Learn the applications and limitations as well as the specific
potential hazards related to this tool.
Work Area Safety
• Keep work area clean. Cluttered areas and benches invite accidents. Do not leave tools or pieces of wood on the tool while it is in operation.
• Do not use in dangerous environments. Do not use power tools in damp or wet locations or expose to rain. Keep the work area well lit.
• Keep children and visitors away. All visitors should wear safety glasses and be kept a safe distance from work area. Do not let visitors contact
tool or extension cord while operating.
• Never use in an explosive atmosphere. Normal sparking of the motor could ignite fumes.
Electrical Safety
• Guard against electrical shock by preventing body contact with grounded surfaces, e.g., pipes, radiators, ranges, refrigerator enclosures.
• Do not abuse cord. Never carry tool by the cord or yank it to disconnect from receptacle. Keep cord from heat, oil, and sharp edges.
• Should any electrical component of the tool fail to perform properly, shut off the power switch, remove the plug from the power source and
replace before resuming operation.
• Do not expose power tools to rain or wet conditions. Water entering a power tool will increase the risk of electric shock.
Personal Safety
• Stay alert and exercise control. Watch what you are doing and use common sense. Do not operate tool when you are tired. Do not rush.
• Dress properly. Do not wear loose clothing, neckties, or jewellery that can get caught and draw you into moving parts. Rubber gloves and non-
skid footwear are recommended when working outdoors. Also wear protective hair covering to contain long hair.
• Always wear safety glasses with side shields. Everyday eyeglasses have only impact resistant lenses; they are not safety glas ses.
• Protect your lungs. Wear a face or dust mask if the operation is dusty.
• Protect your hearing. Wear hearing protection during extended periods of operation.
• Do not overreach. Always keep proper footing and balance.
• Remove adjusting keys and wrenches. Form habit of checking to see that keys and adjusting wrenches are removed from tool before turning it
on.

Produktspezifikationen

Marke: Unimac
Kategorie: Kompressor
Modell: ACM-400s

Brauchst du Hilfe?

Wenn Sie Hilfe mit Unimac ACM-400s benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten


Bedienungsanleitung Kompressor Unimac

Unimac

Unimac ACM-150s Bedienungsanleitung

2 September 2024
Unimac

Unimac UMC-12P Bedienungsanleitung

5 August 2024
Unimac

Unimac ACM-500s Bedienungsanleitung

4 August 2024
Unimac

Unimac ACM-400s Bedienungsanleitung

4 August 2024
Unimac

Unimac ACM-250s Bedienungsanleitung

4 August 2024
Unimac

Unimac UMC-15P Bedienungsanleitung

3 August 2024
Unimac

Unimac ACM-500 Bedienungsanleitung

26 Juli 2024
Unimac

Unimac AIRPTLUMCA12P Bedienungsanleitung

4 Juli 2024
Unimac

Unimac ACM-200s Bedienungsanleitung

8 Juni 2024
Unimac

Unimac ACM-160s Bedienungsanleitung

8 Juni 2024

Bedienungsanleitung Kompressor

Neueste Bedienungsanleitung für -Kategorien-

MSW

MSW -SPS-24 Bedienungsanleitung

15 Oktober 2024
MSW

MSW -UVRSRI Bedienungsanleitung

15 Oktober 2024
FERM

FERM CRM1027 FCO-1524 Bedienungsanleitung

14 Oktober 2024
FERM

FERM SGM1011 Bedienungsanleitung

9 Oktober 2024
Ozito

Ozito ACP-2115K Bedienungsanleitung

9 Oktober 2024
Sun Joe

Sun Joe 24V-AJC-LTW-RM Bedienungsanleitung

28 September 2024
Auto Joe

Auto Joe 24V-AJC-LTE-RM Bedienungsanleitung

17 September 2024
Draper

Draper 110V 6L Bedienungsanleitung

17 September 2024
Powerplus

Powerplus POWX1731 Bedienungsanleitung

14 September 2024
Güde

Güde 190/08/24 Bedienungsanleitung

14 September 2024