Uniden UPP 136 Bedienungsanleitung


Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Uniden UPP 136 (4 Seiten) in der Kategorie Nicht kategorisiert. Dieser Bedienungsanleitung war für 20 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Seite 1/4
- 1 -
Portable Power Bank &
Jump Start Kit
UPP136
USB Output 2
(Charge mobile devices)
DC Output
(12V/16V/19V devices)
POWER Switch
(ON/OFF)
Power Button
(Flashlight & Power Modes)
DC INPUT
(Charge the UPP136)
Flashlight
LED Display
12V Connector
(Jump start)
USB Output 1
(Charge mobile devices)
• 13600mAh Capacity
• Universal 12V clamps
• Supports Engines
< 5.0L Petrol
< 3.0L Diesel
• USB Port 5V/2.1A Port
• LED Flashlight
• Laptop Connector
• AC/DC Chargers
• Resting Discharge
– 20% Loss/Year
• Carrying Case
FEATURES
WHAT’S INCLUDED
• UPP136 portable power unit
• 8 pcs laptop charging connector with charger leads
• 2–1 USB connector (Micro, Mini)
• Smart Jumper Cable adaptor
• 12-15V DC cigarette lighter adaptor (vehicle adaptor)
• 15V/1.0A AC Adaptor
SLIDE ON THE POWER SWITCH BEFORE YOU DO THE
FOLLOWING:
Charge the unit
- Charge the USB device
- Charge DC12V/16V/19V device
- Use the Flashlight
- Use the Air Pump (Not Included)
USING THE UPP136 POWER BANK
CHARGING THE UNIT
1. Use the 240V AC Adaptor to connect the unit to an AC home outlet
or the cigarette lighter adaptor to connect the unit to the vehicle’s
cigarette lighter socket.
2. Slide ON the POWER switch to monitor charging progress on the
screen. The display shows 100% with when charging is complete.
3. Disconnect the UPP136 from the AC adaptor.
To preserve battery life, fully charge the Power Bank every three
months.
CHECK BATTERY CAPACITY
1. Slide ON the POWER switch.
2. Press POWER button without any devices connected to the char-
ger.
3. The number of bars in the battery icon indicate the power in the
battery.
JUMP START A VEHICLE
1. Slide ON the POWER switch and make sure the Power Bank is
fully charged.
2. Turn off all accessories on the vehicle (radio, air conditioner, etc)
3. Connect the jumper cable’s RED clamp to the POSITIVE post of
the vehicle battery.
4. Connect the jumper cable’s BLACK clamp to the NEGATIVE post
of the vehicle battery.
5. Insert the jumper cable connector into the Power Bank’s 12V
connector (under ap). Be sure the connection is solid.
6. Turn the vehicle ignition key for 3 seconds only. If the vehicle
starts:
• Disconnect the jumper cables from the power pack rst, then
disconnect the clamps from the battery.
• Leave the ignition on for a few minutes, then turn off the
vehicle.
• Start the car.
7. If the car does NOT start on the îš¿rst try, wait for a minute and try
again.
CHARGING A 5V USB DEVICE (TABLET, CELL PHONE, ETC.)
1. Slide ON the POWER switch. Connect 2-1 USB connector to the
UPP136.
2. Connect your device to either the miniUSB or microUSB cable.
3. The UPP136 begins to charge your device.
TURN ON FLASHLIGHT
1. Slide ON the POWER switch. Press and hold POWER button to
turn on the LED ashlight in steady mode.
2. Press POWER button again to cycle through the 4 modes: Steady,
- 2 - - 3 -
Slow Strobe, Fast Strobe, and OFF.
CHARGE DC12V/16V/19V DEVICES
Slide ON the POWER switch. Press POWER button to select the
desired output voltage (DC 12V/16V/19V). Insert a connector cable
(not included) to DC Output 2 to charge the desired device.
MAINTENANCE
Use common sense when caring for your UPP136. Be sure the
connectors and jacks remain clean and free of debris. Unplug the
UPP136 after charging. Slide OFF the POWER switch and store the
UPP136 and its accessories in the carrying case provided.
BATTERY DISPOSAL
The battery is self-contained and not consumer replaceable. The battery
must be disposed properly when it no longer holds a charge. Proper
charging practices will increase the life of the unit.
TROUBLESHOOTING
IF... TRY THIS...
My items are not recharging/
inating.
• Recharge the UPP136.
• Verify that your items are connected cor-
rectly.
I haven’t used my UPP136
in a while, and now the unit
is completely drained.
You may have accidentally put it away with it
powered on. Recharge it.
USING THE AIR PUMP (OPTIONAL ACCESSORY)
The air pump accessory comes equipped to pump air into car tires.
Do not use the air pump longer than 15 minutes at a time. Let it
cool down after 5 minutes of continuous use.
1. Connect the appropriate air needle adaptor to the air pump, if
needed.
2. Connect the air hose to the item to inate.
3. Connect the air pump’s power plug to the Power Bank’s 12V Con-
nector (under ap).
4. Press the green power button on the air pump. Monitor the gauge
to be sure not to overinate your item. Stop inating your item oc-
casionally to check the air pressure.
5. Press the green power button again when the item is inated to
turn off the air pump.
SPECIFICATIONS
Power Bank
Operating Temperature – 20 ~ + 60 C° °
Start Current 250A
Peak Current 500A
Capacity 13600mAh/50.32WH
Cycle life 1,000 times
Charge mode DC 15V 1A
USB output 5V 2A
DC Output 12V
- 4 - - 5 -
Air Pump ( Optional Accessory)
Power Input 12V DC
Maximum Pressure 80 PSI
Maximum Current 4A
Unloaded Current <2.5A
Inating Speed Less than 10 minutes to inate tire from 0 to 30
PSI based on tire size 195/55R15.
Working Temperature –10 ~ +60 C° °
Dimensions 10.8 X 9.5 X 4.7 cm


Produktspezifikationen

Marke: Uniden
Kategorie: Nicht kategorisiert
Modell: UPP 136

Brauchst du Hilfe?

Wenn Sie Hilfe mit Uniden UPP 136 benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten




Bedienungsanleitung Nicht kategorisiert Uniden

Bedienungsanleitung Nicht kategorisiert

Neueste Bedienungsanleitung für -Kategorien-