Uniden ADV05-3 Bedienungsanleitung

Uniden Radio ADV05-3

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Uniden ADV05-3 (1 Seiten) in der Kategorie Radio. Dieser Bedienungsanleitung war für 13 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Download PDF

Seite 1/1

15141312

111098

7654

321

UNIDEN AUSTRALIA PTY LTD

Phone: 1300 366 895

Email: custservice@uniden.com.au

Procedure for obtaining warranty service: Depending on the country in

which the Product was first purchased, if you believe that your Product does

not conform with this warranty, you should deliver the Product, together with

satisfactory evidence of your original purchase (such as a legible copy of

the sales docket) to Uniden at the address shown below. You should contact

Uniden regarding any compensation that may be payable for your expenses

incurred in making a warranty claim. Prior to delivery, we recommend that you

make a backup copy of any phone numbers, images or other data stored on

your Product, in case it is lost or damaged during warranty service.

Our goods come with guarantees that cannot be excluded under the Australian

Consumer Law. You are entitled to a replacement or refund for a major failure

and for compensation for any other reasonably foreseeable loss or damage.

You are also entitled to have the goods repaired or replaced if the goods fail to

be of acceptable quality and the failure does not amount to a major failure.

This warranty is in addition to and sits alongside your rights under either the

COMPETITION AND CONSUMER ACT 2010 (Australia) or the CONSUMER

GUARANTEES ACT (New Zealand) as the case may be, none of which can be

excluded.

Statement of Remedy: If the Product is found not to conform to this warranty

as stated above, the Warrantor, at its discretion, will either repair the defect or

replace the Product without any charge for parts or service. This warranty does

not include any reimbursement or payment of any consequential damages

claimed to arise from a Products failure to comply with the warranty.

IMPORTANT: Satisfactory evidence of the original purchase is required

for warranty service

Please refer to our Uniden website for any details or warranty durations offered in

addition to those contained below.

Warrantor: The warrantor is Uniden Australia Pty LimitedABN 58 001 865 498

(Uniden) .

Terms of Warranty: Uniden Aust warrants to the original retail purchaser only

that the ADV05 Series (the Product), will be free from defects in materials and

craftsmanship for the duration of the warranty period, subject to the limitations and

exclusions set out below.

Warranty period: This warranty to the original retail purchaser is only valid in the

original country of purchase for a Product first purchased either in Australia or New

Zealand and will expire one (1) year from the date of the original retail sale.

If a warranty claim is made, this warranty will not apply if the Product is found by

Uniden to be:

(A) Damaged or not maintained in a reasonable manner or as recommended

in the relevant Uniden Owners Manual;

(B) Modified, altered or used as part of any conversion kits, subassemblies or

any configurations not sold by Uniden;

Owners Manual

(D) Repaired by someone other than an authorized Uniden Repair Agent in

relation to a defect or malfunction covered by this warranty; or

(E) Used in conjunction with any equipment, parts or a system not

manufactured by Uniden.

Parts Covered: This warranty covers the Product and included accessories.

User-generated Data: This warranty does not cover any claimed loss of or

damage to user-generated data (including but without limitation phone numbers,

addresses and images) that may be stored on your Product.

UNIDEN ADV05 Series UHF CB Transceiver

WARRANTY

CTCSS Codes 01 - 38

Code

Frequency

(Hz)

Code

Frequency

(Hz)

Code

Frequency

(Hz)

Code

Frequency

(Hz)

1 67

71.9

74.4

79.7

82.5

85.4

88.5

91.5

94.8

97.4

100

103.5

107.2

110.9

114.8

118.8

123

127.3

131.8

136.5

141.3

146.2

151.4

156.7

162.2

167.9

173.8

179.9

186.2

192.8

203.5

210.7

218.1

225.7

233.6

241.8

250.3

28 38

10 20 30

WATER WARNING

Uniden does not represent this product to be waterproof.

Do not expose this product to Rain or Moisture.

User License Information

NOTE

USER LICENSE INFORMATION

The citizen band radio service is licenced in Australia by ACMA

Radio-communications (Citizen Band Radio Stations) Class

Licence and in New Zealand by MBIE General User Licence

for Citizen Band Radio and operation is subject to conditions

contained in those licenses.

NOTE

Always listen on a channel (or observe the receive signal level

meter) to ensure it is not already being used before transmitting.

Channels 5 and 35 are used for emergency channels.

CTCSS will not operate on these channels.

Please follow these guidelines for channel use in Australia:

 Channels 05 and 35 are Emergency Channels.

 Channel 11 is a Calling Channel.

 Channels 22 and 23 are for telemetry and telecommand

applications, channels 61, 62 and 63 are for future use and TX is

inhibited on these channels.

General communication is accepted on all other channels

with these guidelines:

 Channel 40 - road channel (Australia).

 Channels 01-08 (and 31-38), and Channels 41-48

(and 71-78) are repeater channels.

NOTE

Important information - 80 Channel UHF-CB channel expansion

To provide all users additional channel capacity within the UHF-CB

Band. The ACMA will change the majority of the current wideband 40

channel use to narrowband channel use. This allows for additional

channels to be added, up to 80 Channels.

This simply means that the new narrowband radio you have purchased

will have more channels than older radios. Please refer to the guidelines

above and the channel chart for further channel information.

A list of currently authorised channels can also be obtained from the

ACMA website in Australia and the MBIE website in New Zealand.

Interference / Poor Audio

When a new narrowband radio receives a signal from an older

wideband radio the speech may sound loud.

Narrowband radios operating on CH41 - CH80 may encounter

interference from a nearby wideband radios transmitting on high

power on an adjacent channel (frequency).

When an older wideband radio receives a signal from a new

narrowband radio the speech may sound quiet - the wideband radio

user simply adjusts their radio volume for best performance.

The above situations are not a fault of the radio but a symptom of mixed

wideband and narrowband radios in current use. It is expected that as

older wideband radios are phased out this issue will be eliminated.

UHF CHANNELS & FREQUENCIES

Key Lock ON/OFF

1. To lock the key pad:

Press and hold until the key lock indicator appears.

2. To unlock the key pad:

Press and hold until the key lock indicator disppears.

Key Beep ON/OFF

Press and hold the button while turning the radio ON to DOWN

switch the key beep tone ON or OFF.

Roger Beep ON/OFF

Roger Beep is a unique tone added to end a transmission.

Press and hold the button while turning the radio ON to turn UP

Roger Beep ON or OFF.

1. Press MENU six times. r P setting flashes.

2. Press or to change the change the setting ON or OFF.UP DOWN

3. Press to save.PTT

Eg. CH01 is being used in your area for repeater use.

Operation With the Aid of a Repeater

NOTE: You can only activate Duplex on Channels 01-08 and

41-48. When Duplex is ON for a repeater channel, the display

shows r1-r8 for Channels 01-08 and n1-n8 for Channels 41-48.

To Operate in Duplex Mode (Repeater Mode)

The Duplex function enables you to access local repeater

stations. UHF CB Repeaters are used to retransmit or relay your

signal. Repeaters will extend the range of your radio and

overcome the shielding effect caused by solid obstructions.

Dual (Channel) Watch

You can monitor a second channel along with the current

channel with this setting.

1. Press five times. CH appears on the display. MENU

The second channel to monitor will flash. (OF, 01 - 80)

If the setting is OF, then Dual Watch is disabled.

2. Press or to set the 2nd channel to monitor.UP DOWN

3. Press to save the setting and dual watch will be enabled. PTT

The second channel will be monitored intermittently.

3 = High Sensitivity (for noisy areas)

2 = Medium Sensitivity

1 = Low Sensitivity (for quieter areas)

Voice Operated Transmission (VOX)

Transmission is initiated by speaking into the microphone of the

radio instead of pushing the PTT button.

Press to turn VOX On or Off. appears on the display.VOX VOX

The VOX sensitivity level can be changed in the Menu.

1. Press four times. icon will display.MENU VOX

The current setting (1-3) will flash.

2. Press and button to select the sensitivity level.UP DOWN

3. Press to set the new setting.PTT

Setting and Transmitting Call Tones

Your radio can transmit different call tones (wake-up tone) to

other radios in your group so you can alert them that you want to

talk. To set a call tone:

1. Press the three times. CA appears on the display. MENU

The current call tone setting flashes.

2. Press or to change and hear the next call tone.UP DOWN

There are 5 call tones to choose from (1-5)

Set the call tone to 0 to disable the call tone feature.NOTE:

3. Press to set the new call tone. PTT

Press to transmit the call tone.CALL

NOTE: Current regulations require calling tones to be restricted

to one transmission per minute. If a second transmission is

attempted within one minute then an error tone will sound.

Scan Advance

If the radio stops scanning on a channel you do not want to listen

to, briefly press and release or to temporarily remove UP DOWN

that channel from scan and resume scanning. Removed chanels

are restored when the radio is powered off then on again.

Scanning Channels

Use scanning to monitor channels for transmissions or to find

someone in your group who has accidentally changed channels.

To start scanning:

1. Press and release . The indicator displays. SCAN SCAN

2. Press and release again to disable scanning. SCAN

The indicator disappears. SCAN

When the radio detects channel activity, it stops scanning and

you can hear the transmission. To respond to the transmission,

press within 5 seconds,the channel will be confirmed.PTT

CTCSS and DCS Codes - Silent PIN

When you dont want to hear chatter from other users on a

channel, who are not part of your group, you can set a

Silent PIN (CTCSS or DCS code). The silent pin works to keep

your radio silent, unless someone is transmitting using the same

silent pin - so only share your pin setting with those in your

group. The ADV05 has 104 pins (codes) available (01~104).

The radios in your group must be set to the same Silent PIN

(CTCSS or DCS code). When communicating with other ADV

series radios you just select the same pin code. You can set a

different pin code for each channel using this procedure.

1. Set a desired channel to use a Silent PIN on.

2. Press two times. The PIN (code) number flashes.MENU

3. Press or to select a setting;UP DOWN

- PIN 00 Setting is disabled (Off)

- PINs 01~38 (CTCSS codes 01~38)

- PINs 39~104 (DCS codes 39~104).

Ex. 1 shows Silent PIN 38

(CTCSS code #38)

Ex. 2 shows Silent PIN 104

(DCS code #104)

4. Press to save the code setting.PTT

NOTE: Set to 00 to disable the feature for the current channel.

If you are communicating with non ADV series radios then let

them know the code type (CTCSS or DCS) and number your are

using.

Push to Talk Timeout Timer

To prevent accidental transmissions and save battery life, the

radio emits a continuous warning tone and stops transmitting if

you press for 60 continuous seconds.PTT

Checking the Channel Before Transmitting

For uninterrupted communication, do not talk on a channel if

someone else is currently talking on it. Indicates a signal is

being received.

If a Silent PIN (CTCSS code) is enabled, check for activity on a

channel before you talk, press and hold . If you hear static, MON

the channel is clear to use.

NOTE

For maximum range and extended the life of the

batteries, with your avoid touching the antenna

hand when transmitting.

Talking and Listening

To communicate, all radios in your group must be set to the

same Channel (and the same Silent PIN code if it is set).

To talk, press and hold . Indicates transmission. PTT

The transmit power is 0.5 Watt.

Hold the radio 5 to 7 cm away from your mouth when speaking.

When you are finished speaking, release to listen.PTT

Automatic SQUELCH

The ADV05 is equipped with an automatic squelch, which mutes

the speaker audio unless a strong enough signal is present. As

this is automatic, there is no user input required to adjust it.

LED Flashlight (LAMP)

To use the built-in LED flashlight;

1. Press to turn the LED flashlight On or Off.LAMP

The lamp function will work when radio power is Off.NOTE:

Setting a Channel

The ADV05 uses the UHF-CB channels (CH01-CH80). See UHF

CHANNELS & FREQUENCIES, page 12 for channel usage.

1. Press one time. The current channel flashes.MENU

2. Press or button to select a desired channel.UP DOWN

3. Press to confirm and save the channel setting.PTT

One CHANNEL setting

Two Silent PIN (CTCSS Code) setting

Three Call Tone setting

Four VOX setting

Five Dual Watch (2nd Channel) setting

Six Duplex Mode (Repeater) setting

Open the MENU - Press MENU

Step through MENU - Press againMENU

Exit the MENU - Press PTT

MENU List

Ex. lowest volume Ex. highest volume

Setting the Volume

Press the button to increase the speaker volume.UP

Press the button to decrease the speaker volume.DOWN

The speaker volume setting is indicated by L.

The volume level range is from

0 (mute) to 7 (maximum).

When volume level is 0,

the mute icon displays.

Turning Your Radio On and Off

Press and hold to turn the radio On or Off.

When turning on, the radio chirps

and the display briefly shows all the

display icons before showing the

current standby mode of your radio.

OPERATION

Back Light

The ADV05 has an automatic display back light which remains

on for 5 seconds after a key press (all keys except key).PTT

The back light will work even if the keypad is locked but will not

work during low battery alert mode.

Power Save

Your ADV05 Series has a unique circuit designed to dramatically

extend the life of the batteries. If there is no transmission nor an

incoming call within 5 seconds, your Radio switches to the

Power Save mode. The Radio is still able to receive transmis-

sions in this mode.

Low Battery Alert

If the battery level becomes low, the unit will go into a Battery

Low Mode. The Transmit Mode is disabled. Replace Alkaline

batteries immediately, or recharge NiMH rechargeable batteries

immediately to continue using the radio.

NOTE

Do not charge alkaline or non rechargeable batteries.

Plug the Micro-USB end of the USB charge cable into the radios

Micro-USB charge port, and the USB end to a standard USB

charge port, or USB port of an AC adaptor (not included). Plug the

AC adaptor into the wall outlet.

 Before operating the radio, charge the rechargeable batteries

for 16 hours without interruption.

 Do not transmit when the radio is charging.

The changing battery icon on the display indicates the battery is

charging.

Charging Rechargeable Batteries

3. Replace the battery cover and press down to secure.

Installing the three AAA alkaline

or NiMH batteries.

Belt Clip

To attach:

Slide the belt clip down into the catch until it snaps into place.

To remove:

Pinch and hold belt clip latch and slide the belt clip up.

Battery bars indicate the battery level . When the battery

meter shows 1 bar, the device goes into low battery mode and

indicates low battery in the form of an alert tone.

NOTE

- Charge only at room temperatures.

- Only charge NiMH rechargeable batteries.

- Do not mix and use old/new/alkaline/NiMH batteries.

- Remove the batteries from the radio for storage.

- Batteries may corrode over time and cause

permanent damage to your devices.

- Charge rechargeable NiMH batteries once every

3 months when not in use.

Radio Battery Meter

2. Install 3 AAA Alkaline batteries or 3 AAA NiMH rechargeable

batteries as shown on the inside of the battery compartment.

Push

Slide to open

battery door

1. With the back of the radio facing you, push and slide down the

battery cover to remove.

Your radio requires 3 AAA Alkaline batteries or 3 AAA NiMH

Rechargeable batteries (not supplied).

Installing Batteries

GETTING STARTED

VOX is on

Scan is on

Battery Level

Transmit / Receive

Key Lock is on

Dual Channel is on

Volume Mute

Silent PIN

(CTCSS Code)

for current Channel

Channel Number

* Requires 3 AAA rechargeable batteries to use this feature.

NiMH rechargeable batteries are recommended.

Antenna

Push To Talk

(PTT)

Speaker

Microphone

Display

Lanyard hole

LED Flashlight

Scan / VOX On/Off

Menu / Power On/Off

Call Tone /

Monitor On/Off

Micro-USB

Charging Jack

Flashlight

/ Key Lock

Display Icons: See page 2

Included in your Package

 ADV05 Series Radio*

 Belt Clip*

 Micro-USB charge cable*

 Operating Guide (one only)

* Per radio

CONTROLS & INDICATORS

For more exciting new products please visit our website:

Australia: www.uniden.com.au

ADV05 Series

UHF CB Transceiver

Produktspezifikationen

Marke:	Uniden
Kategorie:	Radio
Modell:	ADV05-3

Brauchst du Hilfe?

Wenn Sie Hilfe mit Uniden ADV05-3 benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten

Ihren Namen*

Deine E-Mail*

Schreiben Sie hier Ihre Frage

Bedienungsanleitung Radio Uniden

Uniden UH45CP Bedienungsanleitung

12 Oktober 2024

Uniden UH8050S Bedienungsanleitung

8 Oktober 2024

Uniden UH090 Bedienungsanleitung

24 September 2024

Uniden ADV05-3 Bedienungsanleitung

20 September 2024

Uniden UH044DP Bedienungsanleitung

19 September 2024

Uniden UH45 Bedienungsanleitung

19 September 2024

Uniden UH012 Bedienungsanleitung

18 September 2024

Uniden EZI30XLT Bedienungsanleitung

5 September 2024

Uniden GMR3799-2CKHS Bedienungsanleitung

1 September 2024

Uniden Bearcat 880 Bedienungsanleitung

28 August 2024

Bedienungsanleitung Radio

Neueste Bedienungsanleitung für -Kategorien-

Ruarkaudio Rseven Bedienungsanleitung

16 Oktober 2024

Ruarkaudio MR1 Bedienungsanleitung

16 Oktober 2024

Denver TWE-55B Bedienungsanleitung

15 Oktober 2024

AudioSonic CL-1486 Bedienungsanleitung

14 Oktober 2024

Sangean DPR-39 Bedienungsanleitung

14 Oktober 2024

Sangean RCR-9 Bedienungsanleitung

14 Oktober 2024

PerfectPro Dabbox Bedienungsanleitung

13 Oktober 2024

Sencor SIR 5000WDB Bedienungsanleitung

11 Oktober 2024

AEG KRC 4350 BT Bedienungsanleitung

10 Oktober 2024

Zebra Talkabout MD200TPR Bedienungsanleitung

8 Oktober 2024