Tycon Systems RemotePro Bedienungsanleitung

Tycon Systems Solaranlage RemotePro

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Tycon Systems RemotePro (12 Seiten) in der Kategorie Solaranlage. Dieser Bedienungsanleitung war für 46 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Download PDF

Seite 1/12

RPST

RemotePro®

Remote Power System

▫ Wireless Base Stations

and Client Devices

▫ Surveillance Cameras

▫ Remote Sensors

▫ Remote Lighting

▫ Off Grid Electronics

Congratulations! on your purchase of the RemotePro off grid ™ -

remote power system. Please take a moment to review this Qwik

Install Guide before assembly or battery installation.

DANGER! Avoid Powerlines!

You Can Be Killed!

When following the instructions in this guide take extreme care

to avoid contact with overhead power lines, lights and power circuits.

Contact with power lines, lights or power circuits may be fatal. We rec-

ommend to install no closer than 20 feet to any power lines.

Safety: For your own protection, follow these safety rules.

▫ Perform as many functions as possible on the ground

▫ Do not attempt to install on a rainy, windy or snowy day or if

there is ice or snow accumulation at the install site or if the

site is wet.

▫ Make sure there are no people, pets, etc. below when you are

working on a roof or ladder.

Recommended Tools: Phillips Screwdriver, 13mm and 10mm

Wrench, nut driver, Flat Blade Screwdriver5/16”

Please help preserve the environment and return

used batteries to an authorized depot

Qwik Install

STEP 1: Add Grounding Wire Between Door and Enclosure: Remove

plastic covers on copper studs on

inside of door and inside of enclo-

sure. Add jumper wire between 2

copper studs and use copper wash-

ers and nuts to secure.

STEP 2: Remove the bottom cover

and replace it with the PowerVent™

included with the package. Add wire

feedthrus and any necessary con-

nectors into the bottom PowerVent™

plate.

STEP 3: Install hole plug in drain

hole in bottom right corner of the en-

closure.

STEP 4: Mount the DIN rail to the

door using screws provided. Mount

any extra equipment to the orange

backplate and secure the backplate in

the enclosure. Note: The DIN rail can

also be mounted to the orange back-

plate or sides of enclosure if desired.

STEP 5: If pole mounting the enclo-

sure, assemble the pole mount kit to

the back of the enclosure and mount

the enclosure to a pole using the 6 hose clamps provided. The enclo-

sure can also be wall mounted using the 4 holes in the back of the en-

closure.

STEP 6: Insert the battery

platform in the bottom of the

enclosure. The battery plat-

form has cutouts so wires

can be routed under the bat-

tery as needed.

STEP 7: Attach the green DIN Rail adapters to the charge controller

using the screws provided. Clip the control-

ler to the DIN rail. For the NOTE: TP- -SC24

20 charge controller with LCD display, the

green clip attaches using 1 screw only.

STEP 8: Assemble the solar panel mount

and set the correct tilt angle based on your

Latitude. There is a useful tool to calculate

optimum angle at http://tyconsystems.com If

you will be using a fixed angle all year we

recommend using the optimum angle for

winter sun. You can also calculate winter tilt

using: Your_Latitude*0.9+30. Mount the so-

lar panel mount to the pole using hose clamps provided. Be sure to

mount high enough so the door of the enclosure clears the solar panel

mount when opened. You can also mount the panel to a wall using lag

bolts.

NOTE: If the Solar Controller is model you must wire TP-SCPOE xx 12

batteries and solar for 12V configuration. If Solar controller is model TP

- -SCPOE 24xx you must wire solar panels

and batteries for 24V configuration. Basically

Batteries / Solar / Controller must be same

voltage. The controller is auto TP- -SC24 20

ranging and will detect 12V or 24V.

STEP 9: Attach the solar panel to the solar

panel mount so that the wire junction box is

towards the top or side.

If the solar panel is already connectorized,

connect the solar panel MC 4 connectors to -

the included solar cable.

If the solar panel is not connectorized, re-

move the cover from the solar panel junction box by unscrewing or re-

leasing the 6 snaps. Connect the included octopus cable wires to the +

and - screws inside the junction box. Replace the cover making sure it

is fully snapped.

NOTE: When wiring 2 panels in a 24V configuration you will have two

unused wires on the octopus cable assembly. Wrap the ends with elec-

trical tape to avoid any shorting of the panels. Mount so octopus cable

is under the solar panel to protect it from direct weather.

Produktspezifikationen

Marke:	Tycon Systems
Kategorie:	Solaranlage
Modell:	RemotePro
Gewicht:	62000 g
Produktfarbe:	Schwarz
Akku-/Batterietechnologie:	Plombierte Bleisäure (VRLA)
Akku-/Batteriespannung:	24 V
Akkus/Batterien enthalten:	Ja
Bemessungsleistung:	320 W
Maximale Ausgangsspannung:	24 V