Tristar BD-4610 Bedienungsanleitung

Tristar Blutdruckmessgerät BD-4610

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Tristar BD-4610 (5 Seiten) in der Kategorie Blutdruckmessgerät. Dieser Bedienungsanleitung war für 3 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Download PDF
Seite 1/5
BD-4610
EN | Instruction manual
PT | Manual de utilizador
B
D
PARTS DESCRIPTION / DESCRIÇÃO DOS COMPONENTES
DISPLAY
1
2
1
2
7
3
3
4
5
8
9
6
4
WWW.TRISTAR.EU
Tristar Europe B.V. | Jules Verneweg 87
5015 BH Tilburg | The Netherlands
ENInstruction manual
SAFETY
MEDICAL DISCLAIMER: This device and manual are not meant
to be a substitute for advice provided by doctors or other
medical professionals.
Contact your physician for interpretation of measurements, or if
you have or suspect you have a medical issue.
• By ignoring the safety instructions the
manufacturer can not be hold
responsible for the damage.
• Not for use by children, pregnant women,
or pre-eclamptic patients.
• Prolonged over-inflation of the monitor
will result in harmful injury to the patient.
• Do not use this device over a wound, as
this can cause further injury.
• Too frequent measurements can cause
injury due to blood flow interference.
• Do not attempt to modify this device in
any way.
• Never move the appliance by pulling the
cord and make sure the cord can not
become entangled.
• The appliance must be placed on a
stable, level surface.
• This product is for household use only. It
is not intended as a substitute for
consultation with your doctor.
• For users diagnosed with common
arrhythmia (atrial or ventricular
premature beats or atrial fibrillation),
diabetes, poor circulation of blood,
kidney problems, or for users suffered
from stroke, or for unconscious users,
the device might not be suitable for use.
Consult your doctor in case of any doubt.
• The unit should not be operated by
children to avoid hazardous situations.
• The unit contains high-precision
assemblies. Therefore, avoid extreme
temperatures, humidity and direct
sunlight. Avoid dropping or strongly
shocking the main unit, and protect it
from dust.
• Leaking batteries can damage the unit.
Remove the batteries when the unit is
not used for a long time.
• If the unit is stored in a cold place, allow
it to acclimatize at room temperature
before use.
• To avoid inaccurate results caused by
electromagnetic interference between
electrical and electronic equipment’s, do
not use the device near a cell phone or
microwave oven.
• To protect yourself against an electric
shock, do not immerse the cord, plug or
appliance in the water or any other liquid.
• This appliance shall not be used by
children. This appliance can be used by
persons with reduced physical, sensory
or mental capabilities or lack of
experience and knowledge if they have
been given supervision or instruction
concerning use of the appliance in a safe
way and understand the hazards
involved. Children shall not play with the
appliance. Keep the appliance and its
cord out of reach of children. Cleaning
and user maintenance shall not be made
by children.
SAFETY BATTERIES
• Do not expose the battery to high
temperatures or direct sunlight. Never
throw batteries into the fire. There is a
danger of explosion!
• Keep batteries away from children.
Batteries are not a toy!
• Do not open the batteries by force.
• Avoid contact with metallic objects.
(Rings, nails, screws et cetera) there is a
danger of short-circuiting!
• As a result of a short-circuit batteries
may heat up consider-ably or even catch
fire. this may result in burns.
• For your safety the battery poles should
be covered with adhesive strips during
transport.
• Do not touch a ruptured and/or leaking
battery. If the liquid from the battery gets
into your eyes, rinse your eyes as soon
as possible with clean water, without
rubbing your eyes. Immediately go to the
hospital. If it is not treated properly, it can
cause eye problems.
BLOOD PRESSURE
What is blood pressure?
Blood pressure is the pressure exerted on the artery tube while
blood flows through the arteries. The pressure measured when
the heart contracts and sends blood out of the heart is systolic
(highest). The pressure measured when the heart dilates with
blood flowing back into the heart is called diastolic (lowest)
blood pressure.
Why measure your blood pressure?
Among the various health problems afflicting modern people,
problems associated with high blood pressure are by far the
most common. High blood pressure's dangerously strong
correlation with cardiovascular diseases and high morbidity has
made measuring blood pressures a necessity of identifying
those at risk.
Blood pressure standard.
The World Health Organization (WHO) and National High Blood
Pressure Education Program has developed a Blood pressure
standard, according to which areas of low and high-risk blood
pressure are identified. This standard however, is a general
guideline as individual's blood pressure varies among different
people and different groups...etc.
It is important that you consult your physician regularly. Your
physician will tell you your normal blood pressure range as well
as the point at which you will be considered at risk.
Blood pressure fluctuation
Blood pressure fluctuates all the time!
You should not be worried if you encountered two or three
measurements at high levels.
Blood pressure changes over the month and even throughout
the day depending on circumstances (state of mind,
temperature, ...)
Blood pressure measurements determined with this device are
equivalent to those obtained by a trained observer using the
cuff/ stethoscope auscultatory method, within the limits
prescribed by European Society of Hypertension International
Protocol revision 2010 for the validation of blood pressure
measuring devices in adults.
An irregular heartbeat (IHB) rhythm is defined as a rhythm that
is more than 25% slower or 25% faster from the average rhythm
detected while the device is measuring the systolic blood
pressure and the diastolic blood pressure. When the device
detects an irregular rhythm two or more times during the
measurement, the Irregular Heartbeat Symbol will be displayed
with the measurement values.
PARTS DESCRIPTION
1. Display
2. Start/stop button
3. Memory button
4. Wrist cuff
Display
1. Systolic pressure
2. Diastolic pressure
3. Pulse rate
4. Memory
5. Low battery
6. Pulse detected
7. IHB
8. Date/time
9. User number
BEFORE THE FIRST USE
• Take the appliance andaccessoriesoutthebox.Removethe
stickers,protective foilorplasticfrom thedevice.
Battery Installation:
1. Pull down on the battery cover, located on left side of this
device.
2. Insert two AAA alkaline batteries according to the + and –
markings.
3. Snap the battery cover on, ensuring it clicks into place.
Make sure that the battery cover is securely in position.
4. NOTE: When the low battery symbol appears on screen,
turn off the device and follow the instructions above to
replace batteries.
Setting user, year, date and time:
1. If device is already on immediately after battery installation,
toggle between User 1 and User 2 by pressing "start/stop"
button. If device is turned off, press and hold "mem" button
for 2 seconds, then toggle between user 1 and user 2 by
pressing "start/stop" button. To select user, press "mem" to
confirm and then flashing year digits occur.
2. Press “start/stop” to increase one year or press and hold
“start/stop” to increase several. Press “mem” to confirm and
then flashing month digits occur.
3. Press “start/stop” to increase one month or press and hold
“start/stop” to increase several. Press “mem” to confirm and
then flashing day digits occur.
4. Press “start/stop” to increase one day or press and hold
“start/stop” to increase several. Press “mem” to confirm and
then flashing hour digits occur.
5. Press “start/stop” to increase one hour or press and hold
“start/stop” to increase several. Press “mem” to confirm and
then flashing minute digits occur.
6. Press “start/stop” to increase one minute or press and hold
“start/stop” to increase several. Press “mem” to confirm and
then the device turns off.
USE
Before Taking a Measurement
• For most accurate results, measurements should be taken in
the same circumstances and at the same time every day.
• This device can be applied to either wrist, but preferably the
left. Use the same wrist for each measurement.
• Any blood pressure recording can be affected by the position
and physiological condition of the subject, as well as other
factors such as background noise, stress, talking and body
movement etc.
• Avoid taking measurements while under stress.
• Do not eat, drink alcohol, smoke, exercise, or bathe 30
minutes before using this device, as these activities may
change blood pressure.
• For an accurate indication of true blood pressure, take and
record several measurements over a period of time.
• If consecutive measurements are desired, allow two minutes
between uses to allow blood to flow through the arm normally.
• This device is used to monitor blood pressure. However, it
cannot treat or prevent high blood pressure. If you suffer from
high blood pressure, consult your doctor. Self-diagnosis and
treatment using readings may be dangerous. Follow the
instructions of your physician or licensed healthcare provider.
Measurement
• This device should be used on bare skin. Remove
wristwatches or other jewelry. If necessary, loosely roll up your
sleeve to expose wrist.
• With screen aligned to the midline of your palm and facing
towards you, wrap the cuff around your wrist. Secure this
device cuff firmly by attaching hook-and-loop fastener.
• Comfortably seated, legs uncrossed, feet flat on the floor, back
and arm supported, keep the device at the same level as your
heart, relax as much as possible and do not talk during the
measurement.
• While sitting upright in a chair with your feet flat on the floor,
press “start/stop". Symbols on screen will flash and cuff will
begin to inflate. Do not move, activate arm muscles, or talk
during measurement.
• Measurement can be stopped at any time by pressing “start/
stop".
• When this device senses a pulse, a heart symbol will flash on
screen.
• When measurement is complete, the cuff deflates
automatically and your systolic, diastolic, and pulse rate will
display on screen.
• The screen will change color to indicate the reading. A green
screen indicates normal blood pressure, a yellow screen
indicates a risk of developing high blood pressure and red
indicates high blood pressure. Measurements are
automatically stored in the memory.
• Turn off this device by pressing “start/stop", remove from your
wrist by detaching hook-and-loop fasteners. If this device is
accidentally left on, it will turn itself off after two minutes.
NOTE: This device will remain set on the same user after you
turn it off. To change to the other user, turn this device off then
press and hold “MEM” to access settings. Either the User 1 or
User 2 icon will appear. Press “START/STOP” to switch to the
other user. Press “MEM” six times until the screen turns off.
When you press “START/STOP” again, this device will start as
the other user.
Using Memory-Recall
This device will store up to 90 measurements each for two
users. When more than 90 measurements are taken, the oldest
measurement will be replaced.
• To access memory-recall, press and release “mem” while the
device is off.
• First, it will display the average of your three most recent
measurements, indicated on screen as M (measurement
average).
• Press “mem” again to see the most recent measurement.
Press “mem” repeatedly to scroll towards the oldest
measurement. On screen, M1 indicates the most recent
measurement, with higher M numbers indicating older
measurements.
If you desire to delete all stored measurements of the current
user, press and hold “mem” until “CL” is displayed. Press “start/
stop” to confirm clearing the memory. Press and release “mem”
again and a blank entry should appear on screen. Press “start/
stop” to exit.
TROUBLESHOOTING
Trouble Possible reasons Solution
Err Error during
inflation.
Adjust cuff, ensuring
it is wrapped
properly, and repeat
measurement. Do
not move or talk
during
measurement.
Ensure wrist is level
with heart.
Lo Low battery. Replace batteries
following
instructions in the
Battery installation
section.
No Power Low batteries or
incorrect battery
placement.
Ensure batteries
were installed
according to the +
and - shown on this
device. If they were,
batteries need
replacement.
Measurement Too
High / Too Low
Possible incorrect
use of this device.
Adjust cuff, ensuring
it is wrapped
properly, and repeat
measurement.
CLEANING AND MAINTENANCE
• For regular maintenance, this device only needs to be wiped
gently with a soft, dry cloth. Never immerse this device or any
components in water.
• Do not carry out repairs of any kind yourself. If a defect
occurs, please contact your local authorized distributor. Use
only authorized parts and accessories.
CALIBRATION AND SERVICE
The accuracy of this blood pressure monitor has been carefully
tested and is designed for a long service life. It is generally
recommended to have this device inspected and calibrated
every two years to ensure correct functioning and accuracy.
Please consult you authorized distributor.
EMC DECLARATION
Guidance and Manufacturer’s Declaration - Electromagnetic
Immunity, this device is intended for use in the electromagnetic
environment specified below. The customer or the user of this
device should ensure that it is used in such an environment.
Immunity Test Complianc
eElectromagnetic Environment -
Guidance
RF emissions
CISPR 11 Group 1 This device uses RF energy only
for its internal function.
Therefore, its RF emissions are
very low and are not likely to
cause any interference in nearby
electronic equipment.
RF emissions
CISPR 11 Class B This device is suitable for use in
all establishments other than
domestic and those directly
connected to the public low
voltage power supply network
that supplies buildings used for
domestic purposes.
Harmonic
emissions IEC
61000-3-2
Not
applicable
Voltage
fluctuations/
Flicker
emissions IEC
61000-3-3
Not
applicable
Immunity Test IEC
60601Test
Level
Complia
nce
Level
Electromagnetic
Environment -
Guidance
Electrostatic
discharge
(ESD)IEC
61000-4-2
± 8 kV
contact
± 2 kV,
± 4 kV,
± 8 kV,
± 15 kV air
± 8 kV
contact
± 2 kV,
± 4 kV,
± 8 kV,
± 15 kV
air
Floors should be wood,
concrete, or ceramic
tile. If floors are
covered with synthetic
material, the relative
humidity should be at
least 30%
Power
frequency(50
Hz/60Hz)mag
netic field IEC
61000-4-8
30 A/m 30 A/m Magnetic fields from
common appliances
are not expected to
affect the device.
NOTE: UT is the a.c. mains voltage prior to application of the
test level
Radiated
RFIEC
61000-4-3
10V/m
80MHz to
2.7GHz
9V/m,
27V/m,
28V/m
385-5785
MHz
10V/m
80MHz
to
2.7GHz
9V/m,
27V/m,
28V/m
385-578
5
MHz
Portable RF
communications
equipment (including
peripherals such as
antenna cables and
external antennas)
should be used no
closer than 30 cm (12
inches)to any part of
this device, including
cables specified by the
manufacturer.
Otherwise, degradation
of the performance of
this equipment could
result.
SPECIFICATIONS
1 Model BD-4610
2 Measurement
Method Oscillometric
3 Display LCD
4 Measurement
Range Pressure: 0 to 299 mmHg
Pulse: 40 to 180 beats/minute
5 Accuracy Pressure: Within ± 3 mmHg
Pulse Rate: Within ± 5% of reading
6 Inflation Automatic inflation by pump
7 Deflation Automatic rapid deflation
8 Pressure Detection Semiconductor pressure sensor
9 Memory 2 persons X 90 measurements each
1
0 Power Supply 2 AAA alkaline batteries (not included)
1
1 Battery Life About 6 months when used once a
day
1
2Operating
Environment Temperat
ure 50°F (10°C) to 104°F
( 40°C)
Humidity 15% to 90%
(noncondensing)
Barometri
c
Pressure
105 kPa to 80 kPa (790
mmHg to 600 mmHg)
1
3Transport
Storage
Environment
Temperat
ure -4°F (-20°C) to 131°F
( 55°C)
Humidity 0% to 95%
(noncondensing)
1
4 Weight of Main Unit Approximately 95 g (not including
batteries)
1
5External
Dimensions 65 mm (H) X 61 mm (W) X 28 mm (D)
(not including the wrist cuff)
1
6Measurable
Circumference of
Wrist
Approximately 5.3” ~ 8.5” (13.5cm ~
21.5 cm)
1
7Electric Shock
Protection Internal power supply appliance type
BF
Symbols Use
SYMBOLS USED IN THIS INSTRUCTION MANUAL
Type BF applied part
The marking of electrical and electronics
devices according to Directive 2012/19/EU.
The device, accessories and the packaging
have to be disposed of waste correctly at the
end of the usage.
ENVIRONMENT
This appliance should not be put into the domestic
garbage at the end of its durability, but must be offered at a
central point for the recycling of electric and electronic
domestic appliances. This symbol on the appliance, instruction
manual and packaging puts your attention to this important
issue. The materials used in this appliance can be recycled. By
recycling of used domestic appliances you contribute an
important push to the protection of our environment. Ask your
local authorities for information regarding the point of
recollection.
BATTERIES
The European directive for batteries (2006/66/EC) states that it
is not permitted to throw batteries away with the household
waste. They may contain substances which are harmful to the
environment. Empty batteries can be handed over to a local,
public collection point or a local recycling centre. To avoid
overheating as a result of a short circuit, lithium batteries must
be removed from the product and the poles must be protected
using insulation tape or some other means against short-
circuiting.
PTManual de Instruções
SEGURANÇA
DECLARAÇÃO DE EXONERAÇÃO DE RESPONSABILIDADE
MÉDICA Este aparelho e respetivo manual não substituem o
conselho de um médico ou outro profissional de saúde.
Contacte o seu médico para interpretar os valores das
medições ou se tem ou suspeita ter um problema médico.
• Se não seguir as instruções de
segurança, o fabricante não pode ser
considerado responsável pelo danos.
• Não se destina a ser usado por
crianças, mulheres grávidas ou doentes
com pré-eclampsia.
• Uma insuflação excessiva prolongada
do monitor resultará na lesão do doente.
• Não use este aparelho sobre uma
ferida, pois pode agravar a lesão.
• Medições demasiado frequentes podem
provocar lesões devido à interferência
sobre o fluxo sanguíneo.
• Não tente modificar de forma alguma
este aparelho.
• Nunca desloque o aparelho puxando
pelo cabo e certifique-se de que este
nunca fica preso.
• O aparelho deve ser colocado numa
superfície plana e estável.
• Este produto destina-se apenas a uso
doméstico. Não se destina a substituir a
consulta do seu médico.
• O aparelho poderá não ser adequado
para utilizadores diagnosticados com
arritmia comum (batimentos atriais ou
ventriculares prematuros ou fibrilação
atrial), diabetes, má circulação
sanguínea, problemas renais ou para
utilizadores que tenham sofrido um AVC
ou que se encontrem inconscientes. Em
caso de dúvida, consulte o seu médico.
• A unidade não deve ser manuseada por
crianças para evitar situações
perigosas.
• A unidade contém módulos de alta
precisão. Por este motivo, evite expô-la
a temperaturas extremas, humidade e
radiação solar direta. Evite a queda ou
pancadas fortes na unidade principal e
proteja-a do pó.
• As baterias com derrame podem
danificar a unidade. Remova as baterias
se a unidade não for utilizada durante
um longo período.
• Se guardar a unidade num local frio,
deixe-a aclimatizar-se à temperatura
ambiente antes de usar.
• Para evitar resultados incorretos
provocados pela interferência
eletromagnética entre equipamento
elétrico e eletrónico, não use o aparelho
próximo de um telemóvel ou de um
forno microondas.
• Para se proteger contra choques
elétricos, não mergulhe o cabo, a ficha
nem o aparelho em água ou qualquer
outro líquido.
• Este aparelho não deve ser usado por
crianças. Este aparelho pode ser
utilizado por pessoas com capacidade
física, sensorial ou mental reduzida ou
com falta de experiência e
conhecimento, se forem
supervisionadas ou tiverem recebido
instruções relativas à utilização do
aparelho de forma segura e
compreenderem os riscos envolvidos.
As crianças não devem brincar com o
aparelho. Mantenha o aparelho e o
respetivo cabo de alimentação fora do
alcance das crianças. A limpeza e
manutenção não devem ser efetuadas
por crianças.
SEGURANÇA DAS PILHAS
• Não exponha a pilha a temperaturas
elevadas ou luz solar direta. Nunca atire
as pilhas para uma fogueira. Existe
perigo de explosão!
• Mantenha as pilhas afastadas das
crianças. As pilhas não são brinquedos!
• Não abra as pilhas à força.
• Evite o contacto com objetos metálicos
(anéis, pregos, parafusos etc.); existe o
perigo de curto-circuito!
• Em resultado de um curto-circuito, as
pilhas podem aquecer
consideravelmente ou mesmo incendiar.
Isto poderá resultar em queimaduras.
• Para sua segurança, os polos das
pilhas deverão ser cobertos com fitas
adesivas durante o transporte.
• Não toque numa pilha com ruturas e/ou
com fugas. Se o líquido da pilha entrar
em contacto com os seus olhos, lave-os
o mais rapidamente possível com água
limpa, sem esfregar os olhos. Dirija-se
imediatamente ao hospital. Se não for
devidamente tratado, poderá resultar
em problemas oculares.
TENSÃO ARTERIAL
O que é a tensão arterial?
A tensão arterial é a pressão que o fluxo de sangue exerce
sobre a parede das artérias. A tensão arterial sistólica
(máxima) é medida quando o coração contrai e expulsa o
sangue para fora do coração. A tensão arterial diastólica
(mínima) é medida quando o coração dilata e o sangue flui de
volta para o coração.
Porquê medir a tensão arterial?
Entre os diversos problemas de saúde que hoje mais afetam
as pessoas, as questões associadas com a hipertensão
arterial são, de longe, as mais comuns. A correlação
perigosamente forte entre a hipertensão arterial e as doenças
cardiovasculares e a elevada taxa de morbilidade tornaram a
medição da tensão arterial uma necessidade para identificar
os indivíduos em situação de risco.
Tensão arterial padrão.
A Organização Mundial da Saúde (OMS) e o National High
Blood Pressure Education Program desenvolveram um padrão
de tensão arterial que permite identificar áreas de baixa e alta
tensão. Contudo, este padrão é apenas uma orientação geral,
pois a tensão arterial dos indivíduos varia consoante as
pessoas, grupos, etc.
É importante consultar regularmente o seu médico. O médico
dirá quais são os limites da sua tensão arterial normal, bem
como o ponto a partir do qual poderá estar em situação de
risco.
Flutuação da tensão arterial
A tensão arterial está sempre a flutuar!
Não se deve preocupar se obtiver dois ou três valores de
tensão arterial elevados.
A tensão arterial muda ao longo do mês e até mesmo do dia,
dependendo das circunstâncias (estado de espírito,
temperatura, ...).
Os valores de tensão arterial determinados com este aparelho
são equivalentes aos obtidos por um observador formado
usando o método auscultatório do punho/estetoscópio, dentro
dos limites prescritos pela revisão do Protocolo Internacional
da Sociedade Europeia de Hipertensão, de 2010, para a
validação dos aparelhos de medição da tensão arterial em
adultos.
Um batimento cardíaco irregular (IHB) é definido como um
batimento mais de 25% mais lento ou 25% mais rápido do que
o batimento médio detetado enquanto o aparelho mede a
tensão arterial sistólica e a tensão arterial diastólica. Quando o
aparelho deteta um batimento irregular duas ou mais vezes
durante a medição, o Símbolo de Batimento Cardíaco Irregular
é exibido com os valores obtidos na medição.
DESCRIÇÃO DAS PEÇAS
1. Visor
2. Botão start/stop
3. Botão de memória
4. Braçadeira de punho
Visor
1. Tensão arterial sistólica
2. Tensão arterial diastólica
3. Frequência cardíaca
4. Memória
5. Pilha fraca
6. Pulso detetado
7. IHB
8. Data/hora
9. Número de utilizador
ANTES DA PRIMEIRA UTILIZAÇÃO
• Retire o aparelho e os acessórios da caixa.Retire os
autocolantes, a película ou plástico de proteção do aparelho.
Instalação das pilhas:
1. Puxe para baixo a tampa do compartimento das pilhas que
se encontra do lado esquerdo do aparelho.
2. Insira duas pilhas alcalinas AAA de acordo com os sinais +
e –.
3. Feche a tampa do compartimento tendo o cuidado de
garantir que encaixa bem. Certifique-se de que a tampa do
compartimento das pilhas está na posição certa.
4. NOTA: Quando o símbolo de pilha fraca aparecer no visor,
desligue o aparelho e siga as instruções acima para
substituir as pilhas.
Programar o utilizador, ano, data e hora:
1. Se o aparelho já estiver ligado imediatamente após a
instalação das pilhas, alterne entre User 1 (Utilizador 1) e
User 2 premindo o botão “START/STOP”. Se o aparelho
estiver desligado, prima e mantenha 2 segundos nesta
posição o botão “MEM”; depois, alterne entre User 1 e
User 2 premindo o botão “START/STOP”. Para selecionar
o utilizador, prima “MEM” para confirmar e os dígitos
relativos ao ano começam a piscar.
2. Prima “START/STOP” para avançar um ano ou prima e
mantenha nesta posição “START/STOP” para avançar
vários anos. Prima “MEM” para confirmar e os dígitos
relativos ao mês começam a piscar.
3. Prima “START/STOP” para avançar um mês ou prima e
mantenha nesta posição “START/STOP” para avançar
vários meses. Prima “MEM” para confirmar e os dígitos
relativos ao dia começam a piscar.
4. Prima “START/STOP” para avançar um dia ou prima e
mantenha nesta posição “START/STOP” para avançar
vários dias. Prima “MEM” para confirmar e os dígitos
relativos à hora começam a piscar.
5. Prima “START/STOP” para avançar uma hora ou prima e
mantenha nesta posição “START/STOP” para avançar
várias horas. Prima “MEM” para confirmar e os dígitos
relativos aos minutos começam a piscar.
6. Prima “START/STOP” para avançar um minuto ou prima e
mantenha nesta posição “START/STOP” para avançar
vários minutos. Prima “MEM” para confirmar e o aparelho
desliga-se.
UTILIZAÇÃO
Antes de medir a tensão
• Para obter resultados mais precisos, as medições devem ser
efetuadas nas mesmas circunstâncias e à mesma hora,
todos os dias.
• Este aparelho pode ser aplicado em qualquer pulso, mas de
preferência no esquerdo. Use o mesmo pulso em cada
medição.
• Qualquer registo da tensão arterial pode ser afetado pela
posição e condição física do indivíduo, bem como por outros
fatores, como ruído de fundo, stress, fala, movimento do
corpo, etc.
• Evite efetuar a medição se estiver sob tensão.
• Não deve comer, beber álcool, fumar, fazer exercício ou
tomar banho 30 minutos antes de utilizar este aparelho, pois
estas atividades podem alterar a tensão arterial.
• Para uma indicação precisa da tensão arterial real, faça e
registe várias medições durante um determinado período de
tempo.
• Se deseja efetuar medições consecutivas, aguarde dois
minutos entre medições para permitir que o sangue circule
pelo braço normalmente.

Produktspezifikationen

Marke: Tristar
Kategorie: Blutdruckmessgerät
Modell: BD-4610

Brauchst du Hilfe?

Wenn Sie Hilfe mit Tristar BD-4610 benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten


Bedienungsanleitung Blutdruckmessgerät Tristar

Tristar

Tristar BD-4611 Bedienungsanleitung

7 August 2024
Tristar

Tristar PD-8878 Bedienungsanleitung

7 Juli 2024
Tristar

Tristar BD-4610 Bedienungsanleitung

7 Juli 2024

Bedienungsanleitung Blutdruckmessgerät

Neueste Bedienungsanleitung für -Kategorien-

Medisana

Medisana BPW 300 Bedienungsanleitung

16 Oktober 2024
Cresta

Cresta BPM701 Bedienungsanleitung

4 Oktober 2024
Medel

Medel Palm Self Bedienungsanleitung

28 September 2024
Medel

Medel Dualstetho PRO Bedienungsanleitung

28 September 2024
Medel

Medel Stetho Self Bedienungsanleitung

28 September 2024
Medel

Medel Sense Bedienungsanleitung

28 September 2024
Bioland

Bioland 2006 Bedienungsanleitung

17 September 2024
Medisana

Medisana SL 100 Connect Bedienungsanleitung

17 September 2024
König

König HC-BLDPRESS13 Bedienungsanleitung

15 September 2024
Thomson

Thomson TBPI-801W Bedienungsanleitung

12 September 2024