Tripp Lite TLNETCARD Bedienungsanleitung

Tripp Lite UPS TLNETCARD

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Tripp Lite TLNETCARD (44 Seiten) in der Kategorie UPS. Dieser Bedienungsanleitung war für 17 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Seite 1/44
User’s Guide
TLNETCARD
Documentation Notice: This User’s Guide is a supplement to the printed manual that came with your TLNETCARD or network-enabled
Tripp Lite device. Refer to the printed manual for instructions on hardware installation and basic conguration, including IP address assignment.
If you have misplaced your printed manual, refer to the downloadable electronic version by going to www.tripplite.com/support and entering
TLNETCARD in the search window.
1. Introduction ........................................................2
1.1 System Requirements 2 ....................................
2. Installation and Configuration 3 ............................
2.1 SNMP Configuration 3 ........................................
2.1.1 Configuring with TLNET Configurator 3 ............
2.1.2 Configuring via TLNET Supervisor 4 ................
2.1.3 Configuring via Telnet 5 ................................
2.1.4 Configuring via Text Mode 6 ..........................
2.1.5 Configuring through COM Port 9 ....................
3. TLNET Supervisor 10 ...............................................
3.1 Monitor .........................................................10
3.1.1 Information 10 ............................................
3.1.2 History 13 ...................................................
3.1.3 Environment 14 ...........................................
3.1.4 About 15 ....................................................
3.2 Devices.........................................................15
3.2.1 Management.......................................... 15
3.3 System .........................................................19
3.3.1 Administration 19 ........................................
3.3.2 Notification 24 ............................................
4. TLNET Configurator 27 ............................................
4.1 Batch Configuration 27 ......................................
4.2 Batch Upgrade 29 ..............................................
5. Modbus TCP 31 .......................................................
5.1 Configuration ................................................31
5.2 Operation......................................................32
6. Troubleshooting 40 ..................................................
Appendix A – Default System Settings 42 ...................
Appendix B – Default SNMP Settings 43 ......................
Table of Contents
1111 W. 35th Street, Chicago, IL 60609 USA • www.tripplite.com/support
Copyright © 2016 Tripp Lite. All rights reserved. All trademarks are the sole property of their respective owners.
2
TLNETCARD is an optional network card you can install in the accessory slot of a compatible UPS system. TLNETCARD connects your Tripp Lite
device to your Ethernet network for remote monitoring, control and condition reporting. You can manage the device from an SNMP Network
Management Station, a Web browser or telnet. The TLNETCARD can also send SNMP traps or email messages to the addresses you specify,
alerting you automatically to events such as power failures.
1.1 System Requirements
Tripp Lite UPS system with compatible accessory slot.
Ethernet network that supports the TCP/IP protocol. Firewall ports 3664 and 3665 may need to be opened.
One of the following options for remote monitoring and control:
SNMP-based Network Management Station (such as HP® OpenView®)
Web browser
VT-100 Telnet and/or SSH Client
For “Terminal Mode” configuration only:
Terminal emulation software program (such as TeraTerm Pro by Ayera Technologies)
Computer with available DB9 serial port
Warning: Use of this equipment in life support applications where failure of this equipment can reasonably be expected to cause the failure of the
life support equipment or to significantly affect its safety or effectiveness is not recommended. Do not use this equipment in the presence of a
flammable anesthetic mixture with air, oxygen or nitrous oxide.
1. Introduction
3
For instructions on hardware installation, refer to the printed manual that came with your TLNETCARD.
2.1 SNMP Configuration
There are multiple ways to configure the TLNETCARD:
TLNET Configurator: Use the downloadable program TLNET Configurator to quickly set up one or more TLNETCARDs over the network. Refer
to Section 2.1.1 for more information.
Web-based Interface: Individual TLNETCARDs can be configured over the network through their TLNET Supervisor interfaces. Refer to
Section 2.1.2 for more information.
Telnet Mode: Configure the TLNETCARD over the network in text mode. Refer to Section 2.1.4 for more information.
If a network connection is not available, the TLNETCARD can be configured through its COM port. Please refer to COM Port: Section 2.1.5
for more information.
Notes:
When initially connected to the network, the TLNETCARD will attempt to obtain an IP address via DHCP. If DHCP is disabled on the network, the TLNETCARD
can be accessed using its default IP address: 192.168.1.100.
To ensure system security, it is highly recommended that the account and password be changed after the first login.
If multiple TLNETCARDs are installed on the network, it is advisable to change the TLNETCARD's default Host Name to avoid conflicts. Likewise, it is
recommended to disable BOOTP/DHCP and manually assign a valid static IP address to the TLNETCARD.
2.1.1 Configuring with TLNET Configurator
The following instructions refer to the TLNETCARD Congurator utility software. The TLNETCARD Configurator can be
downloaded at tripplite.com/support and typing TLNETCARD in the search field.
The TLNET Configurator utility (compatible with Windows 2000/2003/2008/XP/Vista/7) enables easy
configuration and firmware upgrade of one or more TLNETCARDs. Follow the instructions below:
Step 1: Use a Cat5 cable to connect the TLNETCARD’s Network port to the network.
Step 2: Ensure the two DIP switches of the TLNETCARD are set to the OFF position (Normal Mode) to enable network
communication and that the workstation and the TLNETCARD are on the same LAN
Step 3: Once downloaded, launch TLNET Configurator.
Step 4: Click Discover to search all available SNMP devices on the LAN. A list of devices will be shown.
Notes:
To search for SNMP devices in a different domain, change the Subnet and IPv4 IPv6 Prefix Length and click Discover.
If the TLNETCARD cannot be found, verify that UDP port 3456 on the workstation is open.
2. Installation and Configuration


Produktspezifikationen

Marke: Tripp Lite
Kategorie: UPS
Modell: TLNETCARD

Brauchst du Hilfe?

Wenn Sie Hilfe mit Tripp Lite TLNETCARD benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten




Bedienungsanleitung UPS Tripp Lite

Bedienungsanleitung UPS

Neueste Bedienungsanleitung für -Kategorien-