Tripp Lite SRSWITCH Bedienungsanleitung


Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Tripp Lite SRSWITCH (4 Seiten) in der Kategorie Nicht kategorisiert. Dieser Bedienungsanleitung war für 24 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Seite 1/4
Owner’s Manual
SmartRackâ„¢ Accessories
Model: SRSWITCH
1111 W. 35th Street, Chicago, IL 60609 USA
(773) 869-1234 • www.tripplite.com
Copyright © 2008 Tripp Lite. All rights reserved.
WARRANTY
REGISTRATION:
register online today for a
chance to win a FREE Tripp Lite
product—www.tripplite.com/warranty
1 – Introduction 0 2
1-1 Parts List 2
1-2 Tools Required 2
2 – Important Safety Instructions 2
3 – SRSWITCH Installation 3
3-1 Mounting the Switch and Magnet to the Rack Enclosure 3
3-2 Wiring the Switch 3
4 – Connection to SNMPWEBCARD and ENVIROSENSE 4
5 – Warranty and Warranty Registration 4
2
2 – Important Safety Instructions
SAVE THESE INSTRUCTIONS
This manual contains instructions and warnings that must be followed during the installation and operation of the products
described in this manual. Read all instructions and warnings thoroughly before attempting installation. Failure to comply may
invalidate the warranty and cause property damage and/or personal injury.
1 – Introduction
1-1 Parts List
1-2 Tools Required
The SRSWITCH is designed to monitor rackmount enclosure door access and notify users when a door has been opened. The SRSWITCH must be used
together with the following Tripp Lite accessories: SNMPWEBCARD and ENVIROSENSE (both available separately).
A1 Switch (1)
A2 Magnet (1)
A3 #22 AWG cable - 6 ft. (1.8 m) (1)
A4 Cable ties (6)
A5 Adhesive cable tie holders (3)
Install in a controlled indoor environment, away from moisture, temperature extremes, ammable liquids and gasses, conductive contaminants, dust and •
direct sunlight.
Provide suitable grounding in accordance with all applicable electrical wiring regulations.•
Use of this equipment in life support applications where failure of this equipment can reasonably be expected to cause the failure of the life support •
equipment or to signicantly affect its safety or effectiveness is not recommended. Do not use this equipment in the presence of a ammable anesthetic
mixture with air, oxygen or nitrous oxide.
A1
A2
A3
A4
A5
Wire Cutters Wire Strippers Screwdriver
3
3 – SRSWITCH Installation
The switch and magnet are designed to be mounted at the top of a SmartRack Premium Rack Enclosure. Magnet should be mounted ush against the inside
edge of the Rack Enclosure door. Attach the switch to the outside of the Rack Enclosure cabinet and make sure both switch and magnet are in alignment.
The switch and magnet should be mounted on the side of the enclosure opposite the hinges.
Note: the switch and magnet do not need to make physical contact but should be no more than ¼ inch (6.35 mm) apart.
3-1 Mounting the Switch and Magnet to the Rack Enclosure
3-2 Wiring the Switch
The double-sided tape on both the switch and magnet allow you to mount
them to a rack enclosure without any drilling.
Mark the intended location of both the switch and the magnet.1.
Peel the paper backing off the adhesive strip attached to the back 2.
of the switch.
Place the switch in the desired location. Press îš¿rmly.3.
Repeat steps 2 and 3 to mount the magnet.4.
Before attaching the wire to the switch, use wire cutters to clip to 1.
desired length (if necessary).
Use wire strippers to cut back the covering of the two wires and remove 2.
a small amount of insulation from the end of each wire. (Do not cut
through the insulation into the wire itself.)
Twist the bare ends of the wire, place them under the head of each 3.
screw on the switch and then wrap the wire clockwise around the screw.
Tighten the screw by turning it clockwise.
Use the cable ties and adhesive cable tie holders (included) to secure 4.
the entire length of the wire.
Route the wire away from the switch and magnet and attach to one of 5.
the security inputs on the ENVIROSENSE (see Section 4-1).
Note: Make sure the wire is not pinched by any part of the rack
enclosure or its door.
Approximately 1 in. (25.4 mm)
Approximately 0.38 in. ( )9.7 mm
SmartRack Enclosure
(Front Door Open)
Magnet: Attaches to Door
SmartRack Enclosure
(Back Door Open)
MagnetSwitch
Right Wrong
Switch: Attaches to Cabinet
Switch: Attaches to Cabinet
Magnet: Attaches to Door


Produktspezifikationen

Marke: Tripp Lite
Kategorie: Nicht kategorisiert
Modell: SRSWITCH
Breite: 100 mm
Tiefe: 24 mm
Produktfarbe: Black, White
Höhe: 33.5 mm
Verpackungsbreite: 100.1 mm
Verpackungstiefe: 143 mm
Verpackungshöhe: 55.1 mm
Paketgewicht: 230 g
Warentarifnummer (HS): 8536.50.9065
Ursprungsland: China
Anzahl Produkte pro Versandkarton: 50 Stück(e)
Gewicht Versandkarton: 12250 g
Länge des Versandkartons: 522 mm
Breite des Versandkartons: 307.1 mm
Höhe des Versandkartons: 303 mm
Hauptkarton GTIN (EAN/UPC): 10037332144772

Brauchst du Hilfe?

Wenn Sie Hilfe mit Tripp Lite SRSWITCH benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten




Bedienungsanleitung Nicht kategorisiert Tripp Lite

Bedienungsanleitung Nicht kategorisiert

Neueste Bedienungsanleitung für -Kategorien-