Tripp Lite SRGROUND25 Bedienungsanleitung


Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Tripp Lite SRGROUND25 (16 Seiten) in der Kategorie Nicht kategorisiert. Dieser Bedienungsanleitung war für 10 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Seite 1/16
Owner’s Manual
Copper Bus Grounding Bar
Models: SRGROUND, SRGROUND25
WARRANTY REGISTRATION
Register your product today and be
automatically entered to win an ISOBAR®
surge protector in our monthly drawing!
tripplite.com/warranty
1111 W. 35th Street, Chicago, IL 60609 USA • tripplite.com/support
Copyright © 2020 Tripp Lite. All rights reserved.
Español 6 • Français 11
2
Important Safety Instructions
SAVE THESE INSTRUCTIONS
This manual contains instructions and warnings that must be followed during the installation and operation of this product. Failure to comply
may invalidate the warranty.
The instructions in this manual are for common rack and rack enclosure types and may not be appropriate for all mounting applications.
You must determine the fitness of hardware and procedures before mounting.
Use of this equipment in life support applications where failure of this equipment can reasonably be expected to cause the failure of the life
support equipment or to significantly affect its safety or effectiveness is not recommended.
Introduction
The SRGROUND and SRGROUND25 grounding bar are comprised of a thin strip of copper that attaches to standard EIA-310-D rack enclosures
or open frame racks to provide convenient ground contact for standard rack-mount equipment. The SRGROUND fits into 42U or 48U racks or
enclosures. The SRGROUND25 fits into standard 24U or 25U racks or enclosures.
Parts List
45” (1.1 m) Grounding Bar
(with attached grounding lug)
Mounting Buttons
(x2)
Grounding Straps
(x13)
M4 Self
Tapping
Screws (x2)
M4 Screws
(x13)
Washers
(x13)
Cage
Nuts
(x2)
M6x12
Screws
(x2)
7’ (2.1 m) Grounding Bar
(with attached grounding lug)
Mounting Buttons
(x3)
Grounding Straps
(x21)
M4 Self-Tapping
Screws (x3)
M4 Screws
(x21)
Washers
(x21)
SRGROUNDSRGROUND25
1
2
4
42U
3
Installation
Rack Enclosures
1 , such as Tripp Lite’s SR42UB, attach the For a 42U enclosure
SRGROUND to the 3 indexed horizontal beams at the top, middle
and bottom of the enclosure. The included M4 Self-Tapping
Screws will go through the three clearance holes (non-threaded)
on the bar, and then into the beams of the rack enclosure.
, such as Tripp Lite’s SR48UB, attach the For a 48U enclosure
SRGROUND to the top and middle horizontal beams only, as the
bar will not reach all the way down to the bottom beam.
, such as Tripp Lite’s SR25UB, attach the For a 25U enclosure
SRGROUND25 to the 2 indexed horizontal beams at the top
and bottom of the enclosure, using the top and second from
the bottom holes. The included M4 Self-Tapping Screws will go
through the two clearance holes (non-threaded) on the bar, then
into the beams of the rack enclosure.
, such as Tripp Lite’s SR24UB, attach For a 24U enclosure
the SRGROUND25 to cage nuts installed in the top and bottom
horizontal rails of the enclosure using the top and bottom holes
of the SRGROUND25.
Note: The instructions above are specific for mounting in Tripp Lite SR42UB,
SR48UB, SR24UB or SR25UB SmartRack™ Enclosures. Mounting in other
enclosure brands is possible, but will vary depending upon the application.
Several holes are provided along the grounding bar that will allow for a workable
installation into any brand’s rack configuration.
Note: Placement will vary and depend on your particular rack configuration. It is
recommended to measure the distance between the bar and your equipment to
accommodate the length of the Grounding Straps. Once the length you need has
been determined, attach the bar in the appropriate holes in the horizontal beams.
2 Attach one end of the Grounding Strap to the bar using the
included M4 screws and washers.
3 Attach the other end of the Grounding Strap to the grounding
provision on the intended equipment.
4 Finally, attach your facility’s system ground to the grounding lug at
the bottom of the bar. The lug can accommodate 2/0-14AWG wires. FACILITY GROUND


Produktspezifikationen

Marke: Tripp Lite
Kategorie: Nicht kategorisiert
Modell: SRGROUND25
Breite: 15.9 mm
Tiefe: 6.4 mm
Gewicht: 1360 g
Produktfarbe: Kupfer
Höhe: 1148.1 mm
Verpackungsbreite: 85.1 mm
Verpackungstiefe: 59.9 mm
Verpackungshöhe: 1240 mm
Paketgewicht: 1360 g
Warentarifnummer (HS): 7409.19.1000
Ursprungsland: China
Typ: Erdungsschiene
Menge pro Packung: 1 Stück(e)
Gehäusematerial: Kupfer
Montageset: Ja
Anzahl Produkte pro Versandkarton: 10 Stück(e)
Gewicht Versandkarton: 15880 g
Länge des Versandkartons: 1260.1 mm
Breite des Versandkartons: 460 mm
Höhe des Versandkartons: 140 mm
Hauptkarton GTIN (EAN/UPC): 10037332241471
Rack-Kapazität: 25U

Brauchst du Hilfe?

Wenn Sie Hilfe mit Tripp Lite SRGROUND25 benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten




Bedienungsanleitung Nicht kategorisiert Tripp Lite

Bedienungsanleitung Nicht kategorisiert

Neueste Bedienungsanleitung für -Kategorien-