Tripp Lite SMARTINT1500 Bedienungsanleitung


Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Tripp Lite SMARTINT1500 (28 Seiten) in der Kategorie Nicht kategorisiert. Dieser Bedienungsanleitung war für 8 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Seite 1/28
Owner’s Manual
SmartProÂŽ INT
450-1500 VA
Intelligent, Line-Interactive
UPS Systems (230V)
1111 W. 35th Street, Chicago, IL 60609 USA • www.tripplite.com/support
Copyright Š 2019 Tripp Lite. All rights reserved. SmartPro
ÂŽ is a registered trademark of Tripp Lite.
Safety: 2
Quick Installation 3
Basic Operation 4
Storage & Service 6
Specications 6
EspaĂąol 7
Français 14
РусскиК 21
18-08-320-932202.indb 1 5/13/2019 2:55:51 PM
2
Safety
This manual contains important instructions and warnings that should be followed during the
installation, operation and storage of all Tripp Lite UPS Systems.
UPS Location Warnings
• Install your UPS indoors, away from excess moisture or heat, dust or direct sunlight.
• For best performance, keep the indoor temperature between 0° C and 40° C (between
32° F and 104° F).
• Leave adequate space around all sides of the UPS for proper ventilation.
UPS Connection Warnings
• Connect your UPS to a properly grounded AC power outlet. Do not modify the UPS’s plug.
Do not use adapters that eliminate the UPS’s ground line.
• Do not plug your UPS into itself; this will damage the UPS and void your warranty.
• If you are connecting your UPS to a motor-powered AC generator, the generator must
provide clean, ltered computer-grade output.
Equipment Connection Warnings
• Do not use Tripp Lite UPS Systems for life support applications in which a malfunction or
failure of a Tripp Lite UPS System could cause failure or signicantly alter the performance
of a life-support device.
• Do not connect surge suppressors to the output of your UPS. This may damage your UPS
and will void both the surge suppressor and UPS warranties.
Battery Warnings
• Your UPS does not require routine maintenance. Do not open your UPS for any reason.
There are no user-serviceable parts inside.
• Battery replacement must be performed by qualified service personnel. Because the
batteries present a risk of electrical shock and burn from high short-circuit current, qualied
service personnel should observe proper precautions: Unplug and turn off the UPS before
performing battery replacement. Use tools with insulated handles and replace the existing
batteries with the same number and type of new batteries (Sealed Lead-Acid). Do not open
the batteries. Do not short or bridge the battery terminals with any object.
• The UPS batteries are recyclable. Refer to local codes for disposal requirements. Do not
dispose of the batteries in a re.
• Do not attempt to add external batteries.
18-08-320-932202.indb 2 5/13/2019 2:55:51 PM
3
Quick Installation
1 Connect your computer to the UPS, and
the UPS to an electrical outlet.
1. Unplug your computer’s power cord from both
your AC outlet and your computer’s AC input.
2. Insert the female plug of the power cord that
came with your UPS A into your computer’s AC
input. Insert the UPS cord’s male plug into any of
your UPS’s female output receptacles.
3. Insert the female plug of your computer’s cord
B into your UPS’s AC input. Insert the male plug
of your computer’s cord into your AC outlet.
2 Plug your equipment into your UPS.
Your UPS is designed to support only computer
equipment. You will overload your UPS if you connect
household appliances, laser printers or surge
suppressors.
Cords and receptacle adapters are available
from Tripp Lite to accommodate most outlet
congurations. If rewiring is necessary, refer to the
Wire Color-Code Chart at the bottom of the page.
–Optional DB9 Connection*–
Using Tripp Lite cable, connect the serial port of
your computer to the serial port of your UPS. Load
software and run installation program appropriate to
your operating system.
*Your UPS will function properly without this connection.
3 Turn your UPS ON.
Set the System Enable Switch (UPS back panel) to
“ON” (or “ENABLE/I”) 3a. This switch activates the
battery charger and microprocessor. The
“ ” light will flash until you engage the ON/Standby
Switch to activate the “ON” mode.
Engage the momentary ON/Standby Switch (UPS
front panel) and release it to activate the “ON” mode
and supply power to the UPS receptacles 3b .
1
2
3a
3b
A
B
Wire Color Wire 1 Wire 2 Wire 3
American Black White Green
European Brown Blue Green/Yellow
Wire Reference Wire 1 Wire 2 Wire 3
American Line 1 Neutral Ground
European Line 1 Line 2 or Neutral Ground
Black Brown
White Blue
Green Green/
Yellow
AMER EURO
18-08-320-932202.indb 3 5/13/2019 2:55:53 PM


Produktspezifikationen

Marke: Tripp Lite
Kategorie: Nicht kategorisiert
Modell: SMARTINT1500

Brauchst du Hilfe?

Wenn Sie Hilfe mit Tripp Lite SMARTINT1500 benĂśtigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten




Bedienungsanleitung Nicht kategorisiert Tripp Lite

Bedienungsanleitung Nicht kategorisiert

Neueste Bedienungsanleitung fĂźr -Kategorien-