Tripp Lite SMART3000RMOD2U Bedienungsanleitung
Tripp Lite
UPS
SMART3000RMOD2U
Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Tripp Lite SMART3000RMOD2U (16 Seiten) in der Kategorie UPS. Dieser Bedienungsanleitung war für 7 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet
Seite 1/16
Introduction 2
Features 3
Mounting 5
Quick Installation 7
Optional Installation 8
Basic Operation 9
Power Module Replacement 12
Battery Replacement 13
Storage 14
Service 14
Warranty 15
Warranty Registration 15
Owner’s Manual
SmartPro® Rackmount
Intelligent, Line-Interactive UPS System
Model: SMART3000RMOD2U
• 110/120/127V Sine Wave Input/Output • 3000VA
1111 W. 35th Street, Chicago, IL 60609 USA • (773) 869-1234 •www.tripplite.com
Copyright © 2008 Tripp Lite. All rights reserved. SmartPro
® is a registered trademark of Tripp Lite.
Not suitable for mobile applications.
Warranty
Registration:
register online today for a
chance to win a FREE Tripp Lite
product—www.tripplite.com/warranty
Español 17
Français 33
2
UPS Location Warnings
The UPS is extremely heavy. Use caution when lifting and installing.•
Install the UPS indoors, away from excess moisture or heat, direct sunlight, dust and conductive contaminants.•
Install the UPS in a structurally sound area. •
Only operate the UPS at indoor temperatures between 32° F and 104° F (between 0° C and 40° C). For best results, keep indoor temperatures •
between 62° F and 84° F (between 17° C and 29° C).
Leave adequate space around all sides of the UPS for proper ventilation. Do not obstruct its ventilation fans or openings.
•
Do not install the UPS near magnetic storage media, as this may result in data corruption.•
If you are installing the UPS in a stack configuration, always stack the power module above the battery module(s) if present.•
Do not mount unit with its front or rear panel facing down (at any angle). Mounting in this manner will seriously inhibit the unit's internal •
cooling, eventually causing product damage not covered under warranty.
UPS Connection Warnings
The power supply for this unit must be rated in accordance with the equipment nameplate. It also must be suitably grounded.•
Connect the UPS system only to a NEMA L5-30R receptacle (outlet).•
Connect the UPS to a properly grounded AC power source. Do not modify the input connection in a way that would eliminate the connection to •
ground.
Do not use adapters that eliminate the connection to ground.•
Do not connect the UPS input to its output; this will damage the UPS and void the warranty.•
If you are connecting the UPS to a motor-powered AC generator, the generator must provide filtered, frequency-regulated computer-grade output. •
Connecting the UPS to a generator will void its Ultimate Lifetime Insurance.
Equipment Connection Warnings
Use of this equipment in life support applications where failure of this equipment can reasonably be expected to cause the failure of the life support •
equipment or to significantly affect its safety or effectiveness is not recommended. Do not use this equipment in the presence of a flammable
anesthetic mixture with air, oxygen or nitrous oxide
The UPS is connected to a DC energy source (battery). The output terminals may be live even when the UPS is not connected to an AC power •
source.
Do not connect surge suppressors or extension cords to the output of the UPS. This might overload the UPS and will void the surge suppressor and •
UPS warranties.
Maintenance Warnings
The UPS does not require routine maintenance. Do not open the UPS for any reason. There are no user-serviceable parts inside.•
Battery Warnings
Connect only Tripp Lite battery packs to the battery connectors. Connect battery packs of the correct voltage and type.•
Batteries can present a risk of electrical shock and burn from high short-circuit current. Observe proper precautions. Do not dispose of the batteries •
in a fire. Do not open the UPS or batteries. Do not short or bridge the battery terminals with any object. Unplug and turn off the UPS before
performing battery replacement. Use tools with insulated handles. There are no user-serviceable parts inside the UPS. Battery replacement should be
performed only by authorized service personnel using the same number and type of batteries (Sealed Lead-Acid). The batteries are recyclable. Refer
to your local codes for disposal requirements or in the USA only call 1-800-SAV-LEAD or 1-800-8-BATTERY (1-800-822-8837) or visit
www.rbrc.com for recycling information. Tripp Lite offers a complete line of UPS System Replacement Battery Cartridges (R.B.C.).Visit Tripp Lite
on the Web at www.tripplite.com/support/battery/index.cfm to locate the specific replacement battery for your UPS.
Do not open or mutilate the batteries. Released electrolyte is harmful to the skin and eyes, and may be toxic.•
Fuses should be replaced only by factory-authorized personnel. Blown fuses should be replaced only with fuses of the same number and type.•
Service and repair should be performed only by trained personnel. During any service work to the UPS, it should be turned off.•
Do not connect or disconnect external battery pack(s) while the UPS is operating from the battery supply.•
During hot-swap battery pack replacement, the UPS will not provide backup power in the event of a blackout or other power interruption.•
SAVE THESE INSTRUCTIONS. This manual contains important instructions and warnings that should be followed
during the installation and maintenance of this UPS system.
Introduction
3
1
5
9
10
11
12
23
4
6
7
8
The SMART3000RMOD2U UPS System features a hot-swappable power module. When the bracket holding the power module in place is removed (there
is no manual bypass switch on the unit), the UPS automatically switches to “BYPASS” mode. This allows the power module to be removed for mainte-
nance, repair or replacement without disrupting power to connected loads. Review the location and function of the UPS system’s features before installing
and operating it.
1 “Load/Battery” Bar Graph: This display indicates the power load and battery levels.
2
“On” Button: Press this button and hold it for one second until you hear a beep to turn the UPS System ON. If the battery alarm is sounding,
press this button to silence it.
3 “Off/Standby” Button: Press this button and hold it for one second to turn the UPS system OFF.
4
“Load Level” LED (Green): This LED illuminates when the Load/Battery Bar Graph is displaying the load level.
5
“Battery Capacity” LED (Green): This LED illuminates when the Load/Battery Bar Graph is displaying the battery capacity.
6
“AC Mode” LED (Green): This LED illuminates when the UPS System is ON and supplying connected equipment with AC power from a utility
source.
7
“Automatic Voltage Regulation (AVR) Mode” LED (Yellow): This LED illuminates whenever the UPS system is lowering voltage and blinks
continuously when the UPS is boosting voltage.
8
“Overload” LED (Red): When this LED is illuminated, the load is >105%. Clear the overload immediately by unplugging some of your
equipment from the outlets until the LED changes from red to yellow (or green). CAUTION! Any overload that is not immediately corrected
by the user may cause the UPS to shut down and cease supplying output power in the event of a blackout or brownout.
9
“UPS Fault” LED (Red): This LED illuminates if the UPS system has an internal fault.
10
“Site Wiring Fault” LED (Red): This LED illuminates if the UPS system detects a site wiring problem.
11
“Battery Fault” LED (Yellow): This LED illuminates if the UPS system senses a weak, bad or disconnected battery.
12
“On Battery” LED (Green): This LED illuminates if the UPS system is operating from battery power.
Front Control Panel
Features
Produktspezifikationen
| Marke: | Tripp Lite |
| Kategorie: | UPS |
| Modell: | SMART3000RMOD2U |
Brauchst du Hilfe?
Wenn Sie Hilfe mit Tripp Lite SMART3000RMOD2U benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten
Bedienungsanleitung UPS Tripp Lite
9 Oktober 2024
9 Oktober 2024
4 Oktober 2024
2 Oktober 2024
29 September 2024
19 September 2024
10 September 2024
8 September 2024
30 August 2024
16 August 2024
Bedienungsanleitung UPS
- UPS Approx
- UPS Gembird
- UPS HP
- UPS Voltcraft
- UPS AEG
- UPS Siemens
- UPS IKEA
- UPS Dell
- UPS LC-Power
- UPS GYS
- UPS Adj
- UPS Block
- UPS Digitus
- UPS APC
- UPS CyberPower
- UPS Eaton
- UPS EnerGenie
- UPS Emerson
- UPS Furman
- UPS Riello
- UPS Puls Dimension
- UPS Avocent
- UPS Atlantis Land
- UPS Vanson
- UPS Phoenix Contact
- UPS Minuteman
- UPS V7
- UPS Equip
- UPS Salicru
- UPS SurgeX
- UPS Bxterra
- UPS Altronix
- UPS FSP
- UPS Ditek
- UPS PowerWalker
- UPS FSP/Fortron
- UPS East
- UPS Liebert
- UPS Murr Elektronik
- UPS Online USV
Neueste Bedienungsanleitung für -Kategorien-
13 Oktober 2024
13 Oktober 2024
13 Oktober 2024
13 Oktober 2024
13 Oktober 2024
13 Oktober 2024
13 Oktober 2024
13 Oktober 2024
11 Oktober 2024
5 Oktober 2024