Tripp Lite DNET1 Bedienungsanleitung


Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung fĂŒr Tripp Lite DNET1 (12 Seiten) in der Kategorie Nicht kategorisiert. Dieser Bedienungsanleitung war fĂŒr 22 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Seite 1/12
1
Owner’s Manual
Network Dataline
Surge Suppressors
Tripp Lite World Headquarters
1111 W. 35th Street, Chicago, IL 60609 USA
(773) 869-1234 ‱ www.tripplite.com
Note: Follow these instructions to ensure proper operation and prevent damage to this device
and its connected equipment.
Copyright © 2008 Tripp Lite. All rights reserved. All trademarks are the property of their respective owners.
Data Shieldℱ by Tripp Lite Network Dataline Surge Suppressors are designed to protect
data and communications equipment against AC transients caused by lightning, electrostatic
discharge and ground surges that can enter equipment from the signal lines or chassis ground.
Data Shield by Tripp Lite Network Dataline Surge Suppressors described here protect
networked equipment using 100Base-T, 10Base-T, 10Base-2 and Ethernet, Token Ring,
RS232, RS422, parallel, dial-up modems, fax, ISDN, DDS, T-1 and other communication
interfaces.
200810167 93-2858.indd 1 12/16/2008 9:58:50 AM
2
INSTALLATION
1. Make sure the computer, network device or other equipment is logged OFF the network
(if applicable). Turn OFF power to the equipment.
2. Disconnect the cable from the equipment to be protected.
3. Connect the Data Shield by Tripp Lite Network Dataline Surge Suppressor directly to the
equipment. DB9 and DB25 models are reversible, to work with male or female ports. To
change gender, remove the thumbscrews, reverse their direction and re-install.
4. Attach the green ground wire on the surge suppressor directly to the protected
equipment’s chassis. (Except DB9 and DB25 models.)
5. Reconnect the cable to the Data Shield by Tripp Lite Network Dataline Surge
Suppressor.
NOTE!
The Data Shield by Tripp Lite Network Dataline Surge Suppressor must be properly grounded and positioned as close
as possible to the equipment to be protected. For best results, it is required that the length of the signal line and ground
wire (if equipped) between the surge suppressor and the protected equipment be kept as short as possible, not to
exceed 12 inches (12”). It is best to install the surge suppressor directly to the equipment, as noted above.
NOTE!
Installing a typical Data Shield by Tripp Lite Network Dataline Surge Suppressor is equivalent to adding
approximately three feet (3’) of typical data communication cable to a segment.
CAUTION!
The Data Shield by Tripp Lite Network Dataline Surge
Suppressor does not protect the equipment on the opposite end
of the cable. Normally, protection at both ends is recommended.
CAUTION!
Use of this equipment in life support applications where failure
of this equipment can reasonably be expected to cause the
failure of the life support equipment or to signiïŹcantly affect its
safety or effectiveness is not recommended. Do not use this
equipment in the presence of a ïŹ‚ammable anesthetic mixture
with air, oxygen or nitrous oxide.
CAUTION!
When properly installed, the Data Shield by Tripp Lite Network
Dataline Surge Suppressor will only protect against surges on
the dataline portion of your installation. Simultaneous AC surge
suppression/power protection in the form of an ISOBARÂź surge
suppressor or Tripp Lite UPS system is strongly recommended
for complete system/network protection and can also extend
Ultimate Lifetime Insurance coverage to connected equipment.
200810167 93-2858.indd 2 12/16/2008 9:58:51 AM
3
SPECIFICATIONS
All surge suppressors listed have component response times of less than 1 picosecond.
Model: Description:
Nominal
Clamping Voltage:
Peak Pulse
Current:
DRS232 RJ45/RJ11 protector for
100Base-T4, RS232 on twisted Pair
(wires 1-8) or ISDN “S/T” interfaces.
Supplied with a 4” RJ45 patch cable.
18 volts, protecting
wires 1-8 1340 amps
DNET1
RJ45 100Base-T, 10Base-T,
Token Ring, RS422, AS400/Sys3x
protector for NICs, hubs, routers,
etc. Supplied with 4” RJ45 patch
cable.
7.5 volts, protecting
wires 1-8 750 amps
DSUT1CSU
RJ45/RJ11 protector for nonspan
powered T-1 equipment, digital data
service CSUs/DSUs, ISDN “U”
interfaces or other digital lines.
Supplied with 4” RJ45 patch cable.
60 volts, protecting
wires 1-8 200 amps
DTEL2 RJ45/RJ11 for modems, answering
and fax machines. Supplied with
4” RJ11 patch cable.
260 volts, protecting center
4 wires (2 CO-lines) 250 amps
DB9
Serial DB9 RS232 protector for male
or female ports of data terminal and
computing equipment including PCs,
modems, etc. (Any male or female
9-pin port). Male/Female genders
are reversible with reversible
thumbscrews.
18 volts, protecting pins
1-9 and chassis 340 amps
DB25
Serial DB25 RS232 protector
(wires 1-8, 20) for male or female
ports of data terminal & computing
equipment including PCs, printers,
modems, etc. Male/Female genders
are reversible with reversible
thumbscrews.
18 volts, protecting pins
1-8, 20 and chassis 340 amps
DB25-ALL DB25-ALL: Serial DB25 RS232
protector (pins 1-25) for any 25-pin
male or female DTE/DCE ports.
Male/Female genders are reversible
with reversible thumbscrews.
18 volts, protecting pins
1-25 and chassis 340 amps
D10B2 10Base-2 thin coax protector (BNC
m/f). Also protects IBM 3270 and
CCTV lines.
7.5 volts, protecting center,
shield and chassis 750 amps
DCATV
Coaxial protector for TVs, VCRs, pro
video supplied by CATV (“F” m/f).
7.5 volts, protecting center
and shield conductors 750 amps
Call Tripp Lite Customer Support at (773) 869-1234 for additional applications.
200810167 93-2858.indd 3 12/16/2008 9:58:51 AM


Produktspezifikationen

Marke: Tripp Lite
Kategorie: Nicht kategorisiert
Modell: DNET1

Brauchst du Hilfe?

Wenn Sie Hilfe mit Tripp Lite DNET1 benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten




Bedienungsanleitung Nicht kategorisiert Tripp Lite

Bedienungsanleitung Nicht kategorisiert

Neueste Bedienungsanleitung fĂŒr -Kategorien-