Tripp Lite APSX2012SW Bedienungsanleitung


Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Tripp Lite APSX2012SW (48 Seiten) in der Kategorie Nicht kategorisiert. Dieser Bedienungsanleitung war für 3 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Seite 1/48
Owner’s Manual
Sine Wave DC-to-AC Inverter/Chargers
Models: APSX1012SW, APSX2012SW
12VDC to 230VAC
1111 W. 35th Street, Chicago, IL 60609 USA
www.tripplite.com/support
Copyright © 2011 Tripp Lite. All rights reserved.
Table of Contents
Important Safety Instructions 2
1. Overview & Features 3
1.1 Overview 3
1.2 Indicators, Controls and Settings 3
1.3 Optional Features 6
2. Battery Charger 6
2.1 Mode of Operation 6
2.2 Transfer Switching Speed 6
3. Battery Installation
and Maintenance 6
3.1 Select Battery Type 6
3.2 Monthly Maintenance 8
3.3 Battery Installation 8
3.4 Battery Connection 8
4. Inverter/Charger
Installation and Operation 10
4.1 Installation 10
4.2 Installation Diagrams and Charts 10
4.3 Installation and Start-Up 11
5. Technical Specifications 11
6. Troubleshooting 12
7. Service 12
Español 13
Français 25
Ðóññêèé 37
201110117 93-3054.indb 1 11/9/2011 10:57:55 AM
2
Important Safety Instructions
SAVE THESE INSTRUCTIONS!
This manual contains important instructions and warnings that should be followed during the installation,
operation and storage of all Tripp Lite Inverter/Chargers.
Location Warnings
Install your Inverter/Charger in a location or compartment that minimizes exposure to heat, dust, direct sunlight and
moisture. Flooding the unit with water will cause it to short-circuit and could cause personal injury due to electric shock.
For proper ventilation, allow a minimum 2 inches of clearance at front and back of the Inverter/Charger. To avoid overheating
the Inverter, the compartment that houses the Inverter/Charger must be properly ventilated with adequate outside air flow.
The heavier the load of connected equipment, the more heat will be generated by the unit.
Do not install the Inverter/Charger near magnetic storage media, as this may result in data corruption.
Do not install the Inverter/Charger near ammable materials, fuel or chemicals.
Battery Connection Warnings
Multiple battery systems must be comprised of batteries of identical voltage, age, amp-hour capacity and type.
Because explosive hydrogen gas can accumulate near batteries if they are not well ventilated, do not install batteries in a
“dead air” compartment. The battery compartment should have some ventilation to outside air.
Sparks may result during nal battery connection. Always observe proper polarity as batteries are connected.
Do not allow objects to contact the DC input terminals. Do not short or bridge these terminals together. Serious personal
injury or property damage could result.
Ground Connection Warnings
Safe operation requires connecting the Inverter/Charger’s Main Ground Terminal directly to the frame of the vehicle or
earth ground.
Equipment Connection Warnings
Use of this equipment in life support applications where failure of this equipment can reasonably be expected to cause
the failure of the life support equipment or to signicantly affect its safety or effectiveness is not recommended. Do not
use this equipment in the presence of a ammable anesthetic mixture with air, oxygen or nitrous oxide.
You may experience uneven performance results if you connect a surge suppressor, line conditioner or UPS system to the
output of the Inverter/Charger.
User must supply proper protection for wire openings in unit panels.
Operation Warnings
Your Inverter does not require routine maintenance.
Potentially lethal voltages exist within the Inverter/Charger as long as the battery supply is connected. During any service
work, the battery supply should therefore be disconnected.
Do not connect or disconnect batteries while the Inverter/Charger is operating from the battery supply. Dangerous arcing
may result.
201110117 93-3054.indb 2 11/9/2011 10:57:55 AM
321 4 5 6 7 8 9
10 11
3
1. Overview and Features
1.1 Overview
Tripp Lite’s Sine Wave Inverter-Charger is a heavy-duty unit generating a pure sine wave from a 12V battery bank. It can
supply power to a wide range of connected equipment, from heaters, air conditioners, refrigerators and vacuum cleaners to
computers and peripheral devices. It is designed to work in heavy load conditions, so de-rating is unnecessary.
The smart charger is compatible with various battery types and sizes. The switch module automatically diverts the energy
transfer path between the inverter and an AC input. When the AC source is lower than the transfer level, the path switches
to the inverter. Otherwise, the load is powered by the AC input.
1.2 Indicators, Controls and Settings
1.2.1 Controls and LED Indicators
Shown below are the control panel and indicator lights on the front panel of the Inverter/Charger.
1 Power ON/OFF Button
2 LED 1 – DC Mode Inverter
3 LED 2 – AC Mode Charger
4 LED 3 – Inverter Condition
5 LED 4 – Battery Limits
6 LED 5 – 25% Battery Voltage
7 LED 6 – 50% Battery Voltage
8 LED 7 – 75% Battery Voltage
9 LED 8 – 100% Battery Voltage
10
Battery Temperature Port (RJ11)
11
Communication Port (RJ45)
201110117 93-3054.indb 3 11/9/2011 10:57:55 AM


Produktspezifikationen

Marke: Tripp Lite
Kategorie: Nicht kategorisiert
Modell: APSX2012SW

Brauchst du Hilfe?

Wenn Sie Hilfe mit Tripp Lite APSX2012SW benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten




Bedienungsanleitung Nicht kategorisiert Tripp Lite

Bedienungsanleitung Nicht kategorisiert

Neueste Bedienungsanleitung für -Kategorien-