Traxxas VXL-3s Bedienungsanleitung

Traxxas Funkgesteuertes Spielzeug VXL-3s

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Traxxas VXL-3s (4 Seiten) in der Kategorie Funkgesteuertes Spielzeug. Dieser Bedienungsanleitung war für 5 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Download PDF

Seite 1/4

Thank you for purchasing the Traxxas VXL-3s

™

electronic speed control. The Velineon™ VXL-3s

forward/reverse electronic speed control simplifies

brushless technology with easy, built-in profiles

and intuitive programming. The VXL-3s uses

advanced circuit design that allows sensorless

brushless motors to operate with the smoothness

and precision of the best brushless systems. The VXL-3s comes with the

peace-of-mind of the Traxxas Lifetime Electronics Warranty and unmatched

Traxxas customer support. The VXL-3s is not a toy. It is a sophisticated

electronic device capable of delivering large amounts of current. Children

under 14 years of age require adult supervision for use of the VXL-3s. If you

have questions or need assistance call us at 1-888-TRAXXAS*.

Important Precautions

VXL-3s Speed Control

• Water and Electronics Do Not Mix: Your VXL-3s brushless power system

is waterproof for use in mud, snow, puddles and other wet conditions.

Make certain the other components of your model are waterproof or have

sufficient water resistance before driving in wet conditions.

• Disconnect the Batteries: Always disconnect the battery pack from the

speed control when not in use.

• Transmitter on First: Switch on your transmitter first before switching on

the speed control to prevent runaways and erratic performance.

• Don’t Get Burned: The heat sink can get extremely hot, so be careful not

to touch it until it is cool. Supply adequate airflow for cooling.

• Use Stock Connectors: If you decide to change the battery or motor

connectors, only change one battery or motor connector at a time. This

will prevent damage from accidentally mis-wiring the speed control.

Please note that modified speed controls can be subject to a rewiring fee

when returned for service. Removing the battery connector on the speed

control or using the same-gender connectors on the speed control will

void the product’s warranty.

• Insulate the Wires: Always insulate exposed or damaged wiring with heat

shrink tubing to prevent short circuits

Batteries and Battery Charging

The Velineon Power System

uses rechargeable batteries that must be

handled with care for safety and long battery life. Make sure to read and

follow all instructions and precautions that were provided with your battery

packs and your charger. It is your responsibility to charge and care for your

battery backs properly. In addition to your battery and charger instructions,

here are some more tips to keep in mind.

• Never leave batteries to charge unattended.

• Remove the batteries from the model while charging.

• Allow the battery packs to cool off between runs (before charging).

• Always unplug the battery from the electronic speed control when the

model is not in use and when it is being stored or transported.

• Do not use battery packs that have been damaged in any way.

• Do not use battery packs that have damaged wiring, exposed wiring, or a

damaged connector.

• Children should have responsible adult supervision when charging and

handling batteries.

LiPo Batteries

Lithium Polymer (LiPo) batteries are becoming popular for use in R/C

models due to their compact size, high energy density, and high-current

output. However, these types of batteries require special care and handling

procedures for long life and safe operation. LiPo batteries are WARNING:

intended only for advanced users that are educated on the risks associated

with LiPo battery use. Traxxas does not recommend that anyone under

the age of 14 use or handle LiPo battery packs without the supervision of

a knowledgeable and responsible adult.

The VXL-3s electronic speed control is able to use LiPo batteries with

nominal voltage not to exceed 11.1 volts (3S packs) volts. LiPo batteries

have a minimum safe discharge voltage threshold that should not be

exceeded. The Velineon VXL-3s electronic speed control is equipped with

built-in Low-Voltage Detection that alerts the driver when LiPo batteries

have reached their minimum voltage (discharge) threshold. It is the driver’s

responsibility to stop immediately to prevent the battery pack from

being discharged below its safe minimum threshold.

Low-Voltage Detection on the speed control is just one part of a

comprehensive plan for safe LiPo battery use. It is critical for you, the user,

to follow all other instructions supplied by the battery manufacturer

and the charger manufacturer for proper charging, use, and storage of

LiPo batteries. Make sure you understand how to use your LiPo batteries.

Be aware that Traxxas shall not be liable for any special, indirect, incidental,

or consequential damages arising out of the installation and/or use of LiPo

batteries in Traxxas products.

If you have questions about LiPo battery usage, please consult with your

local hobby dealer or contact the battery manufacturer.

Installation

The VXL-3s will install directly into most Traxxas models in the location of

the original speed control. Rustler, Bandit, and Stampede models require the

use of the VXL-3s mounting plate (part #3725, sold separately). The VXL-3s

can also be installed in the chassis with double-sided servo tape (part #1589,

sold separately). When mounting the speed control with double-sided servo

tape, clean both application surfaces thoroughly with alcohol. The surfaces

must be perfectly clean for maximum adhesion.

Here are some tips for choosing a location for the speed control:

• The VXL-3s does not use a conventional on/off switch. Pressing the

EZ-Set button on the speed control turns it on and off. It is not necessary

to install an on/off switch into the wiring harness.

• If you are planning to operate the speed control at the higher limits of

its capabilities, cut ventilation holes into the body for the heat sinks.

Monitoring temperatures will extend the lives of

the batteries and motor and proper ventilation and

cooling will prevent premature thermal shutdown.

The VXL-3s is equipped with an additional connector

to supply power to an optional heat sink cooling fan.

An optional heat sink cooling fan can assist in cooling

the VXL-3s in high current motor applications.

• Mount the speed control so that none of the power components (wiring,

motor, ESC) contacts any part of the radio system, particularly the

antenna wire. The receiver should be mounted so the antenna wire can

be extended as far away from the speed control as possible. The antenna

wire should be extended vertically in the mast and not wrapped on the

chassis under the body. Excess antenna wire should not be coiled on

the chassis. Servo cables and the antenna wire should not cross or come

in contact with any of the motor or battery wires. These steps will help

reduce the possibility of radio interference.

• Mount the speed control where it will be protected from crash damage.

Also protect the speed control from dirt and debris kicked up by the tires.

• Mount the speed control where you will have easy access to the plugs and

the on/off (EZ-Set) button without having to remove the body.

VXL-3s Electronic Speed Control Instructions

Covers Part #3355R

Specifications:

Input voltage 4.8 - 11.1V (4 - 8 cells NiMH or 2S - 3S LiPo) ......................................................

Supported motors Sensorless brushless ..........................................................................................

Battery connector Traxxas High-Current Connector ..................................................................

Motor connectors TRX 3.5mm bullet connectors ........................................................................

Motor/battery wiring 12-gauge Maxx® Cable ...............................................................................

Thermal protection 2-stage thermal shutdown ...........................................................................

Case size (l/w/h) 55mm (2.19)/ 39mm (1.54)/ 33mm (1.3) ........................................................

Weight .................................................................................................................................. 90g (3.17oz)

Profile Selection:

Prole #1 (Sport Mode): 100% Forward, 100% Brakes, 100% Reverse

Prole #2 (Race Mode): 100% Forward, 100% Brakes, No Reverse

Prole #3 (Training Mode): 50% Forward, 100% Brakes, 50% Reverse

T R A X X A S . c o m

Traxxas, 6250 Traxxas Way, McKinney, TX 75070,

Phone: 972-549-3000, Fax: 972-549-3011, e-mail: support@Traxxas.com KC2014-R02 160217

*U.S. Customers Only

• Graphite or metal chassis have been known to transmit radio noise

generated by the motor. If the receiver is to be mounted on the chassis,

position it so the crystal (if equipped) and antenna are as far away from

the chassis as possible. This may require you to mount the receiver on its

side. This will reduce the chance of picking up radio interference from the

motor.

VXL-3s Wiring

The VXL-3s electronic speed control is capable of controlling sensorless

brushless motors. The VXL-3s auto-detects the motor type and has

numerous built-in safeguards to prevent damage from miswiring or

damaged wiring.

Sensorless brushless motors

Sensorless motors are the easiest and most reliable brushless motor type.

The VXL-3s is optimized to deliver the smoothest possible sensorless motor

performance. The Velineon 3500 is a sensorless brushless motor. The wiring

(phase alignment) of the motor determines its direction of rotation. Refer to

the wiring diagram below.

Transmitter Setup

Traxxas TQ Radio Systems

Before attempting to program your VXL-3s, it is important to make sure

your TQ transmitter is properly adjusted (set back to the factory defaults).

Otherwise, you may not get the best performance from your speed control.

The transmitter should be adjusted as follows:

1. Set the throttle neutral switch to the 50/50 setting. This adjusts the

transmitter’s throttle trigger throw to 50% for throttle and 50% for

braking and reverse. Experienced users may wish to use the 70/30

setting if more broad proportional control is desired in forward than with

braking and reverse. This might be desirable in a racing environment

where reverse is disabled.

2. Set the throttle trim control to the middle 0 setting.

3. Set the Channel 2 servo reversing switch to the left position. Do

not change the position of any of the servo reversing switches after

programming the VXL-3s.

4. You are now ready to program your speed control.

Aftermarket (Non-Traxxas) Transmitters

The following instructions are provided as a general reference only for

those who are using non-Traxxas transmitters. Consult your transmitter’s

instructions for information on how to change the settings.

1. Set the High ATV (adjustable travel volume) or EPA (end point

adjustment) to the maximum setting. This is the amount of servo throw

at full throttle.

2. Set the Low ATV, EPA or ATL (low side only trim adjustment) to the

maximum setting. This is the amount of servo throw at full brakes

or reverse.

3. Set the throttle trim to the middle (neutral setting).

4. Set the throttle channel reversing switch to either position. Do not

change the switch position after programming.

5. Set the trigger throw adjustment to 50% throttle and 50% brake (either

mechanical or electronic).

6. Set the exponential setting (if equipped) to the zero or fully linear setting.

Aftermarket Receivers

The VXL-3s is compatible with most aftermarket

receivers. By removing the tab on the edge of the power

connector, the VXL-3s can be plugged directly into some

models of Futaba®, Airtronics®, Hitec®, and JR® receivers.

Please refer to the manufacturer’s wiring diagrams that

came with your receiver. On the VXL-3s, the red wire

is positive, the black wire is negative, and the white wire is the control

wire. Warning: On some older Airtronics® radio systems, the positive and

negative terminals are opposite of the VXL-3s and an adapter is required.

Crossing the red (+) and black (-) wires could damage the receiver and the

VXL-3s. Study the manufacturer’s wiring diagrams closely, or consult your

hobby dealer.

Low-Voltage Detection Setting

The Velineon VXL-3s electronic speed control is equipped with built-in

Low-Voltage Detection. The Low Voltage Detection circuitry constantly

monitors the battery voltage. When the battery voltage begins to reach

the minimum recommended discharge voltage threshold for LiPo battery

packs, the VXL-3s will limit the power output to 50% throttle. When the

battery voltage attempts to fall below the minimum threshold, the VXL-3s

will shut down all motor output. The LED on the speed control will slowly

blink red, indicating a low voltage shutdown. The VXL-3s will stay in this

mode until a fully charged battery is connected.

The electronic speed control is factory set with Low-Voltage Detection activated.

Low-Voltage Detection should be disabled when using NiMH batteries. Never

use LiPo batteries while Low-Voltage Detection is disabled.

Verify that Low-Voltage Detection is activated:

1. Turn on the transmitter (with the throttle at neutral).

2. Connect a fully charged battery pack to the VXL-3s.

Press and release the EZ-Set button to turn the VXL-3s on. If the LED is solid

green, then Low-Voltage Detection is ACTIVATED). If the LED is solid red, then

the Low-Voltage Detection is DISABLED (not safe to use LiPo batteries).

To disable Low-Voltage Detection (NiMH setting):

Make sure the LED on the VXL-3s is on and green.

Press and hold the EZ-Set button for ten seconds.

The LED will turn o and then light red. Also, a falling

musical tone will be emitted from the motor.

3. Low-Voltage Detection is now DISABLED.

To activate Low-Voltage Detection (LiPo setting):

1. Make sure the LED on the VXL-3s is on and red.

2. Press and hold the EZ-Set button for ten seconds. The

LED will turn o and then light green. Also, a rising

musical tone will be emitted from the motor.

3. Low-Voltage Detection is now ACTIVATED.

VXL-3s Setup Programming

(Calibrating your ESC and transmitter)

Read through all of the programming steps before you begin. If you get

lost during programming or receive unexpected results, simply unplug the

battery, wait a few seconds, plug the battery back in, and start over.

1. Connect a fully charged battery pack to the VXL-3s.

2. Turn on the transmitter (with the throttle at neutral).

3. Press and hold the EZ-Set button (A). The LED will rst turn

green and then red. Release the EZ-Set button.

4. When the LED blinks RED ONCE. Pull the

throttle trigger to the full throttle position and

hold it there (B).

5. When the LED blinks RED TWICE. Push the throttle

trigger to the full reverse and hold it there (C).

6. When the LED blinks GREEN ONCE, programming

is complete. The LED will then shine green or red

(depending on low-voltage detection setting)

indicating the VXL-3s is on and at neutral.

VXL-3s Operation

To operate the speed control and test programming, place the vehicle on

a stable block or stand so that all of the driven wheels are off the ground.

Disconnect motor wires A and C, this will assure the motor does not drive

the wheels during testing. Do not test programming without disconnecting

the motor wires.

Note that in steps 1-7 below, Low Voltage Detection is

ACTIVATED (factory default) and the LED shines green. If Low Voltage Detection

is DISABLED, the LED will shine red instead of green in the following steps.

1. With the transmitter on, press and release the EZ-Set button. The LED will

shine green. This turns the VXL-3s on.

2. Apply forward throttle. The LED will turn o until full throttle power is

reached. At full throttle, the LED will illuminate green.

3. Move the trigger forward to apply the brakes. Note that braking control is

fully proportional. The LED will turn o until full braking power is reached.

At full brakes, the LED will illuminate green.

4. Return the throttle trigger to neutral. The LED will shine green.

5. Move the throttle trigger forward again to engage reverse (Prole #1). The LED

will turn o. Once full reverse power is reached, the LED will illuminate green.

6. Return the throttle trigger to neutral. (Note: There is programmed delay when

changing from reverse to forward. This prevents damage to the transmission

on high-traction surfaces.)

7. To turn the VXL-3s o, press the EZ-Set button until the LED turns

o (.5 seconds).

Green then Red

Once Red

Twice Red

VXL-3s Profile Selection

The speed control is factory set to Profile #1 (100% forward, brakes, and

reverse). To disable reverse (Profile #2) or to allow 50% forward and 50%

reverse (Profile #3), follow the steps below. The speed control should be

connected to the receiver and battery, and the transmitter should be

adjusted as described previously. The profiles are selected by entering the

programming mode.

Prole Description

Prole #1 (Sport Mode): 100% Forward, 100% Brakes, 100% Reverse

Prole #2 (Race Mode): 100% Forward, 100% Brakes, No Reverse

Prole #3 (Training Mode*): 50% Forward, 100% Brakes, 50% Reverse

Selecting Sport Mode (Prole #1: 100% Forward, 100% Brakes, 100% Reverse)

1. Connect a fully charged battery pack to the VXL-3s and turn on your

transmitter.

2. With the VXL-3s o, press and hold the EZ-Set button until the LED turns solid

green, then solid red and then begins blinking red (indicating the Prole

numbers).

3. When the LED blinks red once, release the EZ-Set button.

4. The LED will blink and then turn solid green (Low-Voltage Detection ACTIVE)

or red (Low-Voltage Detection DISABLED). The model is ready to drive.

Selecting Race Mode (Prole #2: 100% Forward, 100% Brakes, No Reverse)

1. Connect a fully charged battery pack to the VXL-3s and turn on your

transmitter.

2. With the VXL-3s o, press and hold the EZ-Set button until the LED turns solid

green, then solid red and then begins blinking red (indicating the Prole

numbers).

3. When the LED blinks red twice, release the EZ-Set button.

4. The LED will blink and then turn solid green (Low-Voltage Detection ACTIVE)

or red (Low-Voltage Detection DISABLED). The model is ready to drive.

Selecting Training Mode (Prole #3: 50% Forward, 100% Brakes, 50% Reverse)

1. Connect a fully charged battery pack to the VXL-3s and turn on your

transmitter.

2. With the VXL-3s o, press and hold the EZ-Set button until the LED turns solid

green, then solid red and then begins blinking red (indicating the Prole

numbers).

3. When the LED blinks red three times, release the EZ-Set button.

4. The LED will blink and then turn solid green (Low-Voltage Detection ACTIVE)

or red (Low-Voltage Detection DISABLED). The model is ready to drive.

Note: If you missed the mode you wanted, keep the EZ-Set button pressed

down and the blink cycle will repeat until the button is released and a Mode

is selected.

LED Codes and Protection Modes

• Solid Green: VXL-3s power on light. Low-Voltage Detection is

ACTIVATED (LiPo setting).

• Solid Red: VXL-3s power on light. Low-Voltage Detection is

DISABLED (NiCad/NiMH setting).

• Very Fast Blinking Red: Thermal Shutdown Protection and Low

Voltage Protection have occurred at the same time.

• Fast Blinking Red: Thermal Shutdown Protection, Stage 1. If the

motor has lower than normal power and the VXL-3s is hot, the VXL-

3s has entered Thermal Shutdown Protection, Stage 1, to guard

against overheating caused by excessive current flow. If the motor

has no power and the VXL-3s is very hot, the VXL-3s has entered

Thermal Shutdown Protection, Stage 2, and has automatically shut

down. Let the VXL-3s cool. Make sure your model is properly geared

for the conditions.

• Slow Blinking Red (with Low-Voltage Detection on): The VXL-3s

has entered Low-Voltage Protection. When the battery voltage

begins to reach the minimum recommended discharge voltage

threshold for LiPo battery packs, the VXL-3s will limit the power

output to 50% throttle. When the battery voltage attempts to fall

below the minimum threshold, the VXL-3s will shut down all motor

output. The LED on the speed control will slowly blink red, indicating

a low voltage shutdown. The VXL-3s will stay in this mode until a

fully charged battery is connected.

• Alternating, Blinks Red then Green: If the motor has no power,

the VXL-3s has entered Over Voltage Protection. If a battery with

too high voltage is used, the VXL-3s will go into a failsafe mode.

WARNING: If input voltage exceeds approximately 20-volts, the ESC

may be damaged. Do not exceed 12.6 maximum peak input voltage.

• Blinking Green: The VXL-3s is indicating the transmitter Throttle

Trim is incorrectly set. Adjust the Throttle Trim to the middle 0

setting.

*patented

Produktspezifikationen

Marke:	Traxxas
Kategorie:	Funkgesteuertes Spielzeug
Modell:	VXL-3s

Brauchst du Hilfe?

Wenn Sie Hilfe mit Traxxas VXL-3s benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten

Ihren Namen*

Deine E-Mail*

Schreiben Sie hier Ihre Frage

Bedienungsanleitung Funkgesteuertes Spielzeug Traxxas

Traxxas Stampede Bedienungsanleitung

29 September 2024

Traxxas 2075X Bedienungsanleitung

26 August 2024

Traxxas Mercedes-Benz G 63 AMG Bedienungsanleitung

25 August 2024

Traxxas 1/16 E-Revo VXL Bedienungsanleitung

21 August 2024

Traxxas DCB M41 Widebody Bedienungsanleitung

17 August 2024

Traxxas 2942X Bedienungsanleitung

15 August 2024

Traxxas 2950X Bedienungsanleitung

12 August 2024

Traxxas X-Maxx Bedienungsanleitung

10 August 2024

Traxxas Bigfoot Bedienungsanleitung

6 August 2024

Traxxas Slash VXL Bedienungsanleitung

2 August 2024

Bedienungsanleitung Funkgesteuertes Spielzeug

Neueste Bedienungsanleitung für -Kategorien-

Proline Trencher Bedienungsanleitung

4 Oktober 2024

Futaba 12Z Bedienungsanleitung

4 Oktober 2024

Graupner 33718.XT60 Bedienungsanleitung

3 Oktober 2024

Amewi Hyper Go Bedienungsanleitung

1 Oktober 2024

Carson Drift Burner Bedienungsanleitung

1 Oktober 2024

Carson Micro X-Warrior 2.0 Bedienungsanleitung

1 Oktober 2024

Biltema 45-8119 Bedienungsanleitung

1 Oktober 2024

Hobbywing XeRun XR10 Pro WP Bedienungsanleitung

25 September 2024

Hobbywing XeRun XR10 Stock Spec G2 Bedienungsanleitung

25 September 2024

Hobbywing XeRun XR10 Justock G3S Bedienungsanleitung

25 September 2024