TP-Link PSM150-AC Bedienungsanleitung

TP-Link Nicht kategorisiert PSM150-AC

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für TP-Link PSM150-AC (3 Seiten) in der Kategorie Nicht kategorisiert. Dieser Bedienungsanleitung war für 10 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Download PDF

Seite 1/3

Overview

The PSM150-AC is an AC-input and DC-output power supply module. It can

convert the input voltage to 12 V with the maximum output power of 150 W.

PSM150-AC

Fastening Screw AC Power Input JackPower Supply Module Handle

The PSM150-DC is a DC-input and DC-output power supply module. It can

convert the input voltage to 12 V with the maximum output power of 150 W.

PSM150-DC

Fastening Screw DC Power Input JackPower Supply Module Handle

LED and Feature Explanation

When the power module reverts to the protected state, its recovery features

are as follows.

Note:

1. The failure of output over-voltage or over-current may cause the power LED

to ash.

2. Hot-swap control function will be checked when the module is powered on

but has not been inserted into the device. If the Fault LED is on under this

condition, please do not insert the module into the device, otherwise the power

supply module or the powered devices may be damaged.

3. There is still power supply when a fan fault occurs, do not touch the module.

LED Status Description

Power On Power supply module is powered on and running well, but

not supplying power to the device.

Power On

PS OK On Power supply module is powered on and running well, and

supplying power to the device.

Power On

Fault On

The circuit has faults, such as output over-voltage

1, output

under-voltage, output over-current

1, output short circuit,

hot-swap control failure2 or fan fault3.

Power o or power supply fault.

Feature Description

Protection Function

Redundant Backup

Hot Swappable

Protection

Function Protective Action Recovery Characteristics

Note: When the power supply module is locked or auto-retry continually, you

can try the following steps to restore the device.

1. Disconnect the power cord from the external power supply system.

2. Disconnect the power cord from the power supply module.

3. Remove the power supply module from the device.

4. Insert the power supply module again.

5. Connect the power cord to the power supply module again.

6. Connect the other end of the power cord to the external supply system.

3Specication

PSM150-AC PSM150-DC

Power

Input

100 V–240 V~ 50/60 Hz

2.5A

-48 – -60 V 6 A

Output

Voltage 12 VDC 12 VDC

Output

Current 12.5 A (Maximum) 12.5 A (Maximum)

Output

Power 150 W (Maximum) 150 W (Maximum)

Temperature

Operation : 0°C to 50°C (32 to 122°F)

Storage: -40°C to 70°C (-40 to 158°F)

Humidity

Operation : 10% to 90% RH Non-condensing

Storage: 5% to 90% RH Non-condensing

Sea level to 4000 m

Supports dual power modules combining in parallel

to implement 1+1 redundancy for uninterruptible

power supply.

Includes protection of output over-voltage, output

under-voltage, output short circuit and output

over-current.

In the case of 1+1 redundant power supply system,

the power supply module can be plugged out or

plugged in without shutting down the OLT.

Output

over-voltage &

under-voltage

protection

Power supply

module locked and

cut-o supply

The power supply module can not

recover automatically.

Output short

circuit

protection

Power supply

module locked and

cut-o supply

Power supply module reverts into

the auto-retry mode. It can recover

automatically when the fault is

cleared.

Output

over-current

protection

Power supply

module locked and

cut-o supply

Power supply module reverts into

the auto-retry mode. It can recover

automatically when the fault is

cleared.

Mains

Transient

Voltage

/2500 Vpeak (Maximum)1

Installation

Install the Power Supply Module

Tools for Installation

• Straight screwdriver • Philips screwdriver • ESD-preventive wrist strap

Safety Information

To avoid damage to the power supply module and the equipment and bodily

injury, the product can only be used by instructed persons.

Please observe the following notes:

• When you install and remove the power supply module, please wear an

ESD-preventive wrist strap, and make sure that it has good skin contact and is

well grounded.

• Before installing the power supply module, make sure that the voltage of

external power supply system is the same with the voltage marked in the power

supply module, and the output voltage of the power supply module is the same

with the required voltage of the powered devices in order to prevent damaging

the power supply module or the powered devices.

• Do not touch any exposed wires or terminals to avoid bodily injury.

• Do not place the power module in a humid place or let the liquid into the

power supply module.

• If there is a failure inside the module, please contact service personnel,

instead of opening the housing of the module.

• For PSM150-DC, the rating of the external overcurrent protective device shall

not exceed 16 A.

• For PSM150-DC, an all-pole mains switch in accordance with EN 62368-1

2014 Annex L shall be incorporated in the electrical installation of the building.

And the disconnect device shall have a contact separation of at least 1.5 mm.

• The equipment must not be used in locations where children are likely to be

present.

For simplicity, we will take PSM150-AC for example.

Note:

1.The product can be powered by a DC power source such as accumulator cell

and a power supply server. The DC power supply should comply with EN

62368-1 2014 clause 5.4.2.3.2.3, and the transient voltage shall be no more

than 2500 Vpeak

1. Wear an ESD-preventive wrist strap, and make sure that it has good skin

contact and is well grounded.

2. Grip the handle of the module with one hand, and hold the bottom of the

module using your other hand. Gently push the module in along the slot guide

rail.

3. Tighten the captive screws with a Phillips screwdriver to x the power supply

module in place.

PSM150-AC:

Connect the Power Cord and Connect to the Ground

After the power supply module is installed on the device, please plug the

female connector of the provided power cord into the power socket of the

device, and the male connector into a power outlet. Meanwhile, it will connect

to the ground via the power supply.

Altitude

Installation Guide

Power Supply Module

Remove the Power Supply Module

1. Wear an ESD-preventive wrist strap, and make sure that it has good skin

contact and is well grounded.

2. Remove the power cord from the external power supply system and the

power module.

3. Use a Phillips screwdriver to loosen the captive screws at both sides of the

power supply module until all spring pressure is released.

4. Pull the handle with one hand along the guide rails, and hold the bottom of

the module using your other hand, until it completely comes out of the chassis.

Note:

When installing or removing a power supply module, pay attention to the

following points:

• Make sure that the power supply module is set correctly in the operation of

installation.

• Do not use too much force in the installation. If resistance is encountered or

positions of the power supply module appear larger during installation, you

must rst remove the module and then reinstall the module.

• If screws cannot be tightened, it may be due to the power supply module is

not installed properly. Please check carefully.

• In order to better protect the power supply module during removal, it is

recommended that you package it in an antistatic bag.

Safety Information

Keep the device away from water, re, humidity or hot environments.

Do not attempt to disassemble, repair, or modify the device. If you

need service, please contact us.

Avoid using this product during an electrical storm. There may be a

remote risk of electric shock from lightning.

EU Declaration of Conformity

TP-Link hereby declares that the device is in compliance with the

essential requirements and other relevant provisions of directives

2014/30/EU, 2014/35/EU, 2009/125/EC, 2011/65/EU and (EU)2015/863.

The original EU declaration of conformity may be found at

https://www.tp-link.com/en/support/ce/

UK Declaration of Conformity

TP-Link hereby declares that the device is in compliance with the

essential requirements and other relevant provisions of the

Electromagnetic Compatibility Regulations 2016 and Electrical

Equipment (Safety) Regulations 2016.

The original UK Declaration of Conformity may be found at

https://www.tp-link.com/support/ukca

PSM150-DC:

Connect the Power Cord and Connect to the Ground

For technical support, the user guide and other information,

please visit https://www.tp-link.com/support, or simply

scan the QR code.

If you have any suggestions or needs on the product

guides, welcome to email techwriter@tp-link.com.cn.

To ask questions, find answers, and communicate with TP-Link users

or engineers, please visit https://community.tp-link.com to join

TP-Link Community.

• Equipotential bonding

Equipotential bonding is the practice of intentionally electrically connecting all

earthed systems to the same grounding grid or connecting the grounding

grids of all the earthed systems together through the ground or overground

metal so as to create an earthed equipotential zone. When lightning occurs, the

high voltage produced by lightning current in all systems will meanwhile exist in

their ground cables, and thus all ground cables have the same electrical

potential and basically eliminate the electric strikes between the systems. The

gure below illustrates how to practice equipotential bonding in a network.

Grounding Terminal Equipotential Bonding Cable

Grounding Bar Ground Cable (18-14 AWG)

• Use the grounding bar

If the device is installed in the Equipment Room, where a grounding bar is

available, it is recommended to connect the device to the grounding bar with

an 18-14 AWG ground cable as shown in the following gure.

Device (Rear Panel)

Ground Cable (18-14 AWG)

Grounding Terminal

Grounding Bar

1. Connect the power cord

It is recommended to use an 18-14 AWG power cord to connect the power

supply equipment and PSM150-DC, and make sure that the connection is

reliable. When connecting, make sure that the positive and negative poles of

the power supply equipment correspond to the positive and negative poles of

the PSM150-DC.

2. Connect to the ground

In dierent environments, the device may be grounded dierently. The

following will instruct you to connect the device to the ground in two ways.

Note that the protective earthing terminal must be connected to the installation

protective earthing conductor.

CAN ICES-3 (A)/NMB-3(A)

Industry Canada Statement

この装置は、クラスA情報技術装置です。この装置を家庭環境で使

用すると電波妨害を引き起こすことがあります。この場合には使用

者が適切な対策を講ずるよう要求されることがあります。

VCCI-A

This is a class A product. In a domestic environment, this product may cause

radio interference, in which case the user may be required to take adequate

measures.

CE Mark Warning

FCC compliance information statement

This equipment has been tested and found to comply with the limits for a Class

A digital device, pursuant to part 15 of the FCC Rules. These limits are

designed to provide reasonable protection against harmful interference when

the equipment is operated in a commercial environment. This equipment

generates, uses, and can radiate radio frequency energy and, if not installed

and used in accordance with the instruction manual, may cause harmful

interference to radio communications. Operation of this equipment in a

residential area is likely to cause harmful interference in which case the user will

be required to correct the interference at his own expense.

This device complies with part 15 of the FCC Rules. Operation is subject to the

following two conditions:

1) This device may not cause harmful interference.

2) This device must accept any interference received, including interference

that may cause undesired operation.

Any changes or modications not expressly approved by the party responsible

for compliance could void the user’s authority to operate the equipment.

Product Name: Power Supply Module

Model Number: PSM150-AC/PSM150-DC

Responsible party:

TP-Link USA Corporation, d/b/a TP-Link North America, Inc.

Address: 10 Mauchly, Irvine, CA 92618

Website: https://www.tp-link.com/us/

Tel: +1 626 333 0234

Fax: +1 909 527 6803

E-mail: sales.usa@tp-link.com

We, TP-Link USA Corporation, has determined that the equipment shown as

above has been shown to comply with the applicable technical standards, FCC

part 15. There is no unauthorized change is made in the equipment and the

equipment is properly maintained and operated.

Issue Date: 2021/07/01

BSMI Notice

安全諮詢及注意事項

請使用原裝電源供應器或只能按照本產品注明的電源類型使用

本產品。

清潔本產品之前請先拔掉電源線。請勿使用液體、噴霧清潔劑或

濕布進行清潔。

注意防潮，請勿將水或其他液體潑灑到本產品上。

插槽與開口供通風使用，以確保本產品的操作可靠並防止過熱，

請勿堵塞或覆蓋開口。

請勿將本產品置放於靠近熱源的地方。除非有正常的通風，否則

不可放在密閉位置中。

請不要私自拆開機殼或自行維修，如產品有故障請與原廠或代理

商聯繫。

此為甲類資訊技術設備，于居住環境中使用時，可能會造成射頻擾動

，在此種情況下，使用者會被要求採取某些適當的對策。

限用物質含有情況標示聲明書

產品元件名稱

PCB

外殼

產品元件名稱

PCB

外殼

限用物質及其化學符號

備考： "○"系指該項限用物質之百分比含量未超出百分比含量基準值。

鉛

○

鎘

○

汞

○

六價鉻

Cr+6

○

多溴聯苯

PBB

○

多

溴二苯醚

PBDE

○

Explanation of the symbols on the product label

DC voltage

RECYCLING

This product bears the selective sorting symbol

for Waste electrical and electronic equipment

(WEEE). This means that this product must be

handled pursuant to European directive

2012/19/EU in order to be recycled or

dismantled to minimize its impact on the

environment.

User has the choice to give his product to a

competent recycling organization or to the

retailer when he buys a new electrical or

electronic equipment.

AC voltage

Indoor use only

Operator’s manual

Caution

Produktspezifikationen

Marke:	TP-Link
Kategorie:	Nicht kategorisiert
Modell:	PSM150-AC
Breite:	241.8 mm
Tiefe:	120 mm
Produktfarbe:	Grau
Höhe:	41.6 mm
Energieschutzeigenschaften:	Over current,Over voltage,Short circuit,Under voltage
Zweck:	Netzvermittlung
Betriebstemperatur:	0 - 70 °C
Relative Luftfeuchtigkeit in Betrieb:	10 - 90 %
Verpackungsbreite:	400 mm
Verpackungstiefe:	250 mm
Verpackungshöhe:	80 mm
Paketgewicht:	1420 g
Menge pro Packung:	- Stück(e)
LED-Anzeigen:	Ja
Temperaturbereich bei Lagerung:	-40 - 80 °C
Luftfeuchtigkeit bei Lagerung:	5 - 90 %
Netzteiltyp:	Indoor
Ausgangsstrom:	12.5 A
Ausgangsspannung:	12 V
Ausgangsleistung:	150 W
Eingangsspannung:	100-240 V
Eingangsstrom:	2.5 A
Eingangsfrequenz:	50/63 Hz
Entfernbare Stromverbindungen:	Ja
Starkstromtyp:	AC-an-DC
Kompatibilität:	TP-Link