TP-Link EAP110-Outdoor V3 Bedienungsanleitung

TP-Link Zugangspunkt EAP110-Outdoor V3

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für TP-Link EAP110-Outdoor V3 (4 Seiten) in der Kategorie Zugangspunkt. Dieser Bedienungsanleitung war für 21 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Download PDF

Seite 1/4

Indoor/Outdoor Access Point

Overview

Package Contents

Panel Layout

Power LED:

On: Power on

Off: Power off

Note: EAP225-Outdoor does not support the Remote Reset feature.

Passive PoE Adapter

Remote Reset:

Press and hold for about 8 seconds until

the LED is quickly flashing yellow then

green. The EAP will restore to factory

default settings.

LED Status Indication

Solid green The device is initializing or working properly.

Flashing yellow System errors. RAM, Flash, Ethernet, WLAN or

rmware may be malfunctioning.

Flashing yellow, green Firmware update is in progress. Do not disconnect

or power o the device.

Quickly ashing yellow, green The device is being reset to its factory default

settings.

Flashes green twice Initialization is completed.

SYS LED Explanation

Flashing green slowly

(Only for EAP225-Outdoor) The device is in an isolated state.

Lightning and ESD Protection

Before mounting the EAP, you should consider Lightning and ESD

Protection to ensure safety.

Proper grounding is extremely important for outdoor devices. By using a

shielded CAT5e (or above) cable for connection, you can reduce the

damage of ESD attacks.

Hardware Installation

Mount the EAP

The EAP can be pole-mounted or wall-mounted. Follow the steps below

for the appropriate installation.

Option 1: Pole Mounting

Lead the end of the pole mounting strap

through the back of the EAP.

Step 1:

Position the EAP and wrap the pole

mounting strap around the pole. Feed the

end through the screw-block and tighten

the strap until the EAP is secure.

Step 2:

Option 2: Wall Mounting

Step 1:

Place the mounting bracket (for EAP) in

the right position. Mark two positions

for the screw holes .

Drill two 6 mm holes for the screws at

the marked positions.

Step 2:

Insert the plastic wall anchors into the 6

mm holes. Align the bracket (for EAP) to

the plastic wall anchors and drive the

self-tapping screws into the anchors

through the bracket (for EAP).

Step 3:

Align the mounting tabs on the back of

the EAP with the slot of the mounting

bracket (for EAP). Push and slide the

EAP downward until it locks into place.

3Connect Cables

Firmly grasp the rear of the interface

cover and pull it downward.

Step 1:

Use an adequate Ethernet cable to

connect the LAN port. The length of

cable is up to 100 m for steady power

supply. Shielded CAT5e (or above) cable

is recommended.

Step 2:

Step 3:

Attach the waterproof rubber insert to the

groove at the underside of the device for

waterproong. Move the Ethernet cable to

the hole of the waterproof rubber insert.

Flatten the waterproof rubber insert until

it gets parallel to the device. Replace the

cover until it rmly locks into place.

Step 4:

EAP

Grounded PoE Adapter

Shielded CAT5e (or above)

Cable

Grounded 3-wire

Power Outlet

RESETShielded Ethernet

Port LAN

Passive PoE Adapter

(Mounting Bracket Included)

Power Cord

M3×28 Plastic Wall

Anchors (Qty.4)

M3×20 Self-tapping

Screws (Qty.2)

EAP

Antennas (Qty.2)

Mounting Bracket

(for EAP)

Installation Guide

Pole Mounting StrapWaterproof Rubber

Insert

M3×16 Self-tapping

Screws (Qty.2)

Connect the antennas to the EAP. For

optimal Wi-Fi performance, adjust the

direction of the antennas. It is recom-

mended to position the antennas at

45-degree angles.

Step 3:

Step 4:

Connect the antennas to the EAP. For

optimal Wi-Fi performance, adjust the

direction of the antennas. It is recom-

mended to position the antennas at

45-degree angles.

Quick Installation Guide

Setup with videos

Visit https://www.tp-link.com/support/setup-video/ or scan the QR

code to search for the setup video of your product model.

Option 2: Via PoE Switch (Only for EAP225-Outdoor)

PoE Switch

Connect an Ethernet cable from the PoE switch to the Ethernet port.

Power On

The EAP can be powered via the provided passive PoE adapter or a PSE

device (such as a PoE switch).

Connect the EAP to a Power over Ethernet (PoE) adapter as follows:

Option 1: Via Passive PoE Adapter

Connecting the PoE Adapter

PoE LAN

Ethernet cable

length up to 100 m

Mounting the PoE Adapter (Optional)

Note: To ensure the passive PoE adapter is attached most securely, it is

recommended to install the adapter with the Ethernet port facing upward.

Step 1:

Remove the mounting bracket from the

passive PoE Adapter.

Drill two holes on the wall and insert the

plastic wall anchors into the the holes.

Secure the mounting bracket to the wall.

Make sure the shoulders at the corners

of the mounting bracket are on the

outside and pointing upward.

Step 2:

Attach the passive PoE adapter to the

mounting bracket (for PoE Adapter)

by sliding the adapter in the direction

of the arrows until it locks into place.

Attention:

For EAP225-Outdoor, in EU member states and EFTA countries, the operation in the

frequency range 5150MHz-5350MHz is only permitted indoors.

For EAP Controller, go to Access Point page and select the desired EAP to specify the

channel. For web browser, go to Wireless > Wireless Settings to specify the channel.

AT BE BG CH DE DK EE EL FI FR HR HU IECY CZ ES

IS IT LI MT NL NO SE SI SK UKLT LU LV PL PT RO

For detailed configurations, please visit https://www.tp-link.com/support to download

the User Guide of EAP in the download center.

For technical support, the user guide and other information,

please visit https://www.tp-link.com/support, or simply scan

the QR code.

If you have any suggestions or needs on the product guides,

welcome to email techwriter@tp-link.com.cn.

To ask questions, find answers, and communicate with TP-Link

users or engineers, please visit https://community.tp-link.com

to join TP-Link Community.

The products of TP-Link partly contain software code developed by third parties,

including software code subject to the GNU General Public License (“GPL”). As applicable,

the terms of the GPL and any information on obtaining access to the respective GPL

Code used in TP-Link products are available to you in GPL-Code-Centre under (https://w-

ww.tp-link.com/en/support/gpl/). The respective programs are distributed WITHOUT ANY

WARRANTY and are subject to the copyrights of one or more authors. For details, see the

GPL Code and other terms of the GPL.

Safety Information

Keep the device away from water, re, humidity or hot environments.

Do not attempt to disassemble, repair, or modify the device. If you need service,

please contact us.

Do not use the device where wireless devices are not allowed.

Do not use any other chargers than those recommended.

Adapter shall be installed near the equipment and shall be easily accessible.

Option1: Standalone Mode

Via Omada App

1. Connect wirelessly by using the default SSID (format:

TP-Link_2.4GHz/5GHz_XXXXXX) printed on the label at the bottom of the product.

2. Launch a web browser and enter http://tplinkeap.net in the address bar. Use for admin

both Username and Password to log in.

3. Set up a new Username and Password for secure management purpose. Modify the

wireless parameters and reconnect your wireless devices to the new wireless

network.

2. Connect your mobile device to the EAP by using the default SSID (format:

TP-Link_2.4GHz/5GHz_XXXXXX) printed on the label at the bottom of the product.

3. Open the Omada App, and wait for the EAP to appear on the page. Standalone APs

Tap on the EAP you want to congure.

The Omada App is designed to help you quickly configure the common settings. If you

want to configure advanced settings, log in to the web page of your EAP or the controller.

To configure other EAPs, connect your device to the EAP by the coresponding default

SSID and repeat the steps listed above. You can configure some basic functions in

Standalone Mode. If you want to configure advanced functions, use Controller Mode.

Software Conguration

Internet

Clients

Router

EAP

A DHCP server (typically a router with DHCP function enabled) is required to assign IP

addresses to the EAPs and clients in your local network.

To configure and manage EAPs singly (usually suitable for a small network with a few

EAPs), Standalone Mode is recommended. Please refer to Option 1.

To configure and manage EAPs in batch, Controller Mode is recommended. Please

refer to Option 2.

The EAP supports two configuring options:

Controller Mode is applicable to configuration for mass EAPs. All EAPs can be centrally

configured and monitored via Omada Software Controller, Omada Hardware Controller

(OC200/OC300) or Omada Cloud-Based Controller.

Switch

Router

Omada Hardware Controller Omada Software Controller

running on the Host PC

(OC200/OC300)

Omada Hardware Controller (OC200/OC300), which is pre-installed with Omada Software

Controller, is a good alternative if you have no spare PC to keep running Omada Software

Controller in the network. It needs to be purchased additionally. For more details, refer to

the Installation Guide of OC200/OC300.

Via Omada Software Controller

Via Omada Hardware Controller (OC200/OC300)

1. Download the TP-Link Omada App on your mobile device. It can be downloaded from

App Store or Google Play:

Scan for Omada App Download Omada App

With Omada App, you can also manage your Omada Software Controller at a local site and

remote site. Note that Omada Software Controller needs to be kept running when using

Omada App.

Local Management

Omada App

2. Launch your Omada App and configure the controller at local a site or remote site.

a. Connect your mobile device to the EAP by using the default SSID (format:

TP-Link_2.4GHz/5GHz_XXXXXX) printed on the label at the bottom of the

product.

b. Launch Omada App and go to Local Access, tap the button on the upper-right +

corner to add the controller. Then you can further congure the controller.

Remote Management

a. Make sure Cloud Access is enabled on your controller and your controller has

been bound with your TP-Link ID.

b. Launch Omada App and log in with your TP-Link ID. Then go to . A Cloud Access

list of controllers that have been bound with your TP-Link ID will appear. Then you

can further configure the controller.

1. On the PC with Windows OS or Linux OS, download the Omada Software Controller

installation file from

https://www.tp-link.com/support/download/omada-software-controller/.

2. Run the file and follow the wizard to install the Omada Software Controller.

3. Launch the Omada Software Controller and follow the step-by-step instructions to

complete the Quick Setup.

4. After the wizard is finished, a login screen will appear. Enter the username and

password you created and click . Then you can further configure the controller. Log in

1. Enable Cloud Access on the setting page on the controller and bind a TP-Link ID

to your controller. If you have congured this in the setup wizard, skip the step.

2. Launch a web browser and enter https://omada.tplinkcloud.com in the address bar.

3. Enter your TP-Link ID and password to log in. A list of controllers that have been

bound with your TP-Link ID will appear. Then you can click to further Launch

congure the controller.

After installing Omada Software Controller, you can remotely access and configure

the controller through Omada Cloud Service. Follow the steps below.

Via Omada Cloud-Based Controller

2. Launch Omada App and log in with your TP-Link ID. Then go to Cloud Access. A list of

controllers that have been bound with your TP-Link ID will appear. Then you can further

configure the controller.

With Omada App, you can also manage your Omada Cloud-Based Controller.

Omada App

1. Launch a web browser and enter https://omada.tplinkcloud.com in the address bar. Then

enter your TP-Link ID and password to log in.

2. Add Controller Click and subscribe to Omada Cloud-Based Controller. Follow the

instructions to choose a plan and complete the payment. Then wait until your controller

is deployed.

3. The controller will appear in the list once bound with your TP-Link ID. Click and Launch

follow the step-by-step instructions to complete the Quick Setup. After the wizard is

nished, log in via the created username and password.

4. Devices Add Devices Click on the side bar and then click . Then you can add devices to

the controller manually through the serial numbers at the bottom of the product.

Via a Web Browser

Option2: Controller Mode

EAP

1. Download the TP-Link Omada App on your mobile device. It can be downloaded from

App Store or Google Play:

EAP EAP

Clients

EAP

Controller

Switch

Router

EAP EAP

Clients

EAP

Omada Cloud-Based Controller

Scan for Omada App Download Omada App

1. Download the TP-Link Omada App on your mobile device. It can be downloaded from

App Store or Google Play:

Scan for Omada App Download Omada App

Omada Cloud Service

Produktspezifikationen

Marke:	TP-Link
Kategorie:	Zugangspunkt
Modell:	EAP110-Outdoor V3
Breite:	216 mm
Tiefe:	46 mm
Mitgelieferte Kabel:	AC
Produktfarbe:	Weiß
Internationale Schutzart (IP-Code):	IP65
Höhe:	27 mm
Platzierung:	Pole, Wall
Antennentyp:	Extern
Betriebstemperatur:	-30 - 65 °C
Relative Luftfeuchtigkeit in Betrieb:	10 - 90 %
Verpackungsbreite:	140 mm
Verpackungstiefe:	270 mm
Verpackungshöhe:	100 mm
Paketgewicht:	620 g
Netzstandard:	IEEE 802.11b, IEEE 802.11g, IEEE 802.11n
Unterstützte Sicherheitsalgorithmen:	WPA-Enterprise, WPA-PSK, WPA2-Enterprise, WPA2-PSK
Quality of Service (QoS) Support:	Ja
Zertifizierung:	CE, FCC, RoHS
Power over Ethernet (PoE):	Ja
Anzahl Ethernet-LAN-Anschlüsse (RJ-45):	1
Stromverbrauch (max.):	3.12 W
Verpackungsart:	Box
Maximale Datenübertragungsrate:	300 Mbit/s
Ethernet LAN Datentransferraten:	10, 100 Mbit/s
2,4 GHz:	Ja
Antenne Zunahmeniveau (max):	3 dBi
Anzahl der Antennen:	2
LED-Anzeigen:	Leistung
Temperaturbereich bei Lagerung:	-40 - 70 °C
Luftfeuchtigkeit bei Lagerung:	5 - 90 %
Montageset:	Ja
Frequenzband:	2.4 GHz
Anzahl enthaltener Produkte:	1 Stück(e)
Web-basiertes Management:	Ja
VLAN-Unterstützung:	Ja
Management-Protokolle:	HTTP/HTTPS, SNMP, Telnet
Kompatible Betriebssysteme:	Microsoft Windows XP, Vista, Windows 7, Windows 8, Windows10
Ausgangsstrom:	0.6 A
Ausgangsspannung:	24 V
Nachhaltigkeitskonformität:	Ja
Nachhaltigkeitszertifikate:	CE, Federal Communications Commission (FCC), RoHS
MAC Adressen Filtern:	Ja
Reset-Knopf:	Ja
5 GHz:	Nein
Kabellose Isolierung:	Ja
WLAN-Multimedia (WMM)/(WME):	Ja
Antennenfunktionen:	Abnehmbare Antenne
Anzahl der SSID-Unterstützung:	8
Fernauthentifizierungs-Einwähl-Benutzerdienst (RADIUS):	Ja
Automatische Kanalwahl:	Ja
Virtuelle LAN-Funktionen:	Tagged VLAN, VLAN mapping
Ratenbeschränkung:	Ja
Zugriffkontrollliste:	Ja
Antenne enthalten:	Ja
Sendeleistung (FCC):	22 dbm
Antennenrichtungsart:	Mit kugelförmiger Richtcharakteristik
Funktionen Service Set Identifier (SSID):	Multiple SSIDs
Maximale Datenübertragungsrate (2,4 GHz):	300 Mbit/s
Syslog:	Ja
PoE-Adapter enthalten (Power over Ethernet):	Ja
Sendeleistung (CE):	20 dbm
Power-over-Ethernet (PoE)-Typ unterstützt:	Passive PoE
6 GHz:	Nein