TOA ST-16A Bedienungsanleitung

TOA Lautsprecherunterstützung ST-16A

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für TOA ST-16A (2 Seiten) in der Kategorie Lautsprecherunterstützung. Dieser Bedienungsanleitung war für 20 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Download PDF
Seite 1/2
ST-16ASPEAKER STAND
INSTRUCTION MANUAL
1. SAFETY PRECAUTIONS
• Before installation or use, be sure to carefully read all the instructions in this section for correct and safe
operation.
• Be sure to follow all the precautionary instructions in this section, which contain important warnings and/or
cautions regarding safety.
• After reading, keep this manual handy for future reference.
2. HOW TO USE
Step 1. Attach the bracket to the speaker as shown below.
Attach the bracket to the speaker
Indicates a potentially hazardous situation which, if mishandled, could
result in death or serious personal injury.
WARNING
• Do not mount the speaker of 7 kg or more. The stand or its internal pipe may fall down or drop, resulting in
personal injury. Even though the speaker weight is below 7 kg, do not use that speaker if the stand is made
unstable.
• Do not extend the internal pipe beyond the MAXIMUM point marked in red. Doing so may make the stand
unstable, and cause the stand or its internal pipe to fall down or drop, resulting in personal injury.
• Avoid installing the stand in the following locations. Otherwise, the mounted speaker may drop or the stand
may fall, resulting in personal injury.
· Doorway or other high traffic area where people may trip on the stand.
· Locations where the unit is exposed to a strong wind.
· Unstable locations, such as on a rickety table or a slanted surface.
Important: Even in locations other than the above, if the unit may fall down, take appropriate fall preventive
measures.
• When adjusting the stand height with the speaker mounted, hold the speaker firmly. Doing otherwise may
cause the stand to fall, resulting in personal injury and/or property damage.
• Fully expand the legs. If the legs are not fully expanded, the stand may fall down, resulting in personal injury.
Attachment to the horn speaker Attachment to the FGM speakerAttachment to the megaphone
Butterfly nut
Washer
Hexagon bolt
Insert the hexagon bolt into the hexagonal
hole located inside the bracket and tighten
the bolt to attach the bracket.
Hexagon bolt
Insert the hexagon bolt into the hexagonal hole
located inside the bracket and tighten the bolt
rotating the bracket in the direction of the arrow
to secure the bracket.
Spacer
Be sure to use the spacer.
If not used, the thread in the
megaphone may be destroyed.
Note
Do not use this spacer for the
megaphones ER-2230W and
WR-2930W.
Speaker
mounting screw
Bracket
Bracket
Bracket
Step 2. Loosen the leg locking knob to fully expand the legs. Lowering the slide leg adjustment till it hits the
stopper in the center of the external pipe permits maximum leg expansion.
Step 3. Tighten the leg locking knob to secure the legs.
Step 4. Loosen the internal pipe locking knob to raise the internal pipe to the desired height.
Step 5. Tighten the internal pipe locking knob to secure the pipe.
Step 6. Insert the bracket onto the top of the internal pipe, and mount the speaker on the stand.
Step 7. After determining the orientation of the speaker, secure the speaker by tightening the bracket fixing
knob.
Note: After installation completion, ensure again that every knob is tightened.
Step 8. After use, reverse the procedures 1 – 7 above to detach the speaker and fold the stand.
Note: Be sure to fold the stand after detaching the speaker from the stand.
[Storing mounting screws]
Speaker mounting screws for installing the FGM speakers can be stored
by mounting them into the storage holes provided in the bracket.
Use these holes to prevent the loss of screws while putting away the
equipment.
Put away the stand after use
Mount the speaker on the stand
Put up the stand
1130 – 1660 mm
1050 mm
Speaker mounting screw
(M5 x 20) x 2
Hexagon bolt
(M8 x 20) x 1
Washer x 1
Spacer x 1
Butterfly nut x 1
Weight: 1.7 kg (bracket included)
Bracket
Slide leg
adjustment
External pipe
Stopper
Stay
Bracket fixing knob
Internal pipe
Internal pipe
locking knob
Leg locking knob
Bracket
Bracket fixing
knob
Internal pipe
Internal pipe
locking knob
External pipe
Leg locking
knob
Stopper
Slide leg adjustment
Leg
Stay
Speaker mounting
screw
Bracket
Screw storage hole
3. PART NAMES
Stand (when in use)Stand (when folded)Accessory

Produktspezifikationen

Marke: TOA
Kategorie: Lautsprecherunterstützung
Modell: ST-16A

Brauchst du Hilfe?

Wenn Sie Hilfe mit TOA ST-16A benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten


Bedienungsanleitung Lautsprecherunterstützung TOA

TOA

TOA ST-16A Bedienungsanleitung

20 Juli 2024

Bedienungsanleitung Lautsprecherunterstützung

Neueste Bedienungsanleitung für -Kategorien-

Pioneer

Pioneer CP-4EX Bedienungsanleitung

4 Oktober 2024
Bose

Bose FS3B-II Surface Mount Kit Bedienungsanleitung

30 September 2024
Omnitronic

Omnitronic DS-1 Bedienungsanleitung

18 September 2024
Extron

Extron V-Lock Bedienungsanleitung

6 September 2024
Extron

Extron SMK VRE 48 Bedienungsanleitung

6 September 2024
Sanus

Sanus BSWM3IWP Bedienungsanleitung

6 September 2024
Sanus

Sanus WSWM3IWP Bedienungsanleitung

6 September 2024
Valcom

Valcom V-9915M Bedienungsanleitung

6 September 2024
Valcom

Valcom V-9912M Bedienungsanleitung

6 September 2024
Valcom

Valcom V-9910 Bedienungsanleitung

6 September 2024