TOA SR-SA3 Bedienungsanleitung


Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für TOA SR-SA3 (1 Seiten) in der Kategorie Nicht kategorisiert. Dieser Bedienungsanleitung war für 10 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Seite 1/1
INSTALLATION MANUAL
STAND ADAPTER SR-SA3
The SR-SA3 is a Stand Adapter designed to install the Line Array
Speaker SR-H2L, SR-H2S, SR-H3L, or SR-H3S on the ST-33B
Speaker Stand.
2. SPECIFICATIONS
Note: The design and specifications are subject to change without
notice for improvement.
133-05-447-70
URL: http://www.toa.jp/
1. SAFETY PRECAUTIONS
3. INSTALLATION (See the figure at right.) 4. HOW TO USE
[About a height limit of the speaker]
[About a conversion cable for speaker cable]
When connecting the speaker cable to the speaker input terminal
via the XLR or Neutrick Speakon connector, use a short
conversion cable as shown below, then secure it on the speaker’s
rear with a cable clamp.
Before installation or use, be sure to carefully read all the
instructions in this section for correct and safe operation.
Be sure to follow all the precautionary instructions in this section,
which contain important warnings and/or cautions regarding
safety.
After reading, keep this manual handy for future reference.
WARNING
Indicates a potentially hazardous situation which, if
mishandled, could result in death or serious personal injury.
CAUTION
Indicates a potentially hazardous situation which, if
mishandled, could result in moderate or minor personal injury,
and/or property damage.
Applicable Speaker SR-H2L, SR-H2S, SR-H3L, SR-H3S
Applicable Stand ST-33B
Finish Rolled steel plate, black, paint
Dimensions 62 (w) x 385 (h) x 69 (d) mm
(2.44" x 15.16" x 2.72")
Weight 1.4 kg (3.09 lb)
Accessory Hex bolt M5 x 25 (with washer) ....... 4
The safety precautions in this section apply to the SR-SA3 Stand
Adapter. For precautions relating to other combination products,
refer to the instruction manual enclosed with each equipment.
Do not use other methods than specified to mount the Stand
Adapter. Extreme force is applied to the unit and the unit could fall
down or off, possibly resulting in personal injuries.
Ensure that all bolts are securely tightened. If they are not
tightened or firmly secured after installation, the unit could fall
down or off, possibly resulting in personal injury.
Use the SR-H2L, SR-H2S, SR-H3L, or SR-H3S speaker, and the
ST-33B Speaker Stand in combination. Doing otherwise may
cause the speaker system to fall down or off, resulting in personal
injury.
Be sure to follow the precautions below when using the speaker
stand. Otherwise, the stand with speaker installed may fall down,
causing personal injury.
· Spread the tripod legs until the stays extend horizontally.
· The height of the speaker's top surface from the floor must be
240 cm (95") or less.
Avoid touching the unit's sharp metal edge to prevent injury.
[SR-H2L]
SR-SA3
[SR-H2S] [SR-H3L] [SR-H3S]
Stand Adapter mounting position
Hex bolt M5 x 25
(supplied with the SR-SA3)
Note
Remove the attached screws.
The removed screws are not used.
WARNING
When using the speaker stand, the height of the
speaker's top surface from the floor must be 240 cm
(95") or less. Otherwise, the stand may fall down,
causing personal injury.
The height must be 240 cm (95") or less.
(Applicable to all applicable speakers)
Removable input connector
(supplied with the speaker)
Cable clamp
Note
When securing the cable clamp,
never use these 4 screws.
Conversion cable
Note
Prepare the conversion cable and cable clamp separately.
2
1
The figure shows an example for installing the SR-H3S.
WARNING
Spread the tripod legs until the stays extend horizontally
and always use the stand in stable condition. If the legs
are not sufficiently spread, this may cause the stand and
mounted speaker to fall down, resulting in personal injury.
Removable input connector
Speaker body
(rear)
Stand Adapter
(SR-SA3)
Hex bolt M5 x 25
(supplied with the
SR-SA3)
Knob bolt
Speaker stand
(ST-33B)
Stay
Note
Only 1 speaker can be installed using the SR-SA3. (Never use the
SR-SA3 to install the linked speakers.)
Step 1. Attach the Stand Adapter to the speaker's rear.
Remove the specified screws on the speaker's rear
surface, then use their screw holes to secure the Stand
Adapter. In this event, the removed screws are not used.
Note
For the Stand Adapter mounting position, refer to the figure
below.
Step 2. Mount the speaker (with the Adapter attached) on
the stand, then securely tighten the Adapters
knob bolt.
Notes
Spread the tripod legs wide apart enough to keep the
stand stable.
Lower the height of the speaker stand to make
installation work easier.
For the speaker stand installation, refer to the instruction
manual enclosed with the ST-33B Speaker Stand.
For the speaker cable connection, refer to the instruction
manual enclosed with the applicable speaker.


Produktspezifikationen

Marke: TOA
Kategorie: Nicht kategorisiert
Modell: SR-SA3

Brauchst du Hilfe?

Wenn Sie Hilfe mit TOA SR-SA3 benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten




Bedienungsanleitung Nicht kategorisiert TOA

Bedienungsanleitung Nicht kategorisiert

Neueste Bedienungsanleitung für -Kategorien-