Tennsco CVD1480 Bedienungsanleitung
Tennsco
Kleiderschrank
CVD1480
Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Tennsco CVD1480 (4 Seiten) in der Kategorie Kleiderschrank. Dieser Bedienungsanleitung war für 10 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet
Seite 1/4
GENERAL SAFETY INFORMATION
Some parts may have sharp edges. CARE must be taken when handling
For safety, wear a pair of work gloves when assembling or performing
LIMITED WARRANTY
Tennsco warrants goods purchased hereunder to be free of defects in materials and workmanship for a period of one (1) year from th
in the event goods are damaged as a result of misuse, abuse, neglect, accident, improper application, modication or repair by person
shipment, or where the date stamps on the goods have been defaced, modied or removed. UNLESS CONSIDERED UNENFORCEABLE
a. ALL IMPLIED WARRANTIES, INCLUDING BUT NOT LIMITED TO WARRANTIES OR MERCHANTABILITY AND FITNESS FOR A
b. BUYERS REMEDY, IF ANY, FOR ANY DEFECTIVE GOODS SHALL BE LIMITED TO A REFUND BY SELLER OR REPLACEMENT
EVENT INCLUDE DAMAGES OF ANY KIND, WHETHER INCIDENTAL, CONSEQUENTIAL OR OTHERWISE.
NO GOODS ACCEPTED FOR RETURN WITHOUT PRIOR APPROVAL. Seller shall have the right to inspect any goods claimed to be defective at Buyers place of business or require Buyer to return the
goods to Seller for inspection on Seller’s premises. Transportation charges covering returned goods will be borne by Seller only if such goods are proven to be defective, are covered by this warranty
and are returned within the warranty period stated above.
PK-1740918
ASSEMBLY INSTRUCTIONS & PARTS MANUAL
RETAIN INSTRUCTIONS FOR FUTURE REFERENCE
Standard Storage Cabinet
Unassembled Model 1480 or CVD1480
Tennsco LLC., Dickson, TN 37056-1888 • (866) 446-8686
LOAD CAPACITIES PER SHELF LEVEL
36w x 24d 200 lbs.
UNIT SIZE WEIGHT CAPACITY
EVENLY DISTRIBUTED
ASSEMBLY OF 1480 or CVD1480 CABINET
Tools Needed: A free 11/ ” nut driver is included with each Tennsco cabinet. 32
Two people are recommended for assembly. Approximate assembly time: 30-40 minutes.
2. Place the cabinet back (Ref. No. 1) on a
protected surface to prevent
scratching the paint.
The ange on the
bottom of the back
should be facing upward.
1. The reference numbers used throughout this sheet refer
to the illustration on the back cover. This is to help you
to identify the various parts as they are mentioned.
3. Attach the left side (Ref. No. 2) to the back by placing
ange (A) around the back and bolting together with
seven bolts and nuts (Ref. Nos. 17 & 18). Be sure that the
lances on all shelf adjustment strips (B) are pointing in the
same direction.
5. Attach the right side (Ref. No. 3) to the back in the same manner
as you did in step 3, again, making sure that the ange is
around the back and that the lances on the shelf adjustment
strips are pointed in the same direction as those on the back and
left side. Push the side panel up so the studs in the top go
through the holes in the top
ange of the side and
fasten with three
nuts as in
step 4).
6. Attach the sill (Ref. No. 6) to the sides. Place nuts loosely on each
of the studs and slide the ends of the sill into the slots on both
sides of the unit. Then, securely tighten the nuts.
4. Attach the top (Ref. No. 5) to the unit by sliding the outer
ange over the back of the unit and the side ange on
the top over the side panel. The threaded studs should go
through the holes in the top
ange of the
side and
fasten with
three nuts.
Attach the
back to the
top using four
bolts and nuts.
7. Place the rear ange of the bottom (Ref. No. 7) into the
bottom lances of the back. The ange with two holes should
face the front, hanging over the sill. Insert the bolts through
the bottom and still with the head
facing the front of the unit.
Secure with
two nuts.
All lances point UP on
both backs and side.
Flange goes
under back.
Flange faces upward.
Flanges
face upward
Threaded studs go
through the holes
in the flange at the
top of the side.
Slide ends in to the slots
on the bottom of the sides.
Nuts placed loosely
on studs of the sill.
Insert bottom into
bottom lances.
B
A
NOTE: When bolting the unit together, leave
the bolts slightly loose until Step 8, unless
otherwise specified.
NOTE: All illustrations show a solid door. Assembly
for C-Thru doors (CVD1480) is identical.
Two holes must
be in front
8. Set the unit upright and tighten
all nuts around the entire unit.
10. Attach the left door
(Ref. No. 8) to the
unit by placing the
door on the hinges,
aligning the hinge
holes, and dropping
the hinge pins (Ref.
No. 15) into the slots.
Then, tap the top of
each hinge pin until
fully seated.
Leveler
Access Holes
9. Insert the four shelves (Ref. No. 4)
at your desired levels.
NOTE: In order to place the
shelves, you must first tilt
the shelf slightly to the left
or right before inserting
into the unit.
12. The cabinet must be
level in order for the
doors to close
properly. Levelers
may be adjusted by
placing the nut driver
through the hole in
each end of the sill
and adjusting the
leveling screw.
11. Attach the right door
(Ref. No. 9) to the unit
in the same way you
attached the left door.
1. Place the locking handle
(Ref. No. 11) on the right
hand door and fasten with
two #8-32 X 1/ 4hex-head
bolts and lock washers,
provided with the handle.
2. Turn the handle to the
open position and
place the locking cam
(Ref. No. 12) over the
square shank of the
door handle. The latch
must be facing downward
as shown. Then place the
locking cotter pin (Ref. No.
13) through the hole of the
square shank.
3. With the handle still in the open position, hook the
locking bars (Ref. No. 10) to the locking cam (see
“A” at left). Once in position, slowly rotate the door
handle to the closed position so the lock bars
prot rude from the holes at the top and bottom
of the door (shown at right, below).
4. Slide the nylon lock bar
guide inserts (Ref. No.
14) over the lock bar
ends and through the
door slots (see “B” at
right). Push down rmly
until the guides snap
into place.
Handle/Locking System Installation
A
B
B
Produktspezifikationen
| Marke: | Tennsco |
| Kategorie: | Kleiderschrank |
| Modell: | CVD1480 |
Brauchst du Hilfe?
Wenn Sie Hilfe mit Tennsco CVD1480 benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten
Bedienungsanleitung Kleiderschrank Tennsco
16 August 2024
14 August 2024
12 August 2024
12 August 2024
11 August 2024
10 August 2024
9 August 2024
9 August 2024
9 August 2024
9 August 2024
Bedienungsanleitung Kleiderschrank
- Kleiderschrank HP
- Kleiderschrank Powerfix
- Kleiderschrank IKEA
- Kleiderschrank Bush
- Kleiderschrank WOOOD
- Kleiderschrank Güde
- Kleiderschrank Kwantum
- Kleiderschrank Leen Bakker
- Kleiderschrank Livarno
- Kleiderschrank Ordex
- Kleiderschrank Profijt Meubel
- Kleiderschrank Tvilum
- Kleiderschrank United Office
- Kleiderschrank Habitat
- Kleiderschrank Foppapedretti
- Kleiderschrank JYSK
- Kleiderschrank BoConcept
- Kleiderschrank Bopita
- Kleiderschrank Flexa
- Kleiderschrank KidKraft
- Kleiderschrank Nolte
- Kleiderschrank Parisot
- Kleiderschrank Talgø
- Kleiderschrank Vipack
- Kleiderschrank Wehkamp
- Kleiderschrank Zuiver
- Kleiderschrank Miomare
- Kleiderschrank Woonexpress
- Kleiderschrank Bruynzeel
- Kleiderschrank Tiger
- Kleiderschrank Paidi
- Kleiderschrank Pali
- Kleiderschrank Safco
- Kleiderschrank APC
- Kleiderschrank Kirkton House
- Kleiderschrank Silver Cross
- Kleiderschrank Dutchbone
- Kleiderschrank Livarno Lux
- Kleiderschrank Butler
- Kleiderschrank Hooker
- Kleiderschrank BDI
- Kleiderschrank Calligaris .com
- Kleiderschrank Toomax
- Kleiderschrank Gladiator
- Kleiderschrank Arthur Berndt
Neueste Bedienungsanleitung für -Kategorien-
13 Oktober 2024
7 Oktober 2024
6 Oktober 2024
4 Oktober 2024
4 Oktober 2024
4 Oktober 2024
4 Oktober 2024
4 Oktober 2024
4 Oktober 2024
3 Oktober 2024