Teledex Pearl S Bedienungsanleitung

Teledex Telefon Pearl S

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Teledex Pearl S (2 Seiten) in der Kategorie Telefon. Dieser Bedienungsanleitung war für 31 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Download PDF

Seite 1/2

PACKAGE CONTENTS

Check to be sure that you have all of the following components in

your package (see figure below) :

• Telephone base unit • Handset coil cord • User guide

• Handset • Line cord

INSTALLATION

1) Plug one end of the handset coiled cord into the handset. Plug

the other end of the cord into the handset jack located on the

left side of the phone base. (Refer to diagram on reverse.)

2) Place the handset in the handset cradle. Plug one end of the line

cord into the jack on the back of your phone.LINE

3) Plug the other end of the modular cord into the wall jack.

WALL MOUNTING

The Pearl S telephone can easily be attached to a wall mount plate.

1) Remove the wall mount clip (located on the front of the

telephone, above the speaker grill) by firmly pushing upward

(toward the hook switch.)

2) Rotate the clip 180 degrees, so that the side with the protruding

edge is towards the top of the telephone. This edge will help

hold the handset on the cradle.

3) Place the handset in the handset cradle.

4) Connect the line cord into the jack on the back of your LINE

phone. Route the line cord through channel on the bottom of

the telephone. Connect the other end of the line cord to the

jack on the wall mount plate.

5) Slip the phone onto the wall plate; slide the telephone down

so it is firmly in place.

USING THE DATA PORT

The data port is located on the right hand side of the telephone. Use

this jack to connect a computer or fax machine in parallel to the

same phone line to which the telephone is connected.

ADJUSTING THE RINGER VOLUME

Your Pearl S telephone has two ringer volume levels: “Low” and

“High.” To adjust the ringer volume, slide the ringer volume switch

(located on the backside of the telephone) to the desired level.

HANDSET VOLUME CONTROL

There are three (3) volume levels for the handset volume. To increase

or decrease the handset volume, slide the handset volume switch

(located on the right hand side of the telephone) to the desired setting.

SPEAKER VOLUME CONTROL

To increase or decrease the speakerphone volume, move the speaker

volume slider control (located on the right hand side of the telephone)

until speaker volume is at a satisfactory level.

PLACING AND ANSWERING CALLS

To make a call, pick up the handset or press the key. WhenSPEAKER

you hear the dial tone, dial the desired phone number. To answer an

incoming call, pick up the handset or press the key. To end aSPEAKER

call, place the handset back on the base, or press the SPEAKER key

again.

SWITCHING BETWEEN HANDSET AND SPEAKERPHONE

To switch from the handset to the speakerphone during a call, press

the SPEAKER key, and place the handset on the base. To switch from

the speakerphone to the handset, lift the handset; the speakerphone

will automatically turn off.

USING REDIAL

The redial function allows you to redial the last dialed number. Pick

up the handset, or press the key, and press the SPEAKER REDIAL key. The

number will be dialed automatically.

USING FLASH

Flash supports custom calling services, such as call waiting. For

example, if you have subscribed to call waiting, press FLASH to answer

an incoming call, without disconnecting the current call. Press FLASH

again to return to the first call.

USING HOLD

To place a call on hold, press the HOLD key. The HOLD LED flashes.

You may now hang up the handset without disconnecting the call.

To resume the call, press the HOLD key again, or press the SPEAKER key.

The call will once again be active.

USING MUTE

Pressing the key will silence the handset or speakerphone micro-MUTE

phone. You will be able to hear the other party, but they will not be

able to hear you. The MUTE LED will light. Press the MUTE key again to

resume your conversation.

PROGRAMMING GUEST SERVICE KEYS

Follow these steps to program a number into one of the three memory

locations, for one-touch access to guest services, or for accessing

special PBX/Centrex services or features. Each memory location can

store up to sixteen (16) digits.

1) Lift the handset, then press the STORE key (For key location,

refer to diagram on reverse.)

2) On the dial pad, enter the number you wish to store. Once

you have entered the number completely, press the memory

button corresponding to the desired location.

DIALING A STORED NUMBER

Pick up the handset or press the key, wait for a dial tone,SPEAKER

then press the desired memory (guest service) key. The telephone will

automatically dial the stored number.

MESSAGE WAITING

The message waiting indicator flashes to indicate that there is a

message waiting. Consult your system administrator or service

provider for instructions on how to access these messages.

CARE AND MAINTENANCE

Your Pearl S telephone has been designed to provide years of trouble

free service. To ensure its longevity, please follow these maintenance

instructions:

1) Keep the Pearl S away from heat, as high temperatures can shorten

the life of the electrical components, and distort or melt plastic

parts.

2) The telephone should be kept free of dust and moisture. If it

gets wet, wipe it dry immediately. Liquids may contain minerals

that can corrode electronic circuits.

3) Handle your telephone gently and carefully. Dropping it can

cause serious damage to internal circuitry or the plastic case,

which may result in malfunction.

4) Do not use any type of chemical or abrasive powder to clean the

outer casing. Use only mild detergents on a soft, damp cloth to

clean the telephone.

5) In case of trouble with the telephone, do not attempt to repair

the telephone yourself. Contact your distributor for assistance.

If the trouble is affecting the telephone lines, the phone company

or service provider may ask you to disconnect the telephone

until the problem is resolved.

PEARL S

Guestroom Speakerphone

Users Guide

PACKAGE CONTENTS

BASE UNIT HANDSET

COIL CORD

LINE CORD USER GUIDE

REQUIREMENTS OF PART 68 - FCC RULES

This device has been granted a registration number by the Federal Communications Commission,

under Part 68 rules and regulations for direct connection to the telephone lines. In order to comply

with these FCC rules, the following instructions must be carefully read and applicable portions fol-

lowed completely:

1) Direct connection to the telephone lines may be made only through the standard modular cord

furnished, to the utility installed jack. No connection may be made to party or coin phone lines.

On the bottom of the phone is a label that contains, among other information, the FCC Registration

Number and the Ringer Equivalence number (REN) for this equipment. If requested this information

must be provided to the telephone company. The USOC Jack for this equipment is RJ11C.

2) The telephone company, under certain circumstances, may temporarily discontinue and make

changes in facilities and services which may affect the operation of the users' equipment. However,

the user shall be given adequate notice in writing to allow the user to maintain uninterrupted service.

3) In certain circumstances, it may be necessary for the telephone company to request information

from you concerning the equipment which you have connected to your telephone line. Upon request

of the telephone company, provide the FCC registration number and the ringer equivalence number

of the equipment which is connected to your line; this information will be found on the device.

4) If any of your telephone equipment is not operating properly, you should immediately remove it

from the telephone line. It may cause harm to the telephone network.

5) If the telephone company notes a problem, they may temporarily discontinue service. When practical,

they will notify you in advance of disconnection. If advance notice is not feasible, the telephone com-

pany must; promptly notify you of such temporary discontinuance; afford the opportunity to correct

the condition; inform you of your rights to bring a complaint to the FCC under their rules.

6) Repairs to the device may be made only by the manufacturer or an authorized service agency.

This applies at any time during and after warranty. If unauthorized repair is performed, registration,

connection to the telephone lines and remainder of warranty period all become null and void.

7) This equipment is hearing aid compatible.

REQUIREMENTS OF PART 15 - FCC RULES

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital

device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable pro-

tection against harmful interference in a residential installation. This equipment generates, uses, and

can radiate radio frequency energy and, if not installed and used in accordance with the instruction,

may cause harmful interference to radio communications. However, there is not a guarantee that

interference will not occur in a particular installation. If this equipment does cause harmful interference

to radio or television reception, which can be determined by turning the equipment off and on, the

user is encouraged to try to correct the interference by one or more of the following measures:

a) move the telephone away from the receiver. b) consult the dealer or an experienced radio/TV

technician for help. Any changes made by the user not approved by the manufacturer can void the

user's authorty to operate the telephone.

INDUSTRY OF CANADA REQUIREMENTS

NOTICE: The Industry Canada label identifies certified equipment. This certification means that the

equipment meets certain telecommunications network protective operational and safety requirements

as prescribed in the appropriate Terminal Equipment Technical Requirements documents. The

department does not guarantee the equipment will operate to the users satisfaction. Before installing

this equipment, users should ensure that it is permissible to be connected to the facilities of the local

telecommunications company. The equipment must also be installed using an acceptable method of

connection. The customer should be aware that compliance with the above conditions may not pre-

vent degradation of service in some situations. Repairs to certified equipment should be coordinated

by a representative designated by the supplier. Any repairs or alterations made by the user to this

equipment, or equipment malfunctions, may give the telecommunications company cause to request

the user to disconnect the equipment. Users should ensure for their own protection that the electrical

ground connections of the power utility, telephone lines, and internal metallic water pipe systems, if

present, are connected together. This precaustion may be particularly important in rural areas.

Caution: Users should not attempt to make such connections themselves, but should contact the

appropriate electric inspection authority or electrician, as appropriate. The Ringer Equivalence

Number (REN) of this device is z.

NOTICE: The Ringer Equivalence Number (REN) assigned to each terminal device provides an indi-

cation of the maximum number of terminals allowed to be connected to a telephone interface. The

termination on an interface may consist of any combination of devices subject only to the requirement

that the sum of the Ringer Equivalence Numbers of all the devices does not exceed 5. This

telephone connects to the telephone network under the connecting arrangement code CA11A.

IMPORTANT SAFETY INSTRUCTIONS

WHEN USING YOUR TELEPHONE EQUIPMENT, BASIC SAFETY PRECAUTIONS SHOULD

ALWAYS BE FOLLOWED TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK AND INJURY

TO PERSONS, INCLUDING THE FOLLOWING:

1. READ AND UNDERSTAND ALL INSTRUCTIONS.

2. FOLLOW ALL WARNINGS AND INSTRUCTIONS MARKED ON THE PRODUCT.

3. UNPLUG THE PRODUCT FROM THE WALL OUTLET BEFORE CLEANING. DO NOT USE

LIQUID CLEANER OR AEROSOL CLEANERS. USE A DAMP CLOTH FOR CLEANING.

4. DO NOT USE THIS PRODUCT NEAR WATER, FOR EXAMPLE: NEAR A BATHTUB, WASH

BOWL, KITCHEN SINK OR LAUNDRY TUB, IN A WET BASEMENT, OR NEAR A SWIMMING POOL.

5. DO NOT PLACE THIS PRODUCT ON AN UNSTABLE CART, STAND OR TABLE. THE PROD-

UCT MAY FALL, CAUSING SERIOUS DAMAGE TO THE PRODUCT.

6. SLOTS AND OPENINGS IN THE CABINET AND THE BACK OF BOTTOM ARE PROVIDED

FOR VENTILATION. THESE OPENINGS MUST NOT BE BLOCKED OR COVERED. THE

OPENINGS SHOULD NEVER BE BLOCKED BY PLACING THE PRODUCT ON A BED, SOFA,

RUG OR ANY OTHER SIMILAR SURFACE. THIS PRODUCT SHOULD NEVER BE PLACED

NEAR OR OVER A RADIATOR OR HEAT REGISTER. THIS PRODUCT SHOULD NOT BE

PLACED IN A BUILT-IN INSTALLATION UNLESS PROPER VENTILATION IS PROVIDED.

7. NEVER PUSH OBJECTS OF ANY KIND INTO THIS PRODUCT THROUGH CABINET SLOTS

AS THEY MAY TOUCH DANGEROUS VOLTAGE POINTS OR CAUSE A SHORT CIRCUIT THAT

COULD RESULT IN A FIRE OR ELECTRIC SHOCK. NEVER SPILL LIQUID OF ANY KIND ON

THE PRODUCT.

8. TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT DISASSEMBLE THIS PRODUCT.

IF SERVICE IS NECESSARY, SEND OR TAKE THE TELEPHONE TO A QUALIFIED SERVICE

FACILITY. OPENING OR REMOVING COVERS MAY EXPOSE YOU TO DANGEROUS VOLT-

AGES OR OTHER RISKS. INCORRECT REASSEMBLY CAN CAUSE ELECTRIC SHOCK

WHEN THE APPLIANCE IS SUBSEQUENTLY USED.

9. UNPLUG THIS PRODUCT FROM THE WALL OUTLET AND REFER SERVICING TO QUALI-

FIED SERVICE PERSONNEL UNDER THE FOLLOWING CONDITIONS:

• IF THE POWER SUPPLY CORD OR PLUG IS DAMAGED OR FRAYED

• ID LIQUID HAS BEEN SPILLED INTO THE PRODUCT

• IF THE PRODUCT HAS BEEN EXPOSED TO RAIN OR WATER

• IF THE PRODUCT DOES NOT OPERATE NORMALLY BY FOLLOWING THE

OPERATING INSTRUCTIONS. ADJUST ONLY THOSE CONTROLS THAT ARE

COVERED BY THE OPERATING INSTRUCTIONS, AS IMPROPER ADJUSTMENT OF

OTHER CONTROLS MAY RESULT IN DAMAGE AND WILL OFTEN REQUIRE

EXTENSIVE WORK BY A QUALIFED TECHNICIAN TO RESTORE THE PRODUCT TO

NORMAL OPERATION.

• IF THE PRODUCT HAS BEEN DROPPED OR THE CABINET HAS BEEN DAMAGED.

• IF THE PRODUCT EXHIBITS A DISTINCT CHANGE IN PERFORMANCE.

10. AVOID USING THE TELEPHONE DURING AN ELECTRICALSTORM. THERE MAY BE A

REMOTE RISK OF ELECTRIC SHOCK FROM LIGHTNING.

11. DO NOT USE THE TELEPHONE TO REPORT A GAS LEAK IN THE VICINITY OF THE

LEAK.

IF YOUR PRODUCT USES BATTERIES, FOLLOW THESE ADDITIONAL PRECAUTIONS:

1. USE ONLY THE TYPE AND SIZE OF THE BATTERY SPECIFIED.

2. DO NOT DISPOSE OF BATTERIES IN A FIRE. THE BATTERIES CAN OR MAY EXPLODE.

CHECK LOCAL CODES FOR PROPER BATTERY DISPOSAL INSTRUCTIONS.

Teledex, LLC

6311 San Ignacio Avenue

San Jose, CA 95119

Telephone: (408) 363-3100

Fax: (408) 363-3136

email: sales@teledex.com

Internet: www.teledex.com

Part Number: 600-0480-59

MAIN DIAGRAM RIGHT VIEW

LEFT VIEW

WALL MOUNTING

Handset Volume Speaker Volume

Handset Coil Cord

Handset Jack

Data Port

Cord Channel

Wall Jack

FOR CUSTOMER SERVICE CALL

1-800-783-8353

Wall Mount Clip

(under handset)

Handset

Ringer Volume

Data Port

Line Jack

Handset Volume

Mute Key

Redial Key

Flash Key

Speaker Volume

Store Key (hidden)

Guest Service Keys

Dial Pad

Speakerphone Key Hold Key Message Waiting Indicator

Produktspezifikationen

Marke:	Teledex
Kategorie:	Telefon
Modell:	Pearl S

Brauchst du Hilfe?

Wenn Sie Hilfe mit Teledex Pearl S benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten

Ihren Namen*

Deine E-Mail*

Schreiben Sie hier Ihre Frage

Bedienungsanleitung Telefon Teledex

Teledex A110 Bedienungsanleitung

7 September 2024

Teledex SIP ND2105 Bedienungsanleitung

18 August 2024

Teledex SIP LD4210S Bedienungsanleitung

18 August 2024

Teledex SIP ND2105S Bedienungsanleitung

18 August 2024

Teledex SIP ND2110 Bedienungsanleitung

18 August 2024

Teledex SIP ND2110S Bedienungsanleitung

18 August 2024

Teledex SIP LD4105S Bedienungsanleitung

18 August 2024

Teledex Opal 1003 Bedienungsanleitung

18 August 2024

Teledex SIP LD4205S Bedienungsanleitung

18 August 2024

Teledex Opal 1010S Bedienungsanleitung

18 August 2024

Bedienungsanleitung Telefon

Neueste Bedienungsanleitung für -Kategorien-

Gigaset SL370 Bedienungsanleitung

15 Oktober 2024

Profoon PDX-7020 Bedienungsanleitung

15 Oktober 2024

Profoon PDX-100 Bedienungsanleitung

14 Oktober 2024

Uniden XS 1415 Bedienungsanleitung

13 Oktober 2024

Uniden XDECT 6105BTU Bedienungsanleitung

11 Oktober 2024

OnePlus 9RT 5G Bedienungsanleitung

9 Oktober 2024

Profoon PDX-1520 Bedienungsanleitung

7 Oktober 2024

MT Logic TE-5740MTWG Bedienungsanleitung

7 Oktober 2024

D-Link DI-102 Bedienungsanleitung

6 Oktober 2024

Belgacom Specifics 100 Bedienungsanleitung

5 Oktober 2024