Teledex Opal 1005 Bedienungsanleitung
Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Teledex Opal 1005 (7 Seiten) in der Kategorie Telefone. Dieser Bedienungsanleitung war für 14 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet
Seite 1/7
OWNER’S
MANUAL
OPAL 1003
1005
1010
The Teledex one-line
telephones specifically
designed for the international
hospitality industry.
INCLUDED IN YOUR PACKAGE
Handset
Base Unit
Coiled Handset Cord
Line Cord
Clear Plastic Overlay
User Guide
CONNECTING THE OPAL TELEPHONE
1. Located on the left side of the Opal (as the phone is facing you) is a modular jack. Insert one end of the coiled
handset cord into this jack (you should hear the coil cord click when properly inserted).
2. Insert the other end of the coiled handset cord into the modular jack on the handset.
3. Turn the telephone so the back panel is facing you. Insert either end of the line cord into the jack on the back of
the telephone labeled LINE.
4. Insert the other end of the line cord into a telephone wall outlet jack.
5. Once your telephone is connected, remove the plastic overlay and place the paper faceplate over the keys.
Replace the plastic overlay by hooking the tabs on the overlay into the recessed slots located on both sides. The
overlay is easiest to insert when; the left or right side tabs are inserted first, and the middle of the overlay is
slightly bowed to allow for insertion of the other tabs.
PLACING A CALL
1. Lift the handset.
2. Listen for dial tone. Dial the desired number, or press an AUTO DIAL key to automatically dial a number.
3. To end the call, hang up by placing the handset back in the cradle.
RECEIVING A CALL
An audible ring and flickering red message waiting light will indicate an inbound call.
1. Lift the handset. The Opal will engage the ringing line.
2. To end the call hang up the handset.
ADJUSTING THE RING VOLUME
Locate the adjustment control on the back of the telephone labeled RINGER LOW/HI. Slide the switch to the
desired LOW or HI ring volume.
REDIAL
TO REDIAL THE LAST TELEPHONE NUMBER DIALED:
1. Lift the handset from the cradle.
2. Press the REDIAL key.
ADJUSTING THE HANDSET VOLUME
The HANDSET VOLUME key has three levels. When the handset is first lifted, the handset volume is NORMAL.
Locate the HANDSET VOLUME key below the keypad. Press the key once and the volume level will increase
one level (to MEDIUM volume). Press the key once more and the volume level will increase an additional level
(to HIGH volume). To return the handset volume to NORMAL , press the handset volume key again.
The handset volume will always return to NORMAL when the handset is replaced in the cradle.
FLASH KEY
Pressing the FLASH key initiates a 600ms hookflash. Typical usage is to access PBX features like call waiting.
AUTO DIAL KEYS
The Opal has programmable AUTO DIAL keys. These keys can be programmed to automatically dial telephone
numbers, or activate telephone system features.
PROGRAMMING AUTO DIAL KEYS:
The telephone must be connected to a telephone line.
1. Lift the handset from the cradle.
2. Press the recessed STORE key and release it. (Please see diagram on the next page).
3. Enter the telephone number including PAUSE* as required. The sequence can be up to 15 digits.
4. Press the AUTO DIAL key where the number is to be stored.
5. Place the handset back in the cradle.
*A 3.6 second pause is entered in a dialing sequence by pressing the REDIAL key for each PAUSE required.
CONVERTING FROM DESK TO WALL MOUNT
The Opal Telephone can be changed for wall mounting applications. The conversion is easiest when the handset
and line cords are not connected.
1. Located on the top of the telephone above the speaker grill is the wall/desk mount clip. Remove this clip by
firmly pushing upward (towards the hookswitch).
2. Flip the clip over (top to bottom) so that the protruding edge is towards the top of the phone. This edge will
hold the handset.
3. Turn the Opal over so the bottom is up facing you. Place the Opal on a nonabrasive surface to prevent scratch-
ing.
4. Locate and remove the mounting bracket, firmly push back and pull up to remove two of the four retaining tabs.
5. Rotate the mounting bracket 180 degrees clockwise so that the mounting eyelet on the bracket is facing in the
same direction as the other mounting eyelet located on the bottom of the telephone.
6. Insert the top two retaining tabs of the mounting brackets into the mounting bracket slots (located near the
middle of the telephone). Then firmly push down to insert the retaining tabs on the opposite side of the mounting
bracket.
7. Connect a short modular line cord into the jack on the back of the phone (labeled LINE). Route the line cord
thought the line cord channel. Connect the other end of line cord to the phone jack on the wall mounting plate.
8. Turn the telephone over, and slide the Opal down onto the mounting posts in downward direction. Both eyelets
should line up with the mounting posts.
9. Complete the wall mounting by installing the handset and handset cord.
Produktspezifikationen
| Marke: | Teledex |
| Kategorie: | Telefone |
| Modell: | Opal 1005 |
Brauchst du Hilfe?
Wenn Sie Hilfe mit Teledex Opal 1005 benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten
Bedienungsanleitung Telefone Teledex
12 Oktober 2024
12 Juli 2024
11 Juli 2024
11 Juli 2024
7 Juli 2024
7 Juli 2024
6 Juli 2024
5 Juli 2024
Bedienungsanleitung Telefone
- Telefone Panasonic
- Telefone Topcom
- Telefone Alcatel
- Telefone Audioline
- Telefone Auerswald
- Telefone Belgacom
- Telefone Doro
- Telefone Profoon
- Telefone Tiptel
- Telefone Logik
- Telefone Uniden
- Telefone Telstra
Neueste Bedienungsanleitung für -Kategorien-
11 Oktober 2024
10 Oktober 2024
9 Oktober 2024
13 Juli 2024
13 Juli 2024
12 Juli 2024
11 Juli 2024
10 Juli 2024
10 Juli 2024
10 Juli 2024