System Sensor SPWL Bedienungsanleitung

System Sensor Lautsprecher SPWL

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für System Sensor SPWL (4 Seiten) in der Kategorie Lautsprecher. Dieser Bedienungsanleitung war für 8 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Download PDF
Seite 1/4
1 I56-0001-002
10/02/2018
For use with the following models:
Wall Speakers: SPRL, SPWL
Ceiling Speakers: SPCRL, SPCWL
PRODUCT SPECIFICATIONS
Standard Operating Temperature: 32°F to 120°F (0°C to 49°C)
Humidity Range: 10 to 93% Non-condensing
Nominal Voltage: 25 Volts or 70.7 Volts
Maximum Supervisory Voltage: 50 VDC
Speaker Frequency Range: 400 – 4000 Hz
Power Settings: ¼, ½, 1, 2 Watts
Input terminal wire gauge: 12 to 18 AWG
PRODUCT DIMENSIONS MOUNTING BOX OPTIONS
WALL PRODUCTS Length Width Depth SPEAKERS
Wall Speaker 6.520" (165 mm) 5.00" (127 mm) 0.97" (24.6 mm) SBBSPRL/SBBSPWL (wall), SBBCRL/SBBCWL
(ceiling), 4" x 4" x 2
1
/
8"
or deeper
(When using 12AWG, 14 AWG, or adding extra
wires in the box, a deeper box or extension
ring is recommended.)
CEILING PRODUCTS Length Width Depth
Ceiling Speaker 6.8" (173 mm) N/A 1.00" (25.4mm)
NOTICE: This manual shall be left with the owner/user of this equipment.
BEFORE INSTALLING
Please read the System Sensor Voice Evacuation Application Guide, which
provides detailed information on speaker notification devices, wiring and
special applications. Copies of this manual are available from System Sensor.
NFPA 72 and NEMA guidelines should be observed.
Important: The notification appliance used must be tested and maintained
following NFPA 72 requirements.
GENERAL DESCRIPTION
System Sensor series of notification appliances offer a wide range of audible
and visible devices for life safety notification. Our line of speakers is designed
to be used at either 25 or 70.7 volts, and operate at any one of four input
power levels. Our speakers are suitable for dry and damp environments.
These products are electrically backwards compatible with previous genera-
tion of System Sensor speakers. With its low total harmonic distortion, the
System Sensor SPL series offers high fidelity sound output. Wall and ceiling
products may be used interchangeably (wall products may be used on ceiling
and ceiling product may be used on wall).
The speakers, and all power level settings, are listed to ANSI/UL 1480 require-
ments for public mode applications.
FIRE ALARM SYSTEM CONSIDERATIONS
All wiring must be installed in compliance with the National Electrical Code
(NEC) and applicable local codes. System Sensor recommends installing fire
alarm speakers in compliance with NFPA 72, ANSI/UL 1480 and NEC 760.
WIRING AND MOUNTING
All wiring must be installed in compliance with the National Electric Code
and the local codes as well as the authority having jurisdiction. Wiring must
not be of such length or wire size which would cause the notification appli-
ance to operate outside of its published specifications. Improper connections
can prevent the system from alerting occupants in the event of an emergency.
Wire sizes up to 12 AWG (2.5 mm²) may be used with the mounting plate. The
mounting plate ships with the terminals set for 12 AWG wiring.
Make wire connections by stripping about
3
/
8
" of insulation from the end of
the wire. Then slide the bare end of the wire under the appropriate clamping
plate and tighten the clamping plate screw.
See Figure 1 for wiring terminals and strip guide reference.
1. Connect the speaker. (See Figure 1.)
2. There are two rotary switches on the back of the product. The first switch
is used to select either 25 or 70.7 volts input and the second switch is used to
select the input power of ¼, ½, 1 or 2 watts. (See Figure 2.)
FIGURE 1. WIRING DIAGRAM AND WIRING TERMINALS
(-)
(+)
(-)
(+)
Input from
Amplifier
Output to
Next Device or EOL
A0380-02
Wiring Terminals
1. Negative (-). Line in and out
2. Positive (+). Line in and out
3. Positive (+). Line in and out
NOTE: Do not loop electrical wiring
under terminal screws. Wires
connecting the device to the control
panel must be broken at the device
terminal connection in order to
maintain electrical supervision.
FIGURE 2. SPEAKER WATTAGE AND VOLTAGE SETTINGS
A0419-01
INSTALLATION AND MAINTENANCE INSTRUCTIONS
3825 Ohio Avenue, St. Charles, Illinois 60174
800/736-7672, FAX: 630/377-6495
www.systemsensor.com
I56-0001-002
Dual Voltage Speakers
for Fire and ECS/MNS Systems
– Wall and Ceiling Mount
2 I56-0001-002
10/02/2018
MOUNTING AND REMOVING APPLIANCE
1. Attach mounting plate to junction box. (See Figures 4 and 5.)
2. Connect field wiring to terminals. (See Figure 1.)
3. If the product is not to be installed at this point, use the protective dust
cover to prevent contamination of the wiring terminals on the mounting plate.
4. To attach product to mounting plate:
a. Remove the protective dust cover.
b. Hook the tabs on the top of the product housing into the grooves on mount-
ing plate.
c. Pivot the product into position to engage the terminals on the mounting
plate. Make sure that the tabs on the back of the product housing fully en-
gage with the mounting plate.
d. Hold product in place with one hand, and secure product by tightening the
single mounting screw in the front of the product housing.
Ceiling Models only: To remove product from the mounting plate, loosen the
captive mounting screw and press the locking button.
CAUTION
The “hold in place” snaps are not intended to secure the product to the back
box. The product must be secured to the back box using the screws provided.
CAUTION
Factory finish should not be altered: Do not paint!
CAUTION
Do not over tighten mounting plate screws; this may cause mounting plate
to flex.
FIGURE 4. WALL SPEAKER
A0500-01
FIGURE 5. CEILING SPEAKER
A0501-02
Locking
Button
A0576-00
SHORTING SPRING FEATURE
System Sensor notification appliances come with a shorting spring that is pro-
vided between terminals 2 and 3 of the mounting plate to enable system con-
tinuity checks after the system has been wired, but prior to installation of the
final product. (See Figure 3.) This spring will automatically disengage when
the product is installed, to enable supervision of the final system.
FIGURE 3. SHORTING SPRING
Shorting
Spring
WIRING TERMINALS
1. Negative (-). Line in and out
2. Positive (+). Line in and out
3. Positive (+). Line in and out
Strip Guide
A0499-02
AVAILABLE POWER SETTINGS
System Sensor offers a wide range of power settings for your life safety needs,
including ¼, ½, 1, and 2W.
Sound levels data per UL 1480 can be found in Table 1. Directional character-
istics can be found in Table 2.
TABLE 1. SOUND LEVELS FOR EACH TRANSFORMER POWER SETTING
Setting UL Reverberant
(dBA @10 ft)
UL Anechoic
(dBA @10 ft)
¼ W 79 79
½ W 82 82
1 W 85 85
2 W 88 88
CAUTION
Signal levels exceeding 130% rated signal voltage can damage the speaker.
Consequently, an incorrect tap connection may cause speaker damage. This
means that if a 25V tap is selected when a 70.7V amplifier is being used,
speaker damage may result. Therefore, be sure to select the proper taps for the
amplifier voltage/input power level combination being used.
TABLE 2 DIRECTIONAL CHARACTERISTICS
Angle (degrees) Decibels
70° -3dB
90° -6dB
3 I56-0001-002
10/02/2018
TAMPER SCREW
For tamper resistance, the standard captive screw may be replaced with a Torx
screw (sold separately).
1. To remove the captive screw, back out the screw and apply pressure to the
back of the screw until it disengages from the housing. Replace with Torx
screw. (See Figure 6.)
FIGURE 6. TAMPER SCREW
T15 Torx
#6-32, 5/8"
SCREW-TMPR-50
A0502-01
NOTE: Wall speaker shown in this example.
INSTALLING A SURFACE MOUNT BACK BOX
1. The surface mount back box may be secured directly to the wall or ceiling.
Use of grounding bracket with ground screw is optional. (See Figures 7 and 8.)
2. The wall mount box must be mounted with the up arrow pointing up. (See
Figure 9.)
NOTE: Ceiling Surface Mount Back Box SBBCRL/CWL is a common back box
for ceiling horn strobes, strobes and ceiling speakers and speaker strobes. Use
the top mounting holes for ceiling speaker and speaker strobe products. (See
Figure 10.)
3. Threaded knockout holes are provided for the sides of the box for conduit
adapter. Knockout holes in the back of the box can be used for rear entry.
Wall-mount option supports ½ inch conduit; ceiling-mount option supports
½ inch or ¾ inch conduit.
4. To remove the ¾ inch knockout, place the blade of a flat-head screwdriver
along the outer edge and work your way around the knockout as you strike
the screwdriver. (See Figure 11.)
NOTE: Use caution not to strike the knockout near the top edge of the
surface mount back box.
5. V500 and V700 raceway knockouts are also provided. Use V500 for low
profile applications and V700 for high profile applications.
6. To remove the knockout, turn pliers up. (See Figure 12.)
FIGURE 7. SURFACE MOUNTING ON WALL (SBBSPRL, SBBSPWL)
A0503-01
FIGURE 8. SURFACE MOUNTING ON CEILING (SBBCRL, SBBCWL)
A0504-02
FIGURE 9. SURFACE MOUNT BACK BOX UP ARROW
A0481-00
FIGURE 10. CEILING INSTALLATION OF A SURFACE MOUNT BACK BOX :
KEY HOLE PATTERN
A0505-00
FIGURE 11 AND 12. KNOCKOUT REMOVAL FOR SURFACE MOUNT BACK
BOX AND WIRE MOLD REMOVAL
½ inch
or ¾ inch
Wire Mold Removal
A0465-01 A0466-01

Produktspezifikationen

Marke: System Sensor
Kategorie: Lautsprecher
Modell: SPWL

Brauchst du Hilfe?

Wenn Sie Hilfe mit System Sensor SPWL benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten


Bedienungsanleitung Lautsprecher System Sensor

System Sensor

System Sensor SPRK Bedienungsanleitung

13 August 2024
System Sensor

System Sensor SPCWK-R Bedienungsanleitung

13 August 2024
System Sensor

System Sensor SPR Bedienungsanleitung

10 August 2024
System Sensor

System Sensor SPWL Bedienungsanleitung

9 August 2024
System Sensor

System Sensor SPRL Bedienungsanleitung

21 Januar 2024

Bedienungsanleitung Lautsprecher

Neueste Bedienungsanleitung für -Kategorien-

Sonance

Sonance Visual Performance VP65 SST Bedienungsanleitung

16 Oktober 2024
Bowers And Wilkins

Bowers And Wilkins CWM664 Bedienungsanleitung

16 Oktober 2024
Focal

Focal Chorus 826 V Bedienungsanleitung

16 Oktober 2024
KEF

KEF Ci200ER Bedienungsanleitung

16 Oktober 2024
Steren

Steren SPK-1100BL Bedienungsanleitung

16 Oktober 2024
Aiwa

Aiwa SP-A100 Bedienungsanleitung

16 Oktober 2024
Trust

Trust GXT 628 Bedienungsanleitung

15 Oktober 2024
Pyle

Pyle PBMSPG6 Bedienungsanleitung

15 Oktober 2024
Marshall

Marshall Tufton Bedienungsanleitung

15 Oktober 2024
Sunstech

Sunstech SPUBT780 Bedienungsanleitung

15 Oktober 2024