Supermicro SuperServer 1018L-MP Bedienungsanleitung

Supermicro Nicht kategorisiert SuperServer 1018L-MP

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Supermicro SuperServer 1018L-MP (1 Seiten) in der Kategorie Nicht kategorisiert. Dieser Bedienungsanleitung war für 25 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Seite 1/1
http://www.supermicro.com MNL-1604-QRG
Board Layout
SuperServer 1018L-MP Quick Reference Guide
Power Button
2 x USB Ports
Audio Port
Description
No.
Drive bay Installation/RemovalMEMORY
Caution
1
2
3
SAFETY INFORMATION
IMPORTANT: See installation instructions and safety warning
before connecting system to power supply.
http://www.supermicro.com/about/policies/safety_information.cfm
WARNING:
To reduce risk of electric shock/damage to equipment,
disconnect power from server by disconnecting all power
cords from electrical outlets.
If any CPU socket empty, install protective plastic CPU cap
CAUTION:
Always be sure all power supplies for this system have
the same power output. If mixed power supplies are
installed, the system will not operate.
For more information go to :
http://www.supermicro.com/support
!
!
!
Position the SO-DIMM mod -1.
ule's bottom key so that it
aligns with the receptive point
on the slot . Take note of the
Module’s side notches
and the locking clips on the socket
Insert the SO-DIMM module 2.
staight down.
Press down until the module 3.
locks into place. The side clips
will automatically secure the
SO DIMM module, locking it
into place .
To 4. Remove: Use your thumbs
to gently push the side clips
near both ends away from the
module. This should release
it from the slot. Pull the SO
DIMM module upwards .
Installling 2.5" S A AT Drives
1. Power down the system and unplug the AC/DC Power Adapter.
2. Remove the chassis cover.
3. Use screws to secure the drive into the hard drive bracket.
4. Use screws to secure the bracket/drive assembly into the middle holding bar
of the chassis as shown in the figure.
Beep Codes
1 beep - circuits have been reset (ready to power up).
5 short beeps + 1 long beep - No memory detected
in the system
1 continuous beep with front panel Overheat LED on -
system overheat
5 short beeps - display memory error
When a recoverable type of error occurs during
POST, BIOS will display a POST code that
describes the problem. BIOS may also issue one
of the following beep codes:
Front View & Interface
In ion LEformat al D
S us t ntat Descrip io
Blue Power On
Blinking White HDD Activity
123
Descrip iot nNo.
PCI-E 2.0 p1-x16
Mini PCI-E scoket
JSD1 = SATA Disk on Module (DOM) Power
CPU socket
DIMMA1 Memory Slot
DIMMB1 Memory Slot
JTPM = TPM (Trusted Platform Management) Header
I-SATA2/3: SATA 2.0 ports (3Gb/s)
I-SATA0/1: SATA 3.0 ports (6Gb/s)
JBT1: CMOS Clear
1
2
3
4
5
6
7
8
9
10
5
6
1
I-SATA3
I-SATA2
JGPIO1
JPW2
JP1
JPCIE1
JSMB1
JBT1
BT1
COM4
COM
JAUDIO1
FAN2
FAN1
CA
JTPM1
JVR1
JL
JSD1
JD1
I-SATA0
I-SATA1
SP1
+
DIMMA1
DIMMB1
PW1
CMOS CLEAR
PCIE
mini
JUSB2LAN2 JUSBLAN1
42 3
10 7
89
A nlig
ÌMNL-1604-QRGcÎ


Produktspezifikationen

Marke: Supermicro
Kategorie: Nicht kategorisiert
Modell: SuperServer 1018L-MP

Brauchst du Hilfe?

Wenn Sie Hilfe mit Supermicro SuperServer 1018L-MP benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten




Bedienungsanleitung Nicht kategorisiert Supermicro

Bedienungsanleitung Nicht kategorisiert

Neueste Bedienungsanleitung für -Kategorien-