StarTech.com UDCMTRAY Bedienungsanleitung


Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für StarTech.com UDCMTRAY (2 Seiten) in der Kategorie Nicht kategorisiert. Dieser Bedienungsanleitung war für 8 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Seite 1/2
Quick-Start Guide
To view manuals, FAQs, videos, drivers, downloads, technical drawings, and more, visit www.startech.com/support.
Manual Revision: November 12, 2020
Product Diagram (UDCMTRAY)
Components Function
1Cable Tray Organizer Organize and hide Cables
Hide a Power Strip
2Mounting Holes/
Screws
Mount the underneath Cable Tray Organizer
a Desk
#12 Phillips® Head Screws
3Screwdriver Access
Holes
Cutouts that allow a Phillips Head
Screwdriver Phillips Head Drill Bit or a to
pass through the bottom of the Cable Tray
Organizer
Note: A long or a Phillips Head Screwdriver
Drill Bit Extension may be required to fasten the
Mounting Screws.
Requirements
For the latest requirements, please visit .www.startech.com/UDCMTRAY
#3 Phillips Head Screwdriver or a Power Drill with a Phillips Head Bit x 1
Power Drill with a Drill Bit x 1
Pencil x 1
(Optional) Drill Bit Extension x 1
Under Desk Cable Tray Organizer
Installation
Note: It is easier to complete the following installation steps with two people.
1. Hold the in the desired location under the , with the Cable Tray Organizer Desk
Mounting Holes Desk resting against the underside of the .
2. Mark the location of the using a .Mounting Holes Pencil
3. Use a with an appropriately sized to drill into the Power Drill Drill Bit Pilot Holes
locations of the .Mounting Holes
Notes: The should be the same depth as the length of the Pilot Holes Mounting
Screws Drill Bit . A small piece of tape can be placed on the to mark the proper depth
of the . Pilot Holes
The Drill Bit Desk size will be determined by the wood used to construct the . Consult a
professional if you are unable to determine the proper size.Drill Bit
4. Insert the through the and into the . Mounting Screws Mounting Holes Desk
(Figure 1)
5. Fasten the into the using a or a Screws Desk Phillips Head Screwdriver Power
Drill Phillips Head Bitwith a .
114mm
76mm
600mm
400mm
1
2
2
3
3
Use of Trademarks, Registered Trademarks, and other Protected Names and Symbols
This manual may make reference to trademarks, registered trademarks, and other protected names and/or symbols of third-
party companies not related in any way to StarTech.com. Where they occur these references are for illustrative purposes only
and do not represent an endorsement of a product or service by StarTech.com, or an endorsement of the product(s) to which
this manual applies by the third-party company in question. StarTech.com hereby acknowledges that all trademarks, registered
trademarks, service marks, and other protected names and/or symbols contained in this manual and related documents are the
property of their respective holders.
PHILLIPS® is a registered trademark of Phillips Screw Company in the United States or other countries.
Warranty Information
This product is backed by a two-year warranty.
For further information on product warranty terms and conditions, please refer to .www.startech.com/warranty
Limitation of Liability
In no event shall the liability of StarTech.com Ltd. and StarTech.com USA LLP (or their ocers, directors, employees or agents)
for any damages (whether direct or indirect, special, punitive, incidental, consequential, or otherwise), loss of prots, loss of
business, or any pecuniary loss, arising out of or related to the use of the product exceed the actual price paid for the product.
Some states do not allow the exclusion or limitation of incidental or consequential damages. If such laws apply, the limitations
or exclusions contained in this statement may not apply to you.
Safety Measures
If product has an exposed circuit board, do not touch the product under power.
Mesures de sécuri
Si l’un des circuits imprimés du produit est visible, ne pas touchez le produit lorsqu’il est sous tension.
安全対策
• 製品に露出した状態の回路基盤が含まれる場合、電源が入っている状態で製品に触らないでください
Misure di sicurezza
Se il prodotto ha un circuito stampato visibile, non toccare il prodotto quando è acceso.
Säkerhetsåtgärder
Rör aldrig vid enheter med oskyddade kretskort när strömmen är påslagen.
FR: fr.startech.com
DE: de.startech.com
ES: es.startech.com
NL: nl.startech.com
IT: it.startech.com
JP: jp.startech.com
StarTech.com Ltd.
45 Artisans Cres
London, Ontario
N5V 5E9
Canada
StarTech.com Ltd.
Unit B, Pinnacle 15
Gowerton Rd,
Brackmills
Northampton
NN4 7BW
United Kingdom
StarTech.com LLP
4490 South Hamilton
Road
Groveport, Ohio
43125
U.S.A.
Figure 1


Produktspezifikationen

Marke: StarTech.com
Kategorie: Nicht kategorisiert
Modell: UDCMTRAY

Brauchst du Hilfe?

Wenn Sie Hilfe mit StarTech.com UDCMTRAY benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten




Bedienungsanleitung Nicht kategorisiert StarTech.com

Bedienungsanleitung Nicht kategorisiert

Neueste Bedienungsanleitung für -Kategorien-