Spektrum DX2E Bedienungsanleitung

Spektrum Fernbedienung DX2E

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Spektrum DX2E (6 Seiten) in der Kategorie Fernbedienung. Dieser Bedienungsanleitung war für 13 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Download PDF

Seite 1/6

SPEKTRUM DX2E USER GUIDE

NOTICE

All instructions, warranties and other collateral documents are subject to change at the sole discretion of

Horizon Hobby, Inc. For up-to-date product literature, visit horizonhobby.com and click on the support tab for this product.

Meaning of Special Language

The following terms are used throughout the product literature to indicate various levels of potential harm when operating

this product:

NOTICE: Procedures, which if not properly followed, create a possibility of physical property damage AND a little or no

possibility of injury.

CAUTION: Procedures, which if not properly followed, create the probability of physical property damage AND a possibility

of serious injury.

WARNING: Procedures, which if not properly followed, create the probability of property damage, collateral damage, and

serious injury OR create a high probability of superficial injury.

INSTALLING THE

TRANSMITTER BATTERIES

BATTERY LED MONITOR

WARNING: Read the ENTIRE instruction manual to become familiar with the features of the product before operating.

Failure to operate the product correctly can result in damage to the product, personal property and cause serious injury.

This is a sophisticated hobby product and NOT a toy. It must be operated with caution and common sense and requires some

basic mechanical ability. Failure to operate this Product in a safe and responsible manner could result in injury or damage

to the product or other property. This product is not intended for use by children without direct adult supervision. Do not use

with incompatible components or alter this product in any way outside of the instructions provided by Horizon Hobby, Inc. This

manual contains instructions for safety, operation and maintenance. It is essential to read and follow all the instructions and

warnings in the manual, prior to assembly, setup or use, in order to operate correctly and avoid damage or serious injury.

WARNING AGAINST COUNTERFEIT PRODUCTS: Always purchase from a Horizon Hobby, Inc. authorized dealer to

ensure authentic high-quality Spektrum product. Horizon Hobby, Inc. disclaims all support and warranty with regards,

but not limited to, compatibility and performance of counterfeit products or products claiming compatibility with DSM or

Spektrum.

Age Recommendation: Not for Children under 14 years. This is not a toy.

NOTICE: This product is only intended for use with unmanned, hobby-grade, remote-controlled vehicles. Horizon Hobby

disclaims all liability outside of the intended purpose and will not provide warranty service related thereto.

WARRANTY REGISTRATION

Visit www.spektrumrc.com/registration today to register your product.

Solid Green Battery is good (Above 4V)

Flashing Green Battery voltage is critically low.

Replace batteries (below 4V)

2SPEKTRUM DX2E USER GUIDE

RECEIvER COMPATIBILITy

The DX2E is compatible with all Spektrum

™ DSMR™, DSM2®,

DSM® and Marine surface receivers.

RECEIvER CONNECTION

AND INSTALLATION

TyPICAL ELECTRIC INSTALLATION

TyPICAL GAS INSTALLATION

Install the Receiver in your vehicle using double-sided foam

servo tape. Foam servo tape will hold the receiver in place

and help isolate it from vibrations. Mount the antenna up

and away from the vehicle in an antenna tube. The higher

up the antenna is, the better signal it will receive.

CAUTION: Do not cut the antenna.

BINDING A RECEIvER

Binding is the process of programming the receiver to

recognize the GUID (Globally Unique Identifier) code of a

single specific transmitter. When a receiver is bound to

a transmitter, the receiver will only respond to that specific

transmitter. The DX2E and SR201 are bound at the factory,

but if you need to rebind for any reason, please follow

these steps:

1. With the receiver off, insert the bind plug into the BIND

port on the receiver.

2. Power the receiver through any other port. The green

LED will flash continuously, indicating the receiver is

in bind mode.

3. With the steering wheel and throttle trigger in the desired

preset failsafe positions (see the Failsafe section on this

page for more information), press and hold the bind

button and turn on the transmitter. The green LED on the

front of the transmitter will flash within three seconds,

indicating the transmitter is in bind mode. Release the

bind button when the green LED flashes. Continue to

hold the failsafe positions until the binding process

is complete.

Bind Button

BIND THST

N R N R

4. The LED on the receiver will glow solid when the

transmitter and receiver are bound.

5. Remove the bind plug and store it in a convenient place.

You must rebind when:

• Differentfailsafepositionsaredesirede.g.,whenthrottle

or steering reversing has been changed.

• Changingreceivertypese.g.,changingfromaDSM

receiver to a DSM2, DSMR or Marine receiver.

• Bindingthereceivertoadifferenttransmitter.

Some Spektrum receivers, like the SR3001, use a bind

button rather than a bind plug. The binding process is the

same with this receiver; however, instead of inserting the

plug before powering up the receiver, press and hold the

bind button while powering up the receiver to enter bind

mode.

FAILSAFE

Failsafe positions are also set during binding. In the unlikely

event that the radio link is lost during use, the receiver will

drive the servos to their preprogrammed failsafe positions

(normally full brakes and straight steering). If the receiver

is turned on prior to turning on the transmitter, the receiver

will enter failsafe mode. When the transmitter is turned on,

normal control is resumed. For more information on setting

the failsafe, refer to the Binding a Receiver section above.

Steering Servo

Throttle Servo

Battery

Receiver

Battery To Motor

Electronic

Speed Control

Receiver

Steering Servo

Throttle Port

Steering Port

Bind/Battery Port

Bind Plug

Antenna

LED

SPEKTRUM DX2E USER GUIDE

SERvO REvERSING

If a right steering command does not result in the wheels

turning right (and vice versa), the channel may need to be

reversed. To reverse a channel, switch the position of the

correlating switch—“N” is for normal, “R” is for reverse. You

can use a small screwdriver to move the switch if necessary.

STEERING TRIM

The steering trim dial is used to adjust the steering trim when

the wheel is centered. Rotating the dial changes the steering

trim (the steering at rest position). Normally, the steering trim

is adjusted until the vehicle tracks straight.

ThROTTLE TRIM

The throttle trim dial is used to adjust the throttle trim when

the throttle stick is released (neutral position). This is typically

used to adjust the brakes. Rotating the dial causes the

throttle trim (the throttle position at rest) to be changed.

ChANGING ThE TRAvEL ADjUST

SETTINGS

The travel function supports precise endpoint adjustments in

each direction for the steering and throttle channels.

1. Hold the trigger in the full brake position while powering

on the transmitter. The LED flashes rapidly, indicating the

programming mode is active.

2. Throttle End Point: Hold the trigger in the full throttle position.

Turn the TH TRIM knob to adjust the full throttle end point.

3. Brake End Point: Hold the trigger in the full brake position. Turn

the TH TRIM knob to adjust the full brake end point. Return

the trigger to the center position.

4. Left Steering End Point: Hold the steering wheel in the full left

position. Turn the ST TRIM knob to adjust the left end point.

5. Right Steering End Point: Hold the steering wheel in the full

right position. Turn the ST TRIM knob to adjust the right end

point. Return the steering wheel to the center position.

6. Power off the transmitter to save the travel adjust settings. The

minimum Travel is 75%, and the Maximum travel is 150%.

The default travel settings are 125% steering and

100% throttle.

IMPORTANT: If the travel is changed on the DX2E, you must

rebind and calibrate AVC™ Receivers.

STEERING RATE AND GAIN CONTROL

Steering rate (also known as dual rate) allows on-the-fly

steering travel adjustments to be made using the ST Rate

dial. Steering rate limits the amount of travel of the steering

servo. The steering rate cannot be greater than 100%.

When the DX2E is bound to a DSMR AVC receiver, the ST

RATE knob controls the sensor gain value. Turn the knob

counterclockwise to reduce the gain or clockwise to increase

the gain.

R.O.S.S. START BUTTON

The transmitter BIND button also functions as a Remote

On-Board Starting System (R.O.S.S.) button. To use the R.O.S.S.

button:

1. Connect the R.O.S.S. system to the AUX 1 port on the

receiver.

2. Press and hold the R.O.S.S. button to activate the system.

SAFETy PRECAUTIONS

• Alwaysensureallbatterieshavebeenproperlycharged

prior to using the model.

• Alwayscheckallservosandtheirconnectionspriorto

each run.

• Neveroperateyourmodelnearspectators,parkingareas

or any other area that could result in injury to people or

damage of property.

• Neveroperateyourmodelduringadverseweather

conditions. Poor visibility can cause disorientation and loss

of control of your model.

• Neverpointthetransmitterantennadirectlytowardthe

model. The radiation pattern from the tip of the antenna

is inherently low.

• Ifatanytimeduringtheoperationofyourmodelyou

observe any erratic or abnormal operation, immediately

stop operation of your model until the cause of the

problem has been ascertained and corrected.

Reverse Switch

Steering

Reverse Switch

Throttle

BIND THST

N R N R

Steering Trim Dial

Throttle Trim Dial

Steering

Rate Dial

Produktspezifikationen

Marke:	Spektrum
Kategorie:	Fernbedienung
Modell:	DX2E
Gewicht:	- g
Produktfarbe:	Schwarz
Akku-/Batterietyp:	AA
Akku-/Batterietechnologie:	Alkali
Eingebautes Display:	Nein
Ein-/Ausschalter:	Ja
Frequenzband:	2.4 GHz
Schnittstelle:	RF Wireless
Maximale Reichweite:	- m
Wiederaufladbar:	Ja
Fernbedienung Nutzung:	Spielekonsole
Eingangssignal:	Drucktasten