SpeakerCraft CRS8 Two Bedienungsanleitung

SpeakerCraft Lautsprecher CRS8 Two

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für SpeakerCraft CRS8 Two (4 Seiten) in der Kategorie Lautsprecher. Dieser Bedienungsanleitung war für 6 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Download PDF

Seite 1/4

OWNER’S MANUAL

SPEAKER PLACEMENT

Before installing your speakers, you should consider the place-

ment carefully, taking into account the location of electrical,

plumbing and other ﬁxtures. Contact your dealer for assis-

tance if you are not sure of the best location in your particular

room environment.

Placement In Ceiling: When placing your speakers in the

ceiling, they should ideally be located above the primary

listening area. The unique tweeter bafﬂe of the CRS8 speakers

allows for more forward radiation and a more even frequency

response than is obtainable on conventional coaxial type round

speakers. (See Diagram 1) If the speakers are positioned far away from the primary listening area, adjust the pivoting

tweeter so they are pointed at the primary listening area. Note: To avoid possible damage to the pivoting tweeters,

read the section entitled “SPEAKER ADJUSTMENTS” in this manual prior to performing the tweeter adjustment.

In a very large room with high ceilings, it may be necessary to place additional speakers throughout the room.

Contact your Authorized SpeakerCraft dealer for assistance.

MOUNTING SURFACE PREPARATION

New Construction — Unﬁnished Ceilings

A New Construction Bracket, SpeakerCraft P/N BKT90681 (available from your dealer), may be installed prior to

drywall application across joists (up to 24" on-center) where a speaker will be located. Insulation material should

be in place prior to installing drywall. After the hole is cut and the drywall is installed, the speakers are then eas-

ily installed following the instructions for mounting in “Finished Ceilings”.

Note: If the speakers are to be mounted

more than 24" on-center, a special “Extra Long Wing”, SpeakerCraft P/N WING90224, is available from your dealer.

Finished Ceilings

Prior to the actual installation of the speakers, it will be necessary to run cables to the speaker locations. See your

dealer for more information about cable installation. After the cable has been properly installed, you are ready to

mount the speakers. Following the simple steps listed below will result in a professional looking installation:

1. Determine the best area to mount your speakers. This area of the ceiling should be free of obstructions such as

electrical conduit, HVAC ducts, or water lines. This can best be determined by noting the placement of ﬁxtures

and gaining access to an attic or crawl space for further analysis of the location of such obstacles.

2. Find the joists nearest the desired speaker mounting location. We highly recommend using a good stud-ﬁnder

tool for this procedure. If you are lining up the speakers to some other object or molding in the room, make

sure you consider the size of the bafﬂe ﬂange which extends beyond the mounting hole.

3. Mark the hole. A template for setting the hole is provided in the box (along with two paint mask inserts for use

when painting). Position the template in the desired position and pencil an outline on the ceiling.

Congratulations on your purchase of SpeakerCraft CRS8 In-Ceiling Speakers. All CRS8 speakers

are equipped with pivoting tweeters, which allow you to direct the sound toward, or away from,

a listening area to achieve a desired effect. In addition, each CRS8 model features SpeakerCraft’s

revolutionary WavePlane™ tweeter bafﬂe. SpeakerCraft has a wide variety of accessories to com-

pliment your CRS Series speakers. Contact your dealer or SpeakerCraft direct for more details.

Diagram 1

WavePlane

™

Technology

95% Solid Plane for Tweeter

80% Open Area for Woofer

Even dispersion, less distortion

Standard Co-Axial

No Tweeter Bafﬂe

Uneven Forward Dispersion

which causes distortion

Custom Round Series In-Ceiling Loudspeakers

CRS8 SERIES

CRS8 One / CRS8 Two / CRS8 Three / CRS8 Four

Page 2 Eazy6 Owner’s Manual Page 2 CRS8 Owner’s Manual

4. Cutting the hole. CAUTION: This is the most important part of the entire

installation. If you are uncertain whether any obstructions exist behind the desired

mounting area, you should start by cutting a small hole in the center of your

penciled mounting hole with a drywall saw, cutting at a 45º angle towards the

inside of the hole.

(See Diagram 2) Cutting the small hole at this angle will make

drywall repair much easier, using the piece cut out. Once you have determined

that there aren’t any obstructions in your desired mounting location, start cutting

the ﬁnished hole at a 90º angle to the ceiling surface.

5. Add insulation. If the area in the ceiling is not already insulated, add an adequate

amount insulation material to loosely cover the back of the speaker. If the insulation

material used is faced with foil or paper, position the foil or paper away from the

speaker.

SPEAKER ADJUSTMENTS

Your CRS8 speakers come from the factory with the tweeter facing straight out from

the bafﬂe. This will result in the overall smoothest response. However, depending

on your particular primary area, room acoustics, ceiling height, or personal prefer-

ence, you may ﬁnd the sound more pleasing by pointing the tweeters in a particu-

lar direction. If additional treble is desired in the primary listening area, point the

tweeter towards that area; and if less treble is required, point the tweeter away. Push

gently at the edge of the tweeter to point it in the desired direction.

(See Diagram 3)

CAUTION: Avoid touching tweeter dome as damage WILL occur on metal dome

tweeters (CRS8 Three & Four).

Treble Adjustment (CRS8 Two, Three & Four):

The switch labeled TREBLE allows for 6dB of treble (high frequency) adjustment. Your speakers were

shipped with the treble switch in the neutral position, providing the most linear frequency response. If you

desire more treble, roll the switch to the “+” position, and the tweeter will play 3dB higher. If you want less

treble, roll the switch to the “-” position and the tweeter will play 3dB lower. To return to the neutral setting,

slide the switch to the middle position. (See Diagram 4)

Bass Adjustment (CRS8 Three & Four):

The switch labeled BASS allows for 6dB of bass (low frequency) adjustment. Your speakers were shipped

with the bass set to neutral, resulting in 6Ω of impedance. This setting provides the ﬂattest bass frequency

response. If you desire more bass, roll the switch towards “+” and the bass will play 3dB higher and lower

the impedance to 4Ω. If you want less bass, roll the switch towards “-” and the bass will play 3dB lower and

increase the impedance to 8Ω. This setting provides a more linear bass frequency response. To return to the

neutral setting, slide the switch to the middle position. (See Diagram 5) Remember that altering the imped-

ance affects the number of speakers able to be driven by an ampliﬁer. If multiple pairs of speakers are to be

driven by one ampliﬁer, SpeakerCraft suggests using the lowest output position (switch rolled towards the “-”

position) until it is determined that the ampliﬁer will operate properly with the speakers switched to a high- er

output mode. If you want to safely operate multiple pairs of speakers, consider purchasing SpeakerCraft S4 or S8

Speaker Selectors.

SPEAKER INSTALLATION

Note: Your CRS8 Series speakers may have come with the optional Jawz ™ speaker wire connector. Before

using Jawz™, please follow the instructions included with the connector.

The unique integral four foot mounting system incorporated into each CRS8 speaker allows for a quick

installation by following these easy steps:

1. Remove the grille. It may be necessary to push one or two of the mounting screws and its attached foot

towards the bafﬂe and against the inside surface of the grille to force the grille out of its retaining groove.

2. Attach the speaker cable (observing the proper polarity with your ampliﬁer, + to + and - to - ).

Make sure the left channel of the ampliﬁer is connected to the left speaker, and the right channel is

connected to the right speaker.

3. Make sure the mounting feet are turned inward to clear the opening, and insert the speak- er

Diagram 2:

Ceiling Cut Out

Diagram 3:

Tweeter

Diagram 5:

Bass Adjustment Switch

Diagram 4:

Treble Adjustment Switch

Push Tweeter Here

Page 2 Eazy6 Owner’s Manual CRS8 Owner’s Manual Page 3

into the ceiling. Position the speaker into the hole. The ﬂange of the speaker is designed Note:

to ﬂex and conform to any small imperfections in the ceiling’s surface. Tighten the four screws

on the front of the bafﬂe only enough to make the ﬂange become snug against the ceiling. As

you tighten the screws, the feet will automatically ﬂip into an outward position

(See Diagram

6), thereby clamping the drywall between the feet and the ﬂange. CAUTION: Over tightening

may warp the bafﬂe, crack the ceiling, cause ﬂange to distort, and make the grille difﬁcult

to install.

4. Push the grille ﬁrmly into the slot in the speaker bafﬂe.

PAINTING THE SPEAKERS

If you plan to paint your speakers, we recommend that it be done prior to installation. If

you plan to paint your speakers sometime in the future, it is best to remove them by simply

reversing the steps for “SPEAKER INSTALLATION” on page 2. If it is necessary to paint the speakers

while they are still in the ceiling, the paint masks provided in the carton must be installed in place

of the grille while the ﬂange is being painted with the ceiling. The grilles can also be painted,

however, great care should be taken not to clog the holes, as this will greatly reduce the sound

quality of the speakers. Before painting the grilles, remove the under grille material. Put this mate-

rial back into place once the grille has been painted. SpeakerCraft recommends only light spray

painting, using 5 parts thinning agent to 1 part paint. Do not paint the grilles while they are

attached to the speaker. If it is necessary to paint the under grille material, follow the same

procedure used to paint the grilles.

SPECIAL FIRE WALL INSTALLATION

If you plan to mount your speakers in a ﬁre-rated ceiling, you should purchase SpeakerCraft 8" Round Sound Enclosures, model #SE1410. The

metal enclosures mount easily between joists, and contain a standard electrical type connector for connections of your speaker cable directly

to the speaker.

Diagram 6:

Mounting Feet

LIMITED LIFETIME WARRANTY

SpeakerCraft Inc. warrants to the original retail purchaser that this SpeakerCraft product will be free from defects in materials and workmanship, provided only

the speaker was purchased from a SpeakerCraft Authorized Dealer.

Defective products must be shipped, together with proof of purchase, prepaid insured to the SpeakerCraft Authorized Dealer from whom they were purchased,

or to the SpeakerCraft factory at the address listed on this installation instruction manual. Freight collect shipments will be refused. It is preferable to ship this prod-

uct in the original shipping container to lessen the chance of transit damage. In any case, the risk or loss or damage in transit is to be borne by the purchaser. If,

upon examination at the Factory or SpeakerCraft Authorized Dealer, it is determined that the unit was defective in materials or workmanship at any time during

this warranty period, SpeakerCraft or the SpeakerCraft Authorized Dealer will, at its option, repair or replace this product at no additional charge, except as set

forth below. If this model is no longer available and can not be repaired effectively, SpeakerCraft, at its sole option may replace the unit with a current model of

equal or greater value. In some cases where a new model is substituted, a modiﬁcation to the mounting surface may be required. If mounting surface modiﬁca-

tion is required, SpeakerCraft assumes no responsibility or liability for such modiﬁcation. All replaced parts and product become the property of SpeakerCraft Inc.

Products replaced or repaired under this warranty will be returned to the original retail purchaser, within a reasonable time, freight prepaid.

This Warranty does not include service or parts to repair damage caused by accident, disaster, misuse, abuse, negligence, inadequate packing or shipping

procedures, commercial use, voltage inputs in excess of the rated maximum of the unit, or service, repair or modiﬁcation of the product which has not been

authorized or approved by SpeakerCraft. This Warranty also excludes normal cosmetic deterioration caused by environmental conditions. This Warranty will be

void if the Serial Number on the product has been removed, tampered with or defaced.

This Warranty is in lieu of all other expressed warranties. If the product is defective in materials or workmanship as warranted above, the purchaser’s sole remedy

shall be repair or replacement as provided above. In no event will SpeakerCraft be liable for any incidental or consequential damages arising out of the use or

inability to use the product, even if SpeakerCraft Inc. or a SpeakerCraft Inc. Authorized Dealer has been advised of the possibility of such damages, or for any

claim by any other party. Some states do not allow the exclusion or limitation of consequential damages, so the above limitation and exclusion may not apply.

All implied warranties on the product are limited to the duration of this expressed Warranty. Some states do not allow limitation on the length of an implied

warranty. If the original retail purchaser resides in such a state, this limitation does not apply.