Sony XDR-DS12iP Bedienungsanleitung
Lesen Sie kostenlos die π deutsche Bedienungsanleitung fΓΌr Sony XDR-DS12iP (4 Seiten) in der Kategorie Receiver. Dieser Bedienungsanleitung war fΓΌr 6 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet
Seite 1/4
WARNING
To reduce the risk of fire or electric shock, do
not expose this apparatus to rain or
moisture.
To reduce the risk of fire, do not cover the
ventilation of the apparatus with newspapers,
tablecloths, curtains, etc. And do not place lighted
candles on the apparatus.
To reduce the risk of fire or electric shock, do not
expose this apparatus to dripping or splashing,
and do not place objects filled with liquids, such
as vases, on the apparatus.
Do not install the appliance in a confined space,
such as a bookcase or built-in cabinet.
Do not expose the batteries (battery pack or
batteries installed) to excessive heat such as
sunshine, fire or the like for a long time.
As the main plug is used to disconnect the unit
from the mains, connect the unit to an easily
accessible AC outlet. Should you notice an
abnormality in the unit, disconnect the main plug
from the AC outlet immediately.
The unit is not disconnected from the AC power
source (mains) as long as it is connected to the
wall outlet, even if the unit itself has been turned
off.
The nameplate and important information
concerning safety are located on the bottom
exterior.
CAUTION
Danger of explosion if battery is incorrectly
replaced. Replace only with the same type.
Notice for customers: the following
information is only applicable to equipment
sold in countries applying EU directives
The manufacturer of this product is Sony
Corporation, 1-7-1 Konan, Minato-ku, Tokyo,
108-0075 Japan. The Authorized Representative
for EMC and product safety is Sony Deutschland
GmbH, Hedelfinger Strasse 61, 70327 Stuttgart,
Germany. For any service or guarantee matters,
please refer to the addresses given in separate
service or guarantee documents.
Precautions
ξξ
Operate the unit on the power source specified
in βSpecifications.β
ξξ
Since a strong magnet is used for the speaker,
keep personal credit cards using magnetic coding
or spring-wound watches away from the unit to
prevent possible damage from the magnet.
ξξ
Do not leave the unit in a location near a heat
source such as a radiator or airduct, or in a
place subject to direct sunlight, excessive dust,
mechanical vibration, or shock.
ξξ
Allow adequate air circulation to prevent internal
heat build-up. Do not place the unit on a surface
(a rug, a blanket, etc.) or near materials (a
curtain) which might block the ventilation holes.
ξξ
Should any solid object or liquid fall into the unit,
unplug the unit and have it checked by qualified
personnel before operating it any further.
ξξ
To clean the casing, use a soft cloth dampened
with a mild detergent solution.
ξξ
Never touch the wire of the external aerial
during a thunderstorm. Furthermore,
immediately disconnect the AC power cord
from the radio.
NOTES ON LITHIUM BATTERY
ξξ
Wipe the battery with a dry cloth to assure a
good contact.
ξξ
Be sure to observe the correct polarity when
installing the battery.
ξξ
Do not hold the battery with metallic tweezers,
otherwise a short-circuit may occur.
Disposal of Old Electrical &
Electronic Equipment
(Applicable in the European
Union and other European
countries with separate
collection systems)
This symbol on the product or on its packaging
indicates that this product shall not be treated as
household waste. Instead it shall be handed over
to the applicable collection point for the recycling
of electrical and electronic equipment. By
ensuring this product is disposed of correctly, you
will help prevent potential negative consequences
for the environment and human health, which
could otherwise be caused by inappropriate waste
handling of this product. The recycling of
materials will help to conserve natural resources.
For more detailed information about recycling of
this product, please contact your local Civic
Office, your household waste disposal service or
the shop where you purchased the product.
Applicable accessory: Remote Commander.
Disposal of waste batteries
(applicable in the European
Union and other European
countries with separate
collection systems)
This symbol on the battery or on the packaging
indicates that the battery provided with this
product shall not be treated as household waste.
On certain batteries this symbol might be used in
combination with a chemical symbol. The
chemical symbols for mercury (Hg) or lead (Pb)
are added if the battery contains more than
0.0005% mercury or 0.004% lead.
By ensuring these batteries are disposed of
correctly, you will help prevent potentially
negative consequences for the environment and
human health which could otherwise be caused
by inappropriate waste handling of the battery.
The recycling of the materials will help to
conserve natural resources.
In case of products that for safety, performance or
data integrity reasons require a permanent
connection with an incorporated battery, this
battery should be replaced by qualified service
staff only.
To ensure that the battery will be treated properly,
hand over the product at end-of-life to the
applicable collection point for the recycling of
electrical and electronic equipment.
For all other batteries, please view the section on
how to remove the battery from the product
safely. Hand the battery over to the applicable
collection point for the recycling of waste
batteries.
For more detailed information about recycling of
this product or battery, please contact your local
Civic Office, your household waste disposal
service or the shop where you purchased the
product.
If you have any questions or problems concerning
your unit, please consult your nearest Sony dealer.
Features
ξξ
DAB/DAB+/FM Tuner
ξξ
Wake or Sleep to iPod/Radio
ξξ
MEGA BASS/MEGA Xpand
ξξ
Dual Alarm (A/B)
ξξ
Brightness control (High/Middle/Low/OFF)
ξξ
Wireless Remote Commander
ξξ
No Power No Problem alarm system to keep
the clock and the alarm operating during a
power interruption with a CR2032 battery
installed.
Specifications
Time display
Switching between 12-hour system (default) and
24-hour system
Section for iPod
DC out: 5V
MAX: 500mA
Radio section
Frequency range
Band Frequency Channel step
DAB
(Band-III)
174.928 MHz -
239.200 MHz
FM 87.5 MHz -
108 MHz
0.05 MHz
DAB (Band-III) frequency table (MHz)
No. Channel Frequency
1 5A 174.928
2 5B 176.640
3 5C 178.352
4 5D 180.064
5 6A 181.936
6 6B 183.648
7 6C 185.360
8 6D 187.072
9 7A 188.928
10 7B 190.640
11 7C 192.352
12 7D 194.064
13 8A 195.936
14 8B 197.648
15 8C 199.360
16 8D 201.072
17 9A 202.928
No. Channel Frequency
18 9B 204.640
19 9C 206.352
20 9D 208.064
21 10A 209.936
22 10B 211.648
23 10C 213.360
24 10D 215.072
25 11A 216.928
26 11B 218.640
27 11C 220.352
28 11D 222.064
29 12A 223.936
30 12B 225.648
31 12C 227.360
32 12D 229.072
33 13A 230.784
34 13B 232.496
35 13C 234.208
36 13D 235.776
37 13E 237.488
38 13F 239.200
General
Speaker
Approx. 5.7 cm (2 1/4 inches) dia. 6 Ξ©
Input
AUDIO IN jack (ΓΈ 3.5 mm stereo minijack)
Power output
3.5 W + 3.5 W (at 10% harmonic distortion)
Power requirements
230 V AC, 50 Hz
For clock back up: 3V DC, CR2032 battery (1)
Dimensions
Approx. 290.5 mm Γ 152.0 mm Γ 139.5 mm (w/h/d)
(11 3/8 inches Γ 5 15/16 inches Γ 5 1/2 inches)
including projecting parts and controls
Mass
Approx. 1.7 kg (3 lb 12 oz) including power
supply unit
Supplied accessories
Remote commander (1)
Audio connecting cable (1)
Universal Dock Adapter for iPhone (1)
Universal Dock Adapter for iPhone 3GS & iPhone
3G (1)
Universal Dock Adapter for iPhone 4S & iPhone 4
Design and specifications are subject to change
without notice.
Compatible iPod/iPhone
models
Compatible iPod/iPhone models are as follows.
Update your iPod/iPhone to use the latest
software before you use it.
iPod touch (4th generation)
iPod touch (3rd generation)
iPod touch (2nd generation)
iPod touch (1st generation)
iPod nano (6th generation)*
iPod nano (5th generation)
iPod nano (4th generation)
iPod nano (3rd generation)
iPod nano (2nd generation)
iPod nano (1st generation)
iPod with video
iPod with color display
iPod with click wheel
iPod classic
iPod mini
iPhone 4S
iPhone 4
iPhone 3GS
iPhone 3G
iPhone
* The iPod nano (6th generation) cannot be
controlled when the command of β ,β β ,β MENU ξ
¬
β ,β and β β is pressed.ξENTER
Notes
ξξ
In these Operating Instructions, βiPodβ is used
as a general reference to functions of iPod on an
iPod or iPhone, unless otherwise specified by
the text or illustrations.
ξξ
The connector of the unit is for sole use with an
iPod. If you use devices that do not match with
the connector, connect to the AUDIO IN jack of
this unit with the supplied audio connecting
cable.
ξξ
Sony cannot accept responsibility in the event
that data recorded to an iPod is lost or damaged
when using an iPod connected to this unit.
4-199-738- (1)14
To replace the battery
1 Keep the AC plug connected to the AC
outlet, remove the screw that secures the
battery compartment lid at the bottom of
the unit using a screwdriver, and open
the lid (see Fig. ).ξ
2 Remove the old battery and insert a new
one in the battery compartment with the
ξ³ ξ side facing up (see Fig. ).
3 Replace the battery compartment lid and
secure it with the screw (see Fig. ).ξ
4 Press iPod & iPhone DAB/FM ,ξ,
AUDIO IN SNOOZE/DATE/SLEEPor
OFF to turn β β off in the display.ξ
Note
Do not disconnect the plug from the AC outlet,
when you replace the battery. Otherwise, the
calendar, current time, alarm settings and station
presets will be erased.
ξ
ξ
Reset button
with the side ξ³
facing up
ξ
ξ
Ά
If the time in the display is
incorrect after the battery is
changed (Reset)
Press the reset button with a pointed device. The
reset button is in the small hole located in the
battery compartment (see Fig. ). ξ
Setting the clock for
the first time
When the first time after purchase, do the
following.
Troubleshooting
Should any problem persist after you have made
the following checks, consult your nearest Sony
dealer.
The clock flashes βAM 12:00β or β0:00β due to
a power interruption.
ξξ
The battery is low. Replace the battery. Remove
the old battery and install a new one.
ξξ
Make sure to remove the insulation film of the
backup battery before use.
The alarm of radio, iPod or buzzer does not
sound at the preset alarm time.
ξξ
Check that alarm βAβ or alarm βBβ is properly
displayed.
The alarm of radio or iPod is activated but no
sound comes on at the preset alarm time.
ξξ
Check the alarm volume setting.
There is no sound from the iPod.
ξξ
Make sure the iPod is securely connected.
ξξ
Adjust the VOLUME.
The iPod cannot be operated with this unit.
ξξ
Make sure the iPod is securely connected.
The iPod cannot be charged.
ξξ
Make sure the iPod is securely connected.
Preparing the remote
commander
Before using the remote commander for the first
time, remove the insulation film.
To know when to replace the
battery
With normal use, the battery (CR2025) should
last for about six months. When the remote
commander no longer operates the unit, replace
the battery with a new one.
CR2025
ξ
Ά
Notes
ξξ
Do not attempt to charge the battery.
ξξ
If you are not going to use the remote
commander for a long time, remove the battery
to avoid any damage that may be caused by
leakage and corrosion.
About the backup
battery
To keep accurate time, this unit contains a
CR2032 battery as a backup power source.
The battery keeps the clock and the alarm
operating in the event of a power interruption.
To know when to replace the
battery
When the battery becomes weak, β β appears in ξ
the display.
If a power interruption occurs while the battery is
weak, the current time and alarm settings will be
erased.
Replace the battery with a Sony CR2032 lithium
battery. Use of another battery may cause a fire or
explosion.
1 Remove the insulation film of the backup
battery at the bottom of the unit.
2 Extend the wire aerial fully.
3 Plug in the unit.
βAM 12:00β and βFRI 01-01-2010β flash for
about 2 seconds, then βScanning...β appears in
the display.
The unit will automatically scan and create a
list of receivable DAB broadcasts. The services
are stored in the list in alphabetical order.
When scanning is finished, the unit gets the time
from the DAB data of the first station received.
The current time appears in the display.
Notes
ξξ
If no broadcasts are found by the DAB scan,
βNO STATION FOUNDβ appears for about
2 seconds, then βAM 12:00β flashes in the
display. The clock cannot be set. In this case, set
the clock manually (see βSetting the clock
manuallyβ).
ξξ
If the system clock is already running (has been
set manually or synchronized from DAB
before), the system will not try to enter the
DAB function automatically when powering on
the unit.
ξξ
The clock time cannot be set via DAB data if it
is within an hour ahead or behind the start or
end of daylight saving time (summer time). In
this case, power on the unit at another time
setting, or set the clock manually (see βSetting
the clock manuallyβ).
When daylight saving time
(summer time) begins
This model automatically adjusts for daylight
saving time (summer time).
β β is displayed from the beginning of daylight
saving time (summer time) and disappears at the
end of the daylight saving time (summer time)
automatically.
The daylight saving time (summer time)
adjustment is based on GMT (Greenwich Mean
Time).
Tips
ξξ
Daylight saving time (summer time) begins at:
1:00 AM on the final Sunday of March.
ξξ
Standard time begins at: 2:00 AM on the final
Sunday of October.
To cancel Auto DST/summer time
adjustment during the daylight saving
time (summer time) period
The Auto DST/summer time adjustment can be
canceled.
Press and or to select the MENU SELECT ξ
ξ
²
βAuto DST,β and then press . Press ENTER SELECT
ξ
ξ
² or to select βOFF,β and then press ENTER
again. The β β mark disappears from the display.
The time returns to standard time.
To activate Auto DST/summer time
adjustment again
Press and or to select the MENU SELECT ξ
ξ
²
βAuto DST,β and then press . Press ENTER SELECT
ξ
ξ
² or to select βON,β and then press again. ENTER
The β β mark appears in the display. The time
returns to summer time.
Setting the clock manually
Do the following if DAB broadcast is not available
(depending on area). The time setting mode by
DAB becomes invalid.
1 Plug in the unit.
2 Press and or to select MENU SELECT ξ
ξ
²
βDate & Time,β and then press .ENTER
The year flashes in the display.
3 Press or to set the year, and SELECT ξ
ξ
²
then press .ENTER
4 Repeat step to set the month, day, hour 3
and minute.
The seconds start incrementing from zero.
2 Press TUNING + β TUNE + β or ( or on the
remote) to tune to the desired service or
station.
If a selected DAB service has finished
broadcasting, sound stops and βNO
SERVICEβ appears. In this case, press
TUNING + β TUNE + β or ( or on the
remote) to select another service.
3 Adjust volume using VOLUME + or β
( or on the remote).VOL + β
To turn off the radio, press .OFF
Note
MENU TUNING + β and or are not available when
βTuningβ¦β is displayed.
Note on FM usage
The frequency step is set to 0.05 MHz on FM.
Note on DAB usage
ξξ
βNO SERVICEβ appears when the selected
service cannot be received.
ξξ
DAB broadcasts with poor quality reception
may be selected when Auto scan is performed.
In this case, perform Manual tune, which may
improve reception.
About the SC (Secondary Component)
If the selected primary component has a
secondary component, βSCβ flashes in the display.
Press
TUNING +
or
β
(
TUNE +
or
β
on the
remote) to receive the desired secondary
component. βSCβ lights up while the secondary
component is being received.
Note
When the selected secondary component is
finished, the unit returns automatically to the
primary component.
Presetting your favourite
services or stations
You can preset up to 10 services in DAB (5 services
in DAB1, 5 services in DAB2) and 10 stations in
FM (5 stations in FM1, 5 stations in FM2).
Presetting services or stations
1 Follow to in βOperating the steps 1 2
radioβ and manually tune in to the
station you want to preset.
2 Press and hold the favourite STATION
SELECT PRESET 1 5 to button on the
unit.
βPRESETβ and the number flash for about
2 seconds in the display, then change to fully
lit. The service or station is stored.
Notes
ξξ
To preset another service or station, repeat
these steps.
ξξ
To change the preset service or station, tune in
to the desired service or station and repeat steps
1 2 and . The new service or station will replace
the previous service or station.
Tuning in to a preset service or station
1 Press DAB/FM repeatedly to select the
desired band.
2 Press one of the STATION SELECT
PRESET buttons on the unit where the
desired service or station is stored.
When the service or station is not registered,
βPRESET BLANKβ appears in the display.
The preset station can also be selected by
PRESET + β or on the remote.
3 Adjust the volume using VOLUME + or β
( or on the remote).VOL + β
Notes
ξξ
If there are no preset stations, βPRESET
BLANKβ will appear when you press PRESET +
or on the remote.β
ξξ
If there is only one preset station, its preset
number will flash each time you press PRESET
+ β or on the remote.
Auto preset tuning (FM only)
1 Press DAB/FM repeatedly to select the
FM band.
2 Press and or to select MENU SELECT ξ
ξ
²
βAuto Preset,β and then press . ENTER
3 Press or to select βYes,β and SELECT ξ
ξ
²
then press .ENTER
The unit automatically presets the available
channels for both FM1 and FM2 in order.
Tip
To stop auto preset tuning, press .OFF
Notes
ξξ
The clock setting is available in clock state only.
(When using radio, iPod or AUDIO IN, press
OFF to set the clock.)
ξξ
If you do not press any button for about
1 minute while setting the clock, the clock
setting will be canceled.
ξ A 100-year calendar (2010 - 2109) is installed in
the unit. When the date is set, the day of the
week is automatically displayed.
MON = Monday, TUE = Tuesday,
WED = Wednesday, THU = Thursday,
FRI = Friday, SAT = Saturday, SUN = Sunday
To change the time format
You can choose a time format between 12-hour
system (default) and 24-hour system.
1 Press
MENU
and
SELECT
or to select ξ
ξ
²
βTime Format,β and then press
ENTER
.
2 Press
SELECT
or to select the desired time ξ
ξ
²
format, and then press
ENTER
.
The time format toggles between 12-hour
system (βAM 12:00β = midnight) and 24-hour
system (β0:00β = midnight).
To change the date format
1 Press
MENU
and
SELECT
or to select ξ
ξ
²
βDate Format,β and then press
ENTER
.
2 Press
SELECT
or to select the desired ξ
ξ
²
date format, and then press
ENTER
.
To display the year and date when
using radio
Press SNOOZE/DATE/SLEEP OFF SNOOZE ( on
the remote).
After a few seconds, the display will change back
to the current service or station automatically.
Setting the brightness
of the display
Four levels of brightness are available by pressing
BRIGHTNESS.
Even if brightness level is set to OFF, it will
change to Middle while the alarm is sounding.
Improving the reception
DAB Band-III/FM
Extend the wire aerial fully to increase reception
sensitivity.
Keep the wire aerial away from AC power cord.
Do not bundle the wire aerial and AC power cord
together.
For DAB reception, press DISPLAY to show the
signal strength in order to rotate the aerial for
optimum reception.
Notes on radio reception
ξξ
Keep digital music players or mobile phones
away from the aerial, as this may lead to
reception interference.
ξξ
When you are listening to the radio with an
iPhone connected to the unit, interference with
radio reception may occur.
ξξ
When you are listening to the radio while
charging an iPod, interference with radio
reception may occur.
Tip
If an FM broadcast is noisy, press and MENU
SELECT or to select βMode,β and then press ξ
ξ
²
ENTER SELECT. Press or to select βMono,β and ξ
ξ
²
then press again. βMONOβ appears in the ENTER
display and the radio will play in monaural and
the sound will become clearer.
Operating the radio
The unit can receive DAB service and FM stations.
1 Press DAB/FM repeatedly to select the
desired band.
Each press changes the band as follows:
DAB1 DAB2
FM2 FM1
FM1 and FM2 or DAB1 and DAB2 are the
same frequency bands.
If a list of receivable DAB broadcasts has not
been created when you select DAB1 or DAB2,
βScanningβ¦β will appear in the display, and
the unit starts scanning automatically.
Β©2010 Sony Corporation Printed in China
XDR-DS12iP
Personal Audio
Docking System
Operating Instructions
Continued on the reverse side
No Power No Problem is a trademark of Sony Corporation.
ξξ
The connector of the unit is exclusively for use
with an iPod. If you use a device that does not
match the connector, connect it to the AUDIO
IN jack of this unit with the supplied audio
connecting cable.
ξξ
Sony cannot accept responsibility in the event
that data recorded on an iPod is lost or damaged
when using an iPod connected to this unit.
ξξ
For details of environmental conditions for
operating your iPod, check the website of Apple
Inc.
1 Attach the adapter for your iPod/iPhone,
and then insert your iPod/iPhone into
the connector of the unit (see Fig. ).ξ
2 Press iPod & iPhone ξ.
The iPod begins to play automatically.
You can operate the connected iPod by this
unit or the buttons on iPod.
3 Adjust the volume using VOLUME + β or
( or on the remote).VOL + β
To Press
Turn off the iPod OFF, or press and
hold iPod &
iPhone ξ
Pause playback iPod & iPhone
ξ To resume
play, press it again.
Go to the next track ξ (forward)
Go back to the previous
track ξ
(backward)*
Locate a point while
listening to the sound ξ (forward) or
ξ
(backward)
while playing and
hold it until you
find the point.
Locate a point while
observing the display ξ (forward) or
ξ
(backward)
in pause and hold
it until you find
the point.
Go back to the previous
menu
MENU
Select a menu item or a
track for playback ξ
¬ ξ (up)/ (down)**
Execute the selected menu
or begin playback
ENTER
Change to the repeat mode
MODE**
Change to the shuffle mode
Press and hold
MODE**
* During playback, this operation goes back to
the beginning of the current track. To go back
to the previous track, press twice.
** These operations are available only when using
the supplied remote commander.
Notes
ξξ
When placing or removing the iPod, hold the
iPod at the same angle as that of the connector
on this unit, and do not twist or bend the iPod
as connector damage may result.
ξξ
Do not carry the unit with an iPod set on the
connector. Doing so may cause a malfunction.
ξξ
When placing or removing the iPod, hold the
Docking Tray securely with one hand and take
care not to press the controls of the iPod by
mistake.
ξξ
Before disconnecting the iPod, pause playback.
To use the unit as a battery charger
You can use the unit as a battery charger.
Charging begins when the iPod is connected to
the unit.
Charging status appears in the display of iPod. For
details, see the userβs guide of your iPod.
On copyrights
iPhone, iPod, iPod classic, iPod nano, and iPod
touch are trademarks of Apple Inc., registered in
the U.S. and other countries.
βMade for iPod,β and βMade for iPhoneβ mean
that an electronic accessory has been designed to
connect specifically to iPod or iPhone,
respectively, and has been certified by the
developer to meet Apple performance standards.
Apple is not responsible for the operation of this
device or its compliance with safety and
regulatory standards. Please note that the use of
this accessory with iPod or iPhone may affect
wireless performance.
Setting the alarm
This unit is equipped with 3 alarm modesβiPod,
radio and buzzer. Before setting the alarm, make
sure to set the clock (see βSetting the clock for the
first timeβ).
To set the alarm
1 Press and hold or . ALARM SET A B
βAlarmβA Settingβ or βAlarmβB Settingβ
appears and the hour flashes in the display.
2 Press ALARM TIME SET + β or
repeatedly until the desired hour appears.
To cycle the hour rapidly, press and hold
ALARM TIME SET + β or .
3 Press or . ALARM SET A B
The minute flashes.
4 Repeat step to set the minute.2
5 Press or . ALARM SET A B
The days of the week flash.
6 Repeat step to set the days of the week.2
You can select the day from the following
three options:
EVERYDAY: MON TUE WED THU FRI SAT
SUN
WEEKDAY: MON TUE WED THU FRI
WEEKEND: SAT SUN
7 Press or . ALARM SET A B
The alarm mode setting is entered.
8 Press ALARM TIME SET + β or
repeatedly until the desired alarm mode
flashes.
You can choose one of 8 settings: βiPod,β
βDAB1,β βDAB2,β βDAB--,β βFM1,β βFM2,β
βFM--β or βBUZZER.β
βDAB--β and βFM--β are the last station
received.
Set the alarm mode as follows:
β iPod: see β Setting the iPod alarm.βξ
β DAB1, DAB2, DAB--, FM1, FM2 or FM--:
see β Setting the radio alarm.βξ
β BUZZER: see β Setting the buzzer alarm.βξ
ξ
Setting the alarm for iPod
1
Perform steps to in βTo set the alarm.β1 8
2 Press or to select ALARM SET A B
alarm mode for βiPod.β
βALARM VOLUME:β and volume number
flash in the display.
3 Press ALARM TIME SET + β or to adjust
the volume.
4 Press or . ALARM SET A B
The setting is entered.
5 If βAβ or βBβ does not appear in the
display, press or ALARM SET A B
again.
The iPod will sound at the set time.
When using an iPod touch/iPhone
ξξ
To wake up to music stored in an iPod touch/
iPhone, connect the iPod touch/iPhone to the
unit first, follow the steps above to set alarm
time, and then select the music function.
ξξ
Even if the alarm setting for iPod is complete, if
you turn the iPod touch/iPhone power off
before inserting the iPod touch/iPhone into the
unit, the alarm for iPod will not work.
ξ Setting the radio alarm
1
Perform steps to in βTo set the alarm.β1 8
2 Press or to select ALARM SET A B
radio band (βDAB1,β βDAB2,β βDAB--,β
βFM1,β βFM2β or βFM--β).
Preset number
The preset number flashes in the display.
When you select βDAB--β or βFM--,β then
jump to the step .5
3 Press ALARM TIME SET + β or to select
the desired preset number corresponding
to the band.
Press DISPLAY to confirm the preset details:
Frequency for FM and component label for
DAB.
Tips
ξξ
If the selected preset number is not set,
βPRESET BLANKβ flashes two times, and
then βALARM VOLUME:β and volume
number flash in the display. Then jump to
the step .5
ξξ
If there is no last station, βNO LAST
STATIONβ flashes two times, and then
βALARM VOLUME:β and volume number
flash in the display. Then jump to the step .5
4 Press or . ALARM SET A B
βALARM VOLUME:β and volume number
flash in the display.
5 Press ALARM TIME SET + β or to adjust
the volume.
6 Press or . ALARM SET A B
The setting is entered.
7 If βAβ or βBβ does not appear in the
display, press or ALARM SET A B
again.
The radio will turn on at the set time.
Note
If the selected preset number is not set, or there is
no last station, the alarm sound will be buzzer
when alarm time is met. If you want to change the
buzzer alarm, set preset station or tune radio
station (see βOperating the radioβ).
ξ Setting the buzzer alarm
1
Perform steps to in βTo set the alarm.β1 8
2 Press or to select ALARM SET A B
βBUZZERβ alarm mode.
The setting is entered.
3 If βAβ or βBβ does not appear in the
display, press or ALARM SET A B
again.
The buzzer will sound at the set time.
Note
The volume cannot be set for the buzzer alarm.
To confirm an alarm time setting
Press ALARM TIME SET + β or . The setting will
be displayed for about 4 seconds.
To change an alarm setting
Press and hold ALARM TIME SET + for at least 2
seconds to move the alarm time forwards. Press
and hold ALARM TIME SET β for at least 2
seconds to move the alarm time back.
When you release the button, the changed time
will flash for about 2 seconds. To change the
alarm time again, press ALARM TIME SET + β or
within these 2 seconds, otherwise the setting
change will be fixed as displayed.
To doze for a few more minutes
Press SNOOZE/DATE/SLEEP OFF SNOOZE ( on
the remote).
The sound turns off but will automatically come
on again after about 10 minutes.
You can change the snooze time by pressing
SNOOZE/DATE/SLEEP OFF SNOOZE ( on the
remote) repeatedly within 4 seconds.
The maximum length of the snooze time is
60 minutes.
To stop the snooze timer, press OFF/ALARM
RESET OFF( on the remote).
To stop the alarm
Press ( on the remote) OFF/ALARM RESET OFF
to turn off the alarm.
The alarm will sound again at the same time the
next day.
To deactivate the alarm
Press or to turn off the ALARM ON/OFF A B
alarm A or B indicator from the display.
To activate the alarm
Press or to turn on the ALARM ON/OFF A B
alarm A or B indicator in the display.
Notes
ξξ
With the alarm mode is set to iPod, when the
alarm time met, if iPod is not attached to the
unit, the alarm sound will be the buzzer.
ξξ
The alarm function works as usual on the first
and last day of daylight saving time (summer
time). As a result, if the Auto DST/summer time
adjustment is set and the alarm is set at a time
skipped when the daylight saving time begins,
the alarm sounds; if the alarm is set to a time
that overlaps when daylight saving time ends,
the alarm will sound twice.
ξξ
If the same alarm time is set for both alarm A
and B, alarm A takes priority.
ξξ
If there is no operation while the alarm is
occurring, the alarm will stop after about
60 minutes.
Note on the alarm in the event of a power
interruption
In the event of a power interruption, the buzzer
alarm will last about 5 minutes if the battery is not
weak.
However, certain functions will be affected as
follows:
ξξ
The backlight will not light up.
ξξ
If the alarm mode is set to iPod or radio, it will
change to buzzer automatically.
ξξ
If is not pressed, the alarm OFF/ALARM RESET
will sound for about 5 minutes.
ξξ
If β β appears in the display, the alarm will not ξ
sound in the event of a power interruption.
Replace the battery if β β appears.ξ
ξξ
The snooze function cannot be set during a
power interruption. If the snooze function has
already been set and a power interruption
occurs, the snooze function will not work.
ξξ
During a power interruption, each alarm will
sound at the set time only once.
Setting the sleep timer
You can fall asleep to music, etc., using the sleep
timer. The unit stops playback or radio
automatically after a preset duration.
1 Press while the unit is turned on. SLEEP
βSLEEP:β and the sleep time flash in the
display.
2 Press to set the sleep timer SLEEP
duration.
Each time you press , the duration (in SLEEP
minutes) changes as follows:
90 60 30 15
OFF
The display returns to clock mode for about
4 seconds after you have finished the duration
setting and released , and then the sleep SLEEP
timer starts.
The unit plays for the duration you set, and
then stops.
To turn off the unit before the preset
time
Press SNOOZE/DATE/SLEEP OFF SNOOZE ( on
the remote) or ( on the OFF/ALARM RESET OFF
remote).
To change the sleep timer setting
You can press repeatedly to select the SLEEP
desired sleep timer setting even after the sleep
timer has been activated.
To deactivate the sleep timer
Press repeatedly to set the sleep timer to SLEEP
βOFFβ in step .2
Other useful functions
for DAB
Changing the display
To change the display mode, press DISPLAY
during DAB reception. The selected display mode
remains even if you turn the unit off and on
again, or change the band.
The display can be up to 16 characters long. A
dynamic label can be up to 128 characters in
length.
Each time you press DISPLAY, the display
changes as follows*:
Function and Preset number
Dynamic
PTY (Program Type)
Ensemble
Channel/Frequency/Signal Strength
Component Label
* When holding down DISPLAY for about
2 seconds or more, the display changes as
follows:
Broadcasting/Bit rate/Stereo, Mono
DAB broadcasting: MP2
DAB+ broadcasting: AAC
The display will change to the previous display for
about 4 seconds automatically if no operation is
performed.
Notes
ξξ
If there is no component label, βNO COMP
LABELβ will be displayed.
ξξ
If there is no ensemble label, βNO ENS LABELβ
will be displayed.
ξξ
If there is no program type, βNO PROGS
TYPEβ will be displayed.
ξξ
If there is no dynamic label, the lower line of
the display is blank.
ξξ
Depending on the broadcasting station, the
characters in dynamic labels may not be
displayed properly.
Manual tune
This function allows you to tune and add the
various DAB Band-III channels to your station
list.
This function can be used to assist the positioning
of the aerial or the unit to obtain the optimum
reception for a specific channel / frequency.
1 Press DAB/FM repeatedly to select the
DAB band.
2 Press and or to select MENU SELECT ξ
ξ
²
βManual Tune,β and then press .ENTER
3 Press or to select the desired SELECT ξ
ξ
²
DAB channel, and then press .ENTER
The unit searches stations and lists up all the
stations belonging to this channel.
When pressing DISPLAY, the signal strength
bars will go left and right showing the
changing signal strength as you adjust the
reception.
4 Press or to select the desired SELECT ξ
ξ
²
service, then press . ENTER
Note
If the desired channel selected in step cannot be 3
received, press to select another channel.MENU
DRC Value (DYNAMIC RANGE CONTROL)
DRC can make quieter sounds easier to hear
when the unit is used in a noisy environment.
For DAB broadcasts with dynamic range
compression, you can adjust the dynamic range
by this unit.
1 Press DAB/FM repeatedly to select the
DAB band.
2 Press and or to select MENU SELECT ξ
ξ
²
βDRC Value,β and then press .ENTER
3 Press or to select the DRC SELECT ξ
ξ
²
level.
The DRC level changes as follows:
0 ΒΉ/β 1(default)
2
4 Press .ENTER
Notes
ξξ
DRC is effective only in dynamic range
compression broadcasts.
ξξ
When you adjust the DRC level, volume can be
heard more loudly.
Autoscan
These functions allow you to automatically scan
and create a list of receivable DAB broadcasts.
1 Press DAB/FM repeatedly to select the
DAB band.
2 Press and or to select MENU SELECT ξ
ξ
²
βAuto Scan,β and then press .ENTER
3 Press or to select βYes,β and SELECT ξ
ξ
²
then press .ENTER
βScanning...β appears in the display.
Autoscan takes about 30 - 90 seconds. When
finished, the unit creates a list in alphabetical
order.
Note
When Autoscan is performed, the existing list will
be updated and the preset services will be cleared.
In this case, preset your favourite services again.
Trim stations
You can delete the stations that are not currently
being received.
1 Press DAB/FM repeatedly to select the
DAB band.
2 Press and or to select MENU SELECT ξ
ξ
²
βPrune,β and then press .ENTER
When finished, βFINISH!β appears for about
1 second, then changes to the current station
automatically.
Confirm service list information
1 Press DAB/FM repeatedly to select the DAB
band.
2 Press MENU and or to select SELECT ξ
ξ
²
βServlist Info,β and then press .ENTER
3 Press or to select βEnsβ or SELECT ξ
ξ
²
βServβ or βCompβ to confirm the amount
of the ensemble, service or component.
Sync time now
You can synchronize time from DAB broadcasts.
1 Press DAB/FM repeatedly to select the
DAB band.
2 Press and or to select MENU SELECT ξ
ξ
²
βSync Time Now,β and then press .ENTER
When finished, βFINISH!β appears for about
2 seconds.
Note
If no DAB broadcast can be received, βDAB TIME
INVALIDβ appears for about 2 seconds in the
display. In this case, adjust the positioning of the
aerial or the unit to obtain the optimum
reception.
Select Station
Another service can be selected while listening to
a broadcast.
1 Press and or to select MENU SELECT ξ
ξ
²
βSelect Station,β and then press .ENTER
2 Press or to select a desired SELECT ξ
ξ
²
service, and then press .ENTER
PTY (Programme Type)
This function indicates services in programme
type, such as NEWS, SPORTS of the PTY list,
transmitted in a DAB broadcast.
If the received service or station does not transmit
the programme type, βNO PTY Dataβ appears.
Programme type Display
Undefined None
News News
Current Affairs Current Affairs
Information Information
Sport Sport
Education Education
Drama Drama
Culture Cultures
Science Science
Varied
Varied Speech
Pop Music
Pop Music
Rock Music Rock Music
Easy Listening Music Easy Listening
Light Classical Light Classics M
Serious Classical Serious Classics
Other Music Other Music
Weather Weather & Metr
Finance Finance
Childrenβs programmes Childrenβs Progs
Social Affairs Social Affairs
Religion Religion
Phone In Phone In
Travel Travel & Touring
Leisure Leisure & Hobby
Jazz Music Jazz Music
Country Music Country Music
Nation Music Nation Music
Oldies Music Oldies Music
Folk Music Folk Music
Documentary Documentary
Other useful functions
To obtain the MEGA Xpand effect
Press . βMEGA Xpandβ appears in MEGA Xpand
the display. The effect expands the sound field. To
return to normal sound, press the button again.
To reinforce the bass sound
Press . βMEGA BASSβ appears in the MEGA BASS
display. The effect expands the bass content of the
sound. To return to normal sound, press the
button again.
The and VOL + buttons have a tactile dot.ξ
AC power cord
The STATION SELECT PRESET 3, VOLUME + and iPod & iPhone buttons have a ξ
tactile dot.
wire aerial
Connecting external
equipment
To listen to sound
1 Connect the jack on the back AUDIO IN
of the unit to the line out jack or
headphone jack of the external
equipment using the supplied audio
connecting cable.
Audio connecting cable
(supplied)
To external
equipment
2 Press AUDIO IN to display βAUDIO IN.β
3 Play the equipment connected to the
AUDIO IN jack.
4
Adjust the volume using VOLUME + β or
( or on the remote).VOL + β
To return to the radio
Press DAB/FM.
To return to the iPod
Press iPod & iPhone ξ.
To stop listening
Press and stop playback on the connected OFF
unit.
Notes
ξξ
The cannot be operated while Audio in MENU
is used.
ξξ
Refer also to the connected equipmentβs manual.
ξξ
The supplied audio connecting cable may not
be used with some external equipment. In this
case, use a cord suitable for the external
equipment you are using.
ξξ
When you listen to the radio with external
equipment connected, turn off the connected
equipment to prevent noise. If noise occurs,
even when the equipment is turned off,
disconnect and place the external equipment
away from the unit.
Scan Tuning (FM only)
The unit automatically scans FM stations.
1 Press DAB/FM repeatedly to select the
FM band.
2 Press and hold or (TUNING + β TUNE +
or on the remote).β
+ : scans upward through the frequency bands.
β
:
scans downwards through the frequency
bands.
Scanning starts from the currently-tuned
frequency. When a station is received,
scanning stops.
3 Adjust the volume using VOLUME + β or
( or on the remote).VOL + β
Operating an iPod
You can enjoy audio from iPod by connecting to
this unit. To use an iPod, refer to the userβs guide
of your iPod.
If you are using an iPhone 4S, iPhone 4, iPhone
3GS, iPhone 3G or iPhone, attach the supplied
universal dock adapter for iPhone 4S, iPhone 4,
iPhone 3GS, iPhone 3G or iPhone before
connecting.
The adapter number, , or , is shown on ξ ξ£ ξ§
the underside of the supplied universal dock
adapters. is for the iPhone, is for the iPhone ξ ξ£
3GS & iPhone 3G and is for the iPhone 4S & ξ§
iPhone 4. Check the adapter number before use.
ξ ξ£
Universal Dock Adapter
ξ§
Notes
ξξ
When inserting an iPod into the unit, be sure to
use the universal dock adapter supplied with your
iPod or commercially available from Apple Inc.
ξ
Produktspezifikationen
Marke: | Sony |
Kategorie: | Receiver |
Modell: | XDR-DS12iP |
Brauchst du Hilfe?
Wenn Sie Hilfe mit Sony XDR-DS12iP benΓΆtigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten
Bedienungsanleitung Receiver Sony
3 September 2024
2 September 2024
31 August 2024
12 August 2024
3 August 2024
24 Juli 2024
16 Juli 2024
4 Juli 2024
8 Oktober 2022
Bedienungsanleitung Receiver
- Receiver Asus
- Receiver Hama
- Receiver Audio-Technica
- Receiver Logitech
- Receiver Manhattan
- Receiver Nedis
- Receiver Philips
- Receiver Sandberg
- Receiver Roland
- Receiver MX Onda
- Receiver Bosch
- Receiver Vox
- Receiver TechniSat
- Receiver Yamaha
- Receiver Velleman
- Receiver CSL
- Receiver Alecto
- Receiver Denver
- Receiver EMOS
- Receiver KΓΆnig
- Receiver MarQuant
- Receiver Renkforce
- Receiver Bush
- Receiver Thomson
- Receiver Blaupunkt
- Receiver Kenwood
- Receiver Sharp
- Receiver Hilti
- Receiver Pyle
- Receiver Golden Age Project
- Receiver Aiwa
- Receiver AKG
- Receiver Auna
- Receiver Bose
- Receiver Bowers And Wilkins
- Receiver Caliber
- Receiver Denon
- Receiver Pioneer
- Receiver JBL
- Receiver JVC
- Receiver Klipsch
- Receiver Motorola
- Receiver Onkyo
- Receiver Sennheiser
- Receiver Shure
- Receiver Technics
- Receiver Vivanco
- Receiver Hifonics
- Receiver Megasat
- Receiver Smartwares
- Receiver Akai
- Receiver Dual
- Receiver Ferguson
- Receiver Strong
- Receiver Tascam
- Receiver Zoom
- Receiver Garmin
- Receiver Nexa
- Receiver Goobay
- Receiver Lindy
- Receiver Fenton
- Receiver TOA
- Receiver Rotel
- Receiver Musway
- Receiver Tripp Lite
- Receiver Audio Pro
- Receiver Cabasse
- Receiver Harman Kardon
- Receiver Magnat
- Receiver Marmitek
- Receiver Marshall
- Receiver Naim
- Receiver Power Dynamics
- Receiver Samson
- Receiver Scosche
- Receiver Skytec
- Receiver Vonyx
- Receiver Peavey
- Receiver Marshall Electronics
- Receiver Sagem
- Receiver Simrad
- Receiver AVM
- Receiver Xoro
- Receiver Karma
- Receiver Reely
- Receiver Edision
- Receiver GigaBlue
- Receiver Humax
- Receiver Kathrein
- Receiver Metronic
- Receiver Xtrend
- Receiver Icom
- Receiver Alpine
- Receiver Rupert Neve Designs
- Receiver NAD
- Receiver Fender
- Receiver Renegade
- Receiver Ebode
- Receiver Vision
- Receiver Behringer
- Receiver Mackie
- Receiver Omnitronic
- Receiver MB Quart
- Receiver Marantz
- Receiver Monoprice
- Receiver Arcam
- Receiver Cambridge
- Receiver Crown
- Receiver Dynacord
- Receiver Ecler
- Receiver Luxman
- Receiver Monacor
- Receiver TEAC
- Receiver Thorens
- Receiver Crunch
- Receiver Chamberlain
- Receiver JUNG
- Receiver Aplic
- Receiver InLine
- Receiver Sangean
- Receiver ClassΓ©
- Receiver Optex
- Receiver Sherwood
- Receiver Jamo
- Receiver AXTON
- Receiver Clarion
- Receiver Mac Audio
- Receiver Kogan
- Receiver Humantechnik
- Receiver Skytronic
- Receiver Yaesu
- Receiver Audizio
- Receiver ESX
- Receiver Reloop
- Receiver Pinnacle
- Receiver Block
- Receiver Rega
- Receiver SYNQ
- Receiver Insignia
- Receiver DataVideo
- Receiver RCF
- Receiver Electro-Voice
- Receiver Cyrus
- Receiver Scansonic
- Receiver Sogo
- Receiver Delta Dore
- Receiver Salus
- Receiver Yorkville
- Receiver Elektrobock
- Receiver FiiO
- Receiver Boss
- Receiver IFM
- Receiver American Audio
- Receiver Anthem
- Receiver Roksan
- Receiver Engel Axil
- Receiver Alto
- Receiver Kopul
- Receiver Chord
- Receiver Kramer
- Receiver Hertz
- Receiver Pro-Ject
- Receiver Aeon Labs
- Receiver Vaddio
- Receiver Galaxy Audio
- Receiver HQ Power
- Receiver Ibiza Sound
- Receiver Kicker
- Receiver Warm Audio
- Receiver Polk
- Receiver Line 6
- Receiver Bogen
- Receiver DBX
- Receiver McIntosh
- Receiver Sonance
- Receiver Jensen
- Receiver JL Audio
- Receiver Pyle Pro
- Receiver PreSonus
- Receiver Qtx
- Receiver Hartke
- Receiver ART
- Receiver Deaf Bonce
- Receiver Fredenstein
- Receiver LD Systems
- Receiver RDL
- Receiver Audiolab
- Receiver Summit Audio
- Receiver Black Lion Audio
- Receiver Bluesound
- Receiver GlobalSat
- Receiver Chandler
- Receiver DAP
- Receiver DAP Audio
- Receiver Denson
- Receiver DLS
- Receiver Focal
- Receiver Focusrite
- Receiver Formuler
- Receiver Fusion
- Receiver Graupner
- Receiver Ground Zero
- Receiver Helix
- Receiver Homecast
- Receiver Infinity
- Receiver JB Systems
- Receiver Koda
- Receiver Lanzar
- Receiver Legamaster
- Receiver Mercury
- Receiver Monitor Audio
- Receiver Mtx Audio
- Receiver Phoenix Gold
- Receiver REL Acoustics
- Receiver Selfsat
- Receiver Soundstream
- Receiver Steren
- Receiver Sunstech
- Receiver Terratec
- Receiver AMX
- Receiver Triax
- Receiver Wharfedale
- Receiver Phonic
- Receiver Adastra
- Receiver Siig
- Receiver Amiko
- Receiver Mooer
- Receiver AudioControl
- Receiver StarTech.com
- Receiver Blackstar
- Receiver Smart-AVI
- Receiver QSC
- Receiver Dahua Technology
- Receiver Proel
- Receiver Niles
- Receiver Martin Logan
- Receiver Sound Devices
- Receiver Speco Technologies
- Receiver IFi Audio
- Receiver Gefen
- Receiver Polsen
- Receiver Russound
- Receiver Vocopro
- Receiver SRS
- Receiver Astell&Kern
- Receiver IMG Stage Line
- Receiver Inovonics
- Receiver Mosconi
- Receiver Atlas Sound
- Receiver CYP
- Receiver Amplicom
- Receiver Ampeg
- Receiver Avalon
- Receiver Bang Olufsen
- Receiver Lectrosonics
- Receiver ATen
- Receiver Eventide
- Receiver Laney
- Receiver SVS
- Receiver Citronic
- Receiver Crest Audio
- Receiver Lab Gruppen
- Receiver SPL
- Receiver Parasound
- Receiver MEE Audio
- Receiver Wet Sounds
- Receiver Pyramid
- Receiver Stewart
- Receiver Black Hydra
- Receiver Linn
- Receiver Roswell
- Receiver Music Hall
- Receiver Audac
- Receiver OSD Audio
- Receiver Match
- Receiver Neets
- Receiver EA
- Receiver BZBGear
- Receiver Crestron
- Receiver HiFi ROSE
- Receiver Accell
- Receiver Ibanez
- Receiver Antelope Audio
- Receiver Pharos
- Receiver Kemo
- Receiver Avantree
- Receiver PSB
- Receiver Extron
- Receiver Comtek
- Receiver Ashdown Engineering
- Receiver Ram Audio
- Receiver Esoteric
- Receiver Xantech
- Receiver Artsound
- Receiver Rolls
- Receiver Sonifex
- Receiver Advance Acoustic
- Receiver Wireless Solution
- Receiver Manley
- Receiver Klark Teknik
- Receiver AVMATRIX
- Receiver Mark Levinson
- Receiver Ocean Matrix
- Receiver Markbass
- Receiver AmpliVox
- Receiver LEA
- Receiver Memphis Audio
- Receiver Televes
- Receiver Aquatic AV
- Receiver Ashly
- Receiver Fishman
- Receiver Integra
- Receiver Blustream
- Receiver CyberData Systems
- Receiver JETI
- Receiver SureCall
- Receiver ANKARO
- Receiver NUVO
- Receiver Audiofrog
- Receiver MuxLab
- Receiver Hegel
- Receiver Triangle
- Receiver Whirlwind
- Receiver Hughes & Kettner
- Receiver Palsonic
- Receiver Musical Fidelity
- Receiver A-NeuVideo
- Receiver Crest
- Receiver Primare
- Receiver C2G
- Receiver Fosi Audio
- Receiver S.M.S.L
- Receiver Advance
- Receiver AEA
- Receiver TechLogix Networx
- Receiver CE Labs
- Receiver Audiotec Fischer
- Receiver Shinybow
- Receiver Shanling
- Receiver Fontastic
- Receiver NuPrime
- Receiver Valcom
- Receiver Intelix
- Receiver Madison
- Receiver Topp Pro
- Receiver Whistler
- Receiver Powersoft
- Receiver LinksPoint
- Receiver Modelcraft
- Receiver Simaudio
- Receiver FSR
- Receiver Edwards Signaling
- Receiver IOTAVX
- Receiver Inter-M
- Receiver Soundtrack
- Receiver Canor
- Receiver Unison Research
- Receiver Clare Controls
- Receiver Loxjie
- Receiver Cayin
- Receiver Technical Pro
- Receiver VMV
- Receiver Bellari
- Receiver Comprehensive
- Receiver PureLink
- Receiver FoneStar
- Receiver Glemm
Neueste Bedienungsanleitung fΓΌr -Kategorien-
16 September 2024
16 September 2024
16 September 2024
15 September 2024
15 September 2024
15 September 2024
15 September 2024
15 September 2024
15 September 2024
14 September 2024