Sony ICF-DS11iP Bedienungsanleitung

Sony Ipod Audio ICF-DS11iP

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Sony ICF-DS11iP (4 Seiten) in der Kategorie Ipod Audio. Dieser Bedienungsanleitung war für 13 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Download PDF

Seite 1/4

WARNING

To reduce the risk of fire or electric shock, do

not expose this apparatus to rain or

moisture.

To reduce the risk of fire, do not cover the

ventilation of the apparatus with newspapers,

tablecloths, curtains, etc. And do not place lighted

candles on the apparatus.

To reduce the risk of fire or electric shock, do not

expose this apparatus to dripping or splashing,

and do not place objects filled with liquids, such

as vases, on the apparatus.

Do not install the appliance in a confined space,

such as a bookcase or built-in cabinet.

Do not expose the batteries (battery pack or

batteries installed) to excessive heat such as

sunshine, fire or the like for a long time.

As the main plug is used to disconnect the unit

from the mains, connect the unit to an easily

accessible AC outlet. Should you notice an

abnormality in the unit, disconnect the main plug

from the AC outlet immediately.

The unit is not disconnected from the AC power

source (mains) as long as it is connected to the

wall outlet, even if the unit itself has been turned

off.

The nameplate and important information

concerning safety are located on the bottom

exterior.

CAUTION

Danger of explosion if battery is incorrectly

replaced. Replace only with the same type.

Notice for customers: the following

information is only applicable to equipment

sold in countries applying EU directives

The manufacturer of this product is Sony

Corporation, 1-7-1 Konan Minato-ku Tokyo,

108-0075 Japan. The Authorized Representative

for EMC and product safety is Sony Deutschland

GmbH, Hedelfinger Strasse 61, 70327 Stuttgart,

Germany. For any service or guarantee matters

please refer to the addresses given in separate

service or guarantee documents.

Precautions



Operate the unit on the power source specified

in “Specifications.”



Since a strong magnet is used for the speaker,

keep personal credit cards using magnetic coding

or spring-wound watches away from the unit to

prevent possible damage from the magnet.



Do not leave the unit in a location near a heat

source such as a radiator or airduct, or in a

place subject to direct sunlight, excessive dust,

mechanical vibration, or shock.



Allow adequate air circulation to prevent internal

heat build-up. Do not place the unit on a surface

(a rug, a blanket, etc.) or near materials (a

curtain) which might block the ventilation holes.



Should any solid object or liquid fall into the unit,

unplug the unit and have it checked by qualified

personnel before operating it any further.



To clean the casing, use a soft cloth dampened

with a mild detergent solution.



Never touch the wire of the external FM aerial

during a thunderstorm. Furthermore,

immediately disconnect the AC power cord

from the radio.

NOTES ON LITHIUM BATTERY



Wipe the battery with a dry cloth to assure a

good contact.



Be sure to observe the correct polarity when

installing the battery.



Do not hold the battery with metallic tweezers,

otherwise a short-circuit may occur.

Disposal of Old Electrical &

Electronic Equipment (Applicable

in the European Union and other

European countries with separate

collection systems)

This symbol on the product or on its packaging

indicates that this product shall not be treated as

household waste. Instead it shall be handed over

to the applicable collection point for the recycling

of electrical and electronic equipment. By

ensuring this product is disposed of correctly, you

will help prevent potential negative consequences

for the environment and human health, which

could otherwise be caused by inappropriate waste

handling of this product. The recycling of

materials will help to conserve natural resources.

For more detailed information about recycling of

this product, please contact your local Civic

Office, your household waste disposal service or

the shop where you purchased the product.

Applicable accessory: Remote Commander.

Disposal of waste batteries

(applicable in the European

Union and other European

countries with separate

collection systems)

This symbol on the battery or on the packaging

indicates that the battery provided with this

product shall not be treated as household waste.

On certain batteries this symbol might be used in

combination with a chemical symbol. The

chemical symbols for mercury (Hg) or lead (Pb)

are added if the battery contains more than

0.0005% mercury or 0.004% lead.

By ensuring these batteries are disposed of

correctly, you will help prevent potentially

negative consequences for the environment and

human health which could otherwise be caused

by inappropriate waste handling of the battery.

The recycling of the materials will help to

conserve natural resources.

In case of products that for safety, performance or

data integrity reasons require a permanent

connection with an incorporated battery, this

battery should be replaced by qualified service

staff only.

To ensure that the battery will be treated properly,

hand over the product at end-of-life to the

applicable collection point for the recycling of

electrical and electronic equipment.

For all other batteries, please view the section on

how to remove the battery from the product

safely. Hand the battery over to the applicable

collection point for the recycling of waste

batteries.

For more detailed information about recycling of

this product or battery, please contact your local

Civic Office, your household waste disposal

service or the shop where you purchased the

product.

If you have any questions or problems concerning

your unit, please consult your nearest Sony dealer.

Features



Compatible with iPod/iPhone



Wake or Sleep to iPod/Radio/Buzzer



Easy to set A-B alarm



2-5-7day alarm



LCD Brightness control



MEGA BASS



MEGA Xpand



Wireless Remote Commander

Specifications

Time display

24-hour system

Section for iPod

DC out: 5V

MAX: 500mA

Radio section

Frequency range

Band Frequency Channel

step

FM 87.5 MHz – 108 MHz 0.05 MHz

AM 531 kHz – 1 602 kHz 9 kHz

General

Speaker

Approx. 5.7 cm (2 1/4 inches) dia. 6 Ω

Input

AUDIO IN jack (ø 3.5 mm stereo minijack)

Power output

3.5 W + 3.5 W (at 10% harmonic distortion)

Power requirements

230 V AC, 50 Hz

For clock back up: 3V DC, CR2032 battery (1)

Dimensions

Approx. 290.5 mm × 152.0 mm × 139.5 mm (w/h/d)

(11 3/8 inches × 5 15/16 inches × 5 1/2 inches)

including projecting parts and controls

Mass

Approx. 2.0 kg (4 lb 7 oz) including power supply

unit

Supplied accessories

Remote commander (1)

AM loop aerial (1)

Audio connecting cable (1)

Universal Dock Adapter for iPhone (1)

Universal Dock Adapter for iPhone 3G & iPhone

3GS (1)

Universal Dock Adapter for iPhone 4 (1)

Design and specifications are subject to change

without notice.

Compatible iPod/iPhone

models

Compatible iPod/iPhone models are as follows.

Update your iPod/iPhone to use the latest

software before you use it.

iPod touch

1st generation

iPod nano

3rd generation

(video)

iPod

5th generation

(video)

iPod classic

iPhone 3GS

iPod touch

3rd generation

iPod nano

5th generation

(video camera)

iPod nano

2nd generation

(aluminum)

iPod

4th generation

(color display)

iPod mini

iPhone 3G

iPod touch

2nd generation

iPod nano

4th generation

(video)

iPod nano

1st generation

iPod

4th generation

iPhone 4

iPhone

Notes



In these Operating Instructions, “iPod” is used

as a general reference to functions of iPod on an

iPod or iPhone, unless otherwise specified by

the text or illustrations.



The connector of the unit is for sole use with an

iPod. If you use devices that do not match with

the connector, connect to the AUDIO IN jack of

this unit with the supplied audio connecting

cable.



Sony cannot accept responsibility in the event

that data recorded to an iPod is lost or damaged

when using an iPod connected to this unit.

Troubleshooting

Should any problem persist after you have made

the following checks, consult your nearest Sony

dealer.

The clock flashes “0:00” due to a power

interruption.



The battery is low. Replace the battery. Remove

the old battery and install a new one.

The alarm of radio, iPod or buzzer does not

sound at the preset alarm time.



Check that alarm “A” or alarm “B” is properly

displayed.

The alarm of radio or iPod is activated but no

sound comes on at the preset alarm time.



Check the alarm volume setting.

There is no sound from the iPod.



Make sure the iPod is securely connected.



Adjust the VOLUME.

The iPod cannot be operated with this unit.



Make sure the iPod is securely connected.

The iPod cannot be charged.



Make sure the iPod is securely connected.

4-150-697- (1)42 Notes



Do not attempt to charge the battery.



If you are not going to use the remote

commander for a long time, remove the battery

to avoid any damage that may be caused by

leakage and corrosion.

About the backup

battery

To keep accurate time, this unit contains a

CR2032 battery as a backup power source.

The battery keeps the clock and the alarm

operating in the event of a power interruption.

Note for customers in Europe

The clock is preset at the factory, and its memory

is powered by the preinstalled Sony CR2032

battery. If the “0:00” appears in the display when

the unit is connected to AC outlet for the first

time, the battery may be weak. In this case,

consult a Sony dealer. The preinstalled CR2032

battery is considered part of the product, and is

covered by the warranty.

You are required to show “Note for customers in

Europe” (in this instruction) to a Sony dealer in

order to validate the warranty for this product.

To know when to replace the

battery

When the battery becomes weak, “ ” appears in 

the display.

If a power interruption occurs while the battery is

weak, the current time and alarm will be erased.

Replace the battery with a Sony CR2032 lithium

battery. Use of another battery may cause a fire or

explosion.

To replace the battery

1 Keep the AC plug connected to the AC

outlet, remove the screw that secures the

battery compartment lid at the bottom of

the unit using a screwdriver, and open

the lid (see Fig. ).

2 Insert a new battery in the battery

compartment with the side facing up 

(see Fig. ).

3 Close the battery compartment lid and

secure it with the screw (see Fig. ).

4 Press iPod & iPhone RADIO ,

BAND AUDIO IN SNOOZE/DATE/, or

SLEEP OFF to turn “ ” off in the 

display.

Note

When you replace the battery, do not disconnect

the plug from the AC outlet. Otherwise, the

calendar, current time, alarm and station presets

will be erased.





Reset button

CR2032

When Daylight Saving Time (summer time)

begins, the clock does not employ the

Daylight Saving Time automatically.



Make sure the clock is set correctly.



Press and hold CLOCK and SNOOZE/DATE/

SLEEP OFF simultaneously for at least

2 seconds to activate the Automatic DST

function.

Connecting the aerial

To connect the AM loop

aerial

The shape and the length of the aerial is designed

to receive AM signals. Do not dismantle or roll up

the aerial.

1 Remove only the loop part from the

plastic stand.

2 Set up the AM loop aerial.

3 Insert the AM aerial terminal into the

AM ANTENNA jack on the rear of the

unit.

To remove the AM loop aerial

Pull the AM aerial terminal while pushing up the

terminal clamp.

Adjusting the AM loop aerial

Find a place and an orientation that provide good

reception.



Do not place the AM loop aerial near the unit

or other AV equipment, as noise may result.

Tip

Adjust the direction of the AM loop aerial for best

AM broadcast sound.

Preparing the remote

commander

Before using the remote commander for the first

time, remove the insulation film.

To know when to replace the

battery

With normal use, the battery (CR2025) should

last for about six months. When the remote

commander no longer operates the unit, replace

the battery with a new one.

CR2025



If the time in the display is

incorrect after the battery is

changed (Reset)

Press the reset button with a pointed device. The

reset button is in the small hole located in the

battery compartment (see Fig. ). 

Personal Audio

Docking System

Operating Instructions

ICF-DS11iP

“ ” is displayed from the beginning of Daylight

Saving Time (summer time) and disappears at the

end of Daylight Saving Time (summer time)

automatically.

Automatic DST/Summer Time adjustment is

based on GMT (Greenwich Mean Time).

Area number 0:



Daylight Saving Time (summer time) begins at:

1:00 AM on the final Sunday of March.



Standard time begins at: 2:00 AM on the final

Sunday of October.

Area number 1:



Daylight Saving Time (summer time) begins at:

2:00 AM on the final Sunday of March.



Standard time begins at: 3:00 AM on the final

Sunday of October.

Area number 2:



Daylight Saving Time (summer time) begins at:

3:00 AM on the final Sunday of March.



Standard time begins at: 4:00 AM on the final

Sunday of October.

To cancel Automatic DST/Summer Time

adjustment during the Daylight Saving

Time (summer time) period

The Automatic DST/Summer Time adjustment

can be canceled.

Press and hold and CLOCK SNOOZE/DATE/

SLEEP OFF at the same time at least 2 seconds

while the clock is displayed.

“ ” and “OFF” appear in the display to show that

Automatic DST/Summer Time adjustment has

been canceled. The display returns to the clock.

Notes



Changes to Automatic DST/Summer Time

adjustment by the unit (see above) are subject

to circumstances and laws in each country/

region. Should this interfere with desired

adjustment, cancel the Automatic DST/Summer

Time adjustment and set the DST display

manually as necessary. Customers living in a

country/region that does not use Daylight

Saving Time (summer time) must cancel

Automatic DST/Summer Time adjustment

before using the unit.



To activate Automatic DST/Summer Time

adjustment again, press and hold CLOCK and

SNOOZE/DATE/SLEEP OFF at the same time

at least 2 seconds.

“ ” and “On” appear in the display to show that

Automatic DST/Summer Time adjustment has

been activated. The display returns to the clock.

Setting the clock manually

1 Plug in the unit.

2 Press and hold CLOCK until the year

flashes in the display.

3 Press or repeatedly to set TIME SET + –

the year.

4 Press CLOCK.

5 Repeat steps and to set the month, 3 4

day, hour and minute, and then press

CLOCK.

The seconds start incrementing from zero.

Notes



If you do not press any button for about

1 minute while setting the clock, the clock

setting will be canceled.

 A calendar is installed in this unit. When the

date is set, the day of the week is automatically

displayed.

MON = Monday, TUE = Tuesday,

WED = Wednesday, THU = Thursday,

FRI = Friday, SAT = Saturday, SUN = Sunday

To display the year and date

Press SNOOZE/DATE/SLEEP OFF SNOOZE ( on

the remote) once for the date, and press it again

for the year.

After a few seconds, the display will change back

to the current time automatically.

Setting the brightness

of the display

Three levels of brightness are available by pressing

BRIGHTNESS.

Even if you set the level of brightness to Low, it

will be changed to Middle, while alarm is

occurring.

Operating the radio

–Manual tuning

Press to turn on the radio.RADIO BAND

2 Press repeatedly to select RADIO BAND

the desired band.

Each press changes the band as follows:

FM1 FM2 AM

FM1 and FM2 are the same frequency bands.

3 Press or ( or on TUNING + – TUNE + –

the remote) to tune into the desired

station.

4 Adjust volume using VOLUME + – or

( or on the remote).VOL + –

To turn off the radio, press .OFF

Note

The FM frequency display is accurate to within

0.1 MHz. For example, frequency 88.00 and 88.05

MHz will be displayed as “88.0 MHz.”

Tuning in to a station

The unit automatically scans AM or FM stations.

1 Follow steps to in “Manual tuning” 1 2

and select the AM or FM band.

2 Press and hold or (TUNING + – TUNE +

or on the remote).–

+ : scans upward through the frequency bands.

–

scans downwards through the frequency

bands.

Scanning starts from the currently-tuned

frequency. When a station is received,

scanning stops.

3 Adjust the volume using VOLUME + – or

( or on the remote).VOL + –

–Preset tuning

You can preset up to 10 stations in FM (5 stations

in FM1, 5 stations in FM2), and 5 stations in AM.

Presetting a station

1 Follow steps to in “Manual tuning” 1 4

and manually tune into the station you

wish to preset.

2 Press and hold the desired STATION

SELECT PRESET 1 5 to buttons until

the preset number display changes from

flashing to fully lit.

Example: To preset FM 89.8 MHz onto the

preset button.1



After a while, the display will return to the

current time.

To preset another station, repeat these steps.

To change the preset station, tune into the

desired station and hold down the STATION

SELECT PRESET 1 5 to button. The new

station will replace the previous station on the

preset button.

Tuning in to a preset station

1 Follow steps to in “Manual tuning” 1 2

and select the AM or FM band.

2 Press one of the STATION SELECT

PRESET buttons where the desired

station is stored.

The preset station can also be selected by

PRESET + – or on the remote.

3 Adjust the volume using VOLUME + – or

( or on the remote).VOL + –

–Auto preset tuning

1 Follow steps to in “Manual tuning” 1 2

and select the AM or FM band.

2 Press and hold until “AP” RADIO BAND

flashes in the display.

3 Press DISPLAY/MEMORY.

The unit automatically presets the available

channels in order.

Tip

To stop auto preset tuning, press OFF/ALARM

RESET.

To display the preset number and

frequency of the current station

Press DISPLAY/MEMORY once for the preset

number, and press it again for the frequency.

If you press DISPLAY/MEMORY once only, the

display shows the preset number for about

2 seconds, then changes to the frequency.

After a few moments, the display returns to the

current time.

Improving the reception

FM: Extend the FM wire aerial fully to increase

reception sensitivity.

AM: Connect the supplied AM loop aerial to the

unit. Rotate the aerial horizontally for

optimum reception.

Notes on radio reception



Keep digital music players or mobile phones

away from the AM loop aerial or the FM aerial,

as this may lead to reception interference.



When you are listening to the radio with an

iPhone connected to the unit, interference with

radio reception may occur.



When you are listening to the radio while

charging an iPod, interference with radio

reception may occur.

Tip

If the FM broadcast is noisy, press until MODE

“MONO” appears in the display, the radio will

play in monaural and the sound will become

clearer.

Operating an iPod

You can enjoy audio from iPod by connecting to

this unit. To use an iPod, refer to the user’s guide

of your iPod.

If you are using an iPhone, iPhone 3G, iPhone

3GS or iPhone 4, attach the supplied universal

dock adapter for iPhone, iPhone 3G, iPhone 3GS

or iPhone 4 before connecting.

The adapter number, , or , is shown on   

the underside of the supplied universal dock

adapters. is for the iPhone, is for the iPhone  

3G & iPhone 3GS and is for the iPhone 4. 

Check the adapter number before use.

Setting the clock for

the first time

This unit is preset to the current date and time at

the factory, and is powered by the backup battery.

All you need to do the first time is just plug it in

and select your time zone.

1 Plug in the unit.

The current CET (Central European Time)

appears in the display.

2 Press and hold TIME ZONE for at least

2 seconds.

Area number “1” flashes in the display.

3 Press or repeatedly to TIME SET + –

select the number as follows:

Area number Time zone

1 (default

setting)

Central European Time/

Central European

Summer Time

Eastern European Time/

Eastern European

Summer Time

0 Western European Time/

Western European

Summer Time

4 Press TIME ZONE to set.

Note

Though the clock is correctly set at the factory,

discrepancies may arise during transport or

storage. If necessary, set the clock to the correct

time by referring to “Setting the clock manually.”

When Daylight Saving Time

(summer time) begins

This model automatically adjusts for Daylight

Saving Time (summer time).

 

Universal Dock Adapter



Notes



When inserting an iPod into the unit, be sure to

use the universal dock adapter supplied with your

iPod or commercially available from Apple Inc.



The connector of the unit is exclusively for use

with an iPod. If you use a device that does not

match the connector, connect it to the AUDIO

IN jack of this unit with the supplied audio

connecting cable.



Sony cannot accept responsibility in the event

that data recorded on an iPod is lost or damaged

when using an iPod connected to this unit.



For details of environmental conditions for

operating your iPod, check the website of Apple

Inc.

1 Attach the adapter for your iPod/iPhone.

2 Insert your iPod/iPhone into the

connector of the unit.

3 Press iPod & iPhone .

The iPod begins to play automatically.

You can operate the connected iPod by this

unit or the buttons on iPod.

4 Adjust the volume using VOLUME + or –

( or on the remote).VOL + –

To Press

Turn off the iPod OFF, or press and

hold iPod &

iPhone 

Pause playback iPod & iPhone



To resume play,

press it again.

Go to the next track  (forward)

Go back to the previous

track  (backward)*

Locate a point while

listening to the sound  (forward) or

 (backward)

while playing and

hold it until you

find the point.

Locate a point while

observing the display  (forward) or

 (backward)

in pause and hold

it until you find

the point.

Go back to the previous

MENU**

Select a menu item or a

track for playback   (up)/ (down)**

Execute the selected menu

or begin playback

ENTER**

Change to the shuffle mode

MODE

* During playback, this operation goes back to

the beginning of the current track. To go back

to the previous track, press twice.

** These operations are available only when using

the supplied remote commander.

Notes



When placing or removing the iPod, hold the

iPod at the same angle as that of the connector

on this unit, and do not twist or bend the iPod

as connector damage may result.



Do not carry the unit with an iPod set on the

connector. Doing so may cause a malfunction.



When placing or removing the iPod, hold the

Docking Tray securely with one hand and take

care not to press the controls of the iPod by

mistake.



Before disconnecting the iPod, pause playback.

To use the unit as a battery charger

You can use the unit as a battery charger.

Charging begins when the iPod is connected to

the unit.

Charging status appears in the display on iPod.

For details, see the user’s guide of your iPod.

On copyrights

iPhone, iPod, iPod classic, iPod nano, and iPod

touch are trademarks of Apple Inc., registered in

the U.S. and other countries.

“Made for iPod,” and “Made for iPhone” mean

that an electronic accessory has been designed to

connect specifically to iPod or iPhone,

respectively, and has been certified by the

developer to meet Apple performance standards.

Apple is not responsible for the operation of this

device or its compliance with safety and

regulatory standards. Please note that the use of

this accessory with iPod or iPhone may affect

wireless performance.

Setting the alarm

This unit is equipped with 3 alarm modes—iPod,

radio and buzzer. Before setting the alarm, make

sure to set the clock (see “Setting the clock for the

first time”).

To set the alarm

1 Press and hold or . ALARM SET A B

“WAKE UP” appears and the hour flashes in

the display.

2 Press or repeatedly until TIME SET + –

the desired hour appears.

To cycle the hour rapidly, press and hold TIME

SET + – or .

3 Press or . ALARM SET A B

The minute flashes.

4 Repeat step to set the minute.2

5 Press or . ALARM SET A B

The days of the week flash.

6 Repeat step to set the days of the week.2

You can select the days from the following

three options:

Every day: MON TUE WED THU FRI SAT

SUN

Week day: MON TUE WED THU FRI

Week end: SAT SUN

7 Press or . ALARM SET A B

The alarm mode setting is entered.

8 Press or repeatedly until TIME SET + –

the desired alarm mode flashes.

You can choose one of 5 settings: “iPod”,

“FM1”, “FM2”, “AM” or “BUZZER.” Set the

alarm mode as follows:

– iPod: see “ Setting the iPod alarm.”

– FM1, FM2 or AM: see “ Setting the radio

alarm.”

– BUZZER: see “ Setting the buzzer alarm.”

 Setting the alarm of iPod

Perform steps to in “To set the alarm.”1 8

2 Press or to select ALARM SET A B

alarm mode for “iPod.”

“VOLUME” appears in the display.

3 Press or to adjust the TIME SET + –

volume.

4 Press or . ALARM SET A B

The setting is entered.

5 If “A” or “B” does not appear in the

display, press or ALARM SET A B

again.

The iPod will sound at the set time.

When using an iPod touch/iPhone



To wake up to music stored in an iPod touch/

iPhone, connect the iPod touch/iPhone to the

unit first, follow the steps above to set alarm

time, and then select the music function.



Even if the alarm setting of iPod is complete, if

you turn the iPod touch/iPhone power off

before inserting the iPod touch/iPhone into the

unit, the alarm of iPod will not work.

 Setting the radio alarm

Perform steps to in “To set the alarm.”1 8

2 Press or to select ALARM SET A B

radio band (“FM1”, “FM2” or “AM”).

Preset number flashes in the display.

3 Press or to select the TIME SET + –

desired preset number corresponding the

bands or “– –”.

“– –” is the last station received.

4 Press or . ALARM SET A B

“VOLUME” appears in the display.

5 Press or to adjust the TIME SET + –

volume.

6 Press or . ALARM SET A B

The setting is entered.

7 If “A” or “B” does not appear in the

display, press or ALARM SET A B

again.

The radio will turn on at the set time.

 Setting the Buzzer Alarm

Perform steps to in “To set the alarm.”1 8

2 Press or to select ALARM SET A B

“BUZZER” alarm mode.

The setting is entered.

3 If “A” or “B” does not appear in the

display, press or ALARM SET A B

again.

The buzzer will sound at the set time.

Note

The volume cannot be set for the buzzer alarm.

To confirm an alarm time setting

Press or . The setting will be TIME SET + –

displayed for about 4 seconds.

To change an alarm setting

Press and hold for at least 2 seconds TIME SET +

to move the alarm time forwards. Press and hold

TIME SET – for at least 2 seconds to move the

alarm time back.

When you release the button, the changed time

will flash for about 2 seconds. To change the

alarm time again, press or within TIME SET + –

these 2 seconds, otherwise the setting change will

be fixed as displayed.

To doze for a few more minutes

Press SNOOZE/DATE/SLEEP OFF SNOOZE ( on

the remote).

The sound turns off but will automatically come

on again after about 10 minutes.

You can change the snooze time by pressing

SNOOZE/DATE/SLEEP OFF SNOOZE ( on the

remote) repeatedly within 4 seconds.

The maximum length of the snooze time is

60 minutes.

To stop the snooze timer, press OFF/ALARM

RESET OFF( on the remote).

To stop the alarm

Press ( on the remote) OFF/ALARM RESET OFF

to turn off the alarm.

The alarm will sound again at the same time the

next day.

To deactivate the alarm

Press or to turn off the ALARM ON/OFF A B

alarm A or B indicator from the display.

To activate the alarm

Press or to turn on the ALARM ON/OFF A B

alarm A or B indicator in the display.

Notes



With the alarm mode is set to iPod, when the

alarm time met, if iPod is not attached to the

unit, the alarm sound will be the buzzer.



The alarm function works as usual on the first

and last day of Daylight Saving Time (summer

time). As a result, if the Automatic DST/

Summer Time adjustment is set and the alarm

is set at a time skipped when the Daylight

Saving Time begins, the alarm is skipped; if the

alarm is set to a time that overlaps when

Daylight Saving Time ends, the alarm will

sound twice.



If the same alarm time is set for both alarm A

and B, alarm A takes priority.



If there is no operation while the alarm is

occurring, the alarm will stop after about

60 minutes.

Note on the alarm in the event of a power

interruption

In the event of a power interruption, the alarm

will work until the battery is totally discharged.

However, certain functions will be affected as

follows:



The backlight will not light up.



If the alarm mode is set to iPod or radio, it will

change to buzzer automatically.



If is not pressed, the alarm OFF/ALARM RESET

will sound for about 5 minutes.



If “ ” appears in the display, the alarm will not 

sound in the event of a power interruption.

Replace the battery if “ ” appears.



The snooze function cannot be set during a

power interruption. If the snooze function has

already been set and a power interruption

occurs, the snooze function will not work.



During a power interruption, each alarm will

sound at the set time only once.

Setting the sleep timer

You can fall asleep to music, etc., using the sleep

timer. The unit stops playback or radio

automatically after a preset duration.

1 Press while the unit is turned on. SLEEP

“SLEEP” appears and the sleep time flashes in

the display.

2 Press to set the sleep timer SLEEP

duration.

Each time you press , the duration (in SLEEP

minutes) changes as follows:

90 60 30 15

OFF

The display returns to clock mode for about

4 seconds after you have finished the duration

setting and released , and then the sleep SLEEP

timer starts.

The unit plays for the duration you set, and

then stops.

To turn off the unit before the preset

time

Press SNOOZE/DATE/SLEEP OFF SNOOZE ( on

the remote) or ( on the OFF/ALARM RESET OFF

remote).

To change the sleep timer setting

You can press repeatedly to select the SLEEP

desired sleep timer setting even after the sleep

timer has been activated.

To deactivate the sleep timer

Press repeatedly to set the sleep timer to SLEEP

“OFF” in step .2

Other useful functions

To get the MEGA Xpand effect

Press . “MEGA Xpand” appears in MEGA Xpand

the display. You can get the effect of expansion of

the sound field. To return to normal sound, press

the button again.

To reinforce the bass sound

Press . “MEGA BASS” appears in the MEGA BASS

display. You can get the effect of bass of high

quality sound. To return to normal sound, press

the button again.

Connecting external

equipment

To listen to sound

1 Connect the jack of the unit AUDIO IN

to the line out jack or headphone jack of

the external equipment using the audio

connecting cable (supplied).

Audio connecting cable

(supplied)

To external

equipment

2 Press AUDIO IN to display “AUDIO IN.”

3 Play the equipment connected to the

AUDIO IN jack.

Adjust the volume using VOLUME + – or

( or on the remote).VOL + –

To return to the radio

Press .RADIO BAND

First the preset number, then the frequency of the

last station is shown in the display.

To return to the iPod

Press iPod & iPhone .

To stop listening

Press ( on the remote), OFF/ALARM RESET OFF

and stop playback on the connected unit.

Notes



Refer also to the connected equipment’s manual.



The supplied audio connecting cable may not

be used with some external equipment. In this

case, use a cord suitable for the external

equipment you are using.



When you listen to the radio with external

equipment connected, turn off the connected

equipment to prevent noise. If noise occurs,

even when the equipment is turned off,

disconnect and place the external equipment

away from the unit.

The and VOL + buttons have a tactile dot.

PRESETSTATION SELECT

AC power cord

The STATION SELECT PRESET 3, VOLUME + and iPod & iPhone buttons have a 

tactile dot.

FM wire aerial

Produktspezifikationen

Marke:	Sony
Kategorie:	Ipod Audio
Modell:	ICF-DS11iP

Brauchst du Hilfe?

Wenn Sie Hilfe mit Sony ICF-DS11iP benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten

Ihren Namen*

Deine E-Mail*

Schreiben Sie hier Ihre Frage

Bedienungsanleitung Ipod Audio Sony

Sony ICF-DS11iP Bedienungsanleitung

4 Juli 2024

Bedienungsanleitung Ipod Audio

Neueste Bedienungsanleitung für -Kategorien-

XtremeMac Luna Voyager II Bedienungsanleitung

15 Oktober 2024

Boston Acoustics Duo-i plus Bedienungsanleitung

27 August 2024

Iluv iMM517 Bedienungsanleitung

25 August 2024

Iluv i9300 Bedienungsanleitung

25 August 2024

Iluv iMM514 Bedienungsanleitung

25 August 2024

EuroLine DMC 9600 Bedienungsanleitung

25 August 2024

Gear4 HouseParty AirWave Bedienungsanleitung

23 August 2024

Gear4 HouseParty Rise 2 Wireless Bedienungsanleitung

23 August 2024

Gear4 KRG-D50 Bedienungsanleitung

23 August 2024

Gear4 HouseParty SmartDock Bedienungsanleitung

23 August 2024