Sony HCD-BX6AV Bedienungsanleitung
Sony
Heimsystem
HCD-BX6AV
Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Sony HCD-BX6AV (64 Seiten) in der Kategorie Heimsystem. Dieser Bedienungsanleitung war für 16 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet
Seite 1/64
SERVICE MANUAL
COMPACT DISC DECK RECEIVER
US Model
Canadian Model
AEP Model
UK Model
HCD-BX6AV
E Model
Australian Model
HCD-DX6AV
SPECIFICATIONS
HCD-BX6AV/DX6AV
Photo: HCD-BX6AV
HCD-BX6AV/DX6AV is the Amplifier,
CD player, Tape player and Tuner
section in MHC-BX6AV/DX6AV.
Model Name Using Similar Mechanism HCD-BX2/DX2
CD Mechanism Type EXL-M7
Optical Pick-up Name OPTIMA-7
Model Name Using Similar Mechanism HCD-RXD6AV
Tape Transport Mechanism Type CWL-44-RR
CD
Section
Tape deck
Section
– Continued on next page –
AUDIO POWER SPECIFICATIONS:
(US model only)
POWER OUTPUT AND TOTAL
HARMONIC DISTORTION:
with 6 ohm loads both channels driven, from
120-10,000 Hz; rates 10 watts per channel
minimum RMS power, with no more than
10% total harmonic distortion from 250
milliwatts to rated output.
Amplifier section
US model
Center Speaker:
Continuous RMS power output (reference)
40 watts
(6 ohms at 1 kHz,
10% THD)
Rear Speaker:
Continuous RMS power output (reference)
40 + 40 watts
(6 ohms at 1 kHz,
10% THD)
Canadian model
Front Speaker:
Continuous RMS power output (reference)
60 + 60 watts
(6 ohms at 1 kHz,
10% THD)
Total harmonics distortion
Less than 0.07%
(6 ohms at 1 kHz, 30 W)
Center Speaker:
Continuous RMS power output (reference)
40 watts
(6 ohms at 1 kHz,
10% THD)
Rear Speaker:
Continuous RMS power output (reference)
40 + 40 watts
(6 ohms at 1 kHz,
10% THD)
AEP, UK models
Front Speaker:
DIN power output (rated) 40 + 40 watts
(6 ohms at 1 kHz, DIN)
Continuous RMS power output (reference)
50 + 50 watts
(6 ohms at 1 kHz,
10% THD)
Music power output (reference)
100 + 100 watts
(6 ohms at 1 kHz,
10% THD)
Center Speaker:
DIN power output (rated) 25 watts
(6 ohms at 1 kHz, DIN)
Continuous RMS power output (reference)
35 watts
(6 ohms at 1 kHz,
10% THD)
Music power output (reference)
70 watts
(6 ohms at 1 kHz,
10% THD)
Rear Speaker:
DIN power output (rated) 25 + 25 watts
(6 ohms at 1 kHz, DIN)
Continuous RMS power output (reference)
35 + 35 watts
(6 ohms at 1 kHz,
10% THD)
Music power output (reference)
70 + 70 watts
(6 ohms at 1 kHz,
10% THD)
Other models:
The following measured at AC 120/240 V,
50/60 Hz
Front Speaker:
DIN power output (rated) 45 + 45 watts
(6 ohms at 1 kHz, DIN)
Continuous RMS power output (reference)
60 + 60 watts
(6 ohms at 1 kHz,
10% THD)
Center Speaker:
DIN power output (rated) 30 watts
(6 ohms at 1 kHz, DIN)
Continuous RMS power output (reference)
40 watts
(8 ohms at 1 kHz,
10% THD)
Rear Speaker:
DIN power output (rated) 30 + 30 watts
(6 ohms at 1 kHz, DIN)
Continuous RMS power output (reference)
40 + 40 watts
(6 ohms at 1 kHz,
10% THD)
Inputs
MD/VIDEO IN: voltage 250/450 mV,
(phono jacks) impedance 47 kilohms
DVD INPUT:
FRONT IN: voltage 450 mV,
(phono jacks) impedance 47 kilohms
REAR IN: voltage 450 mV,
(phono jacks) impedance 47 kilohms
CENTER IN: voltage 450 mV,
(phono jacks) impedance 47 kilohms
WOOFER IN: voltage 450 mV,
(phono jacks) impedance 47 kilohms
Outputs
PHONES: accepts headphones of
(stereo mini jack) 8 ohms or more
FRONT SPEAKER: accepts impedance of 6 to
16 ohms
REAR SPEAKER: accepts impedance of 6 to
16 ohms
CENTER SPEAKER: accepts impedance of 6 to
16 ohms
WOOFER: Voltage 1 V, impedance
1 kilohms
CD player section
System Compact disc and digital
audio system
Laser Semiconductor laser
(λ=780nm)
Emission duration:
continuous
Laser output Max. 44.6
µ
W*
*This output is the value
measured at a distance of
200 mm from the
objective lens surface on
the Optical Pick-up Block
with 7 mm aperture.
Manufactured under license from Dolby
Laboratories Licensing Corporation.
Additionally licensed under Canadian patent
1,037,877. “Dolby”, the double-D symbol ; and
“PRO LOGIC” are trademarks of Dolby
Laboratories Licensing Corporation.
Ver 1.1 2001.07
9-929-250-12 Sony Corporation
2001G0500-1 Home Audio Company
C 2001.7 Shinagawa Tec Service Manual Production Group
2
ATTENTION AU COMPOSANT AYANT RAPPORT
À LA SÉCURITÉ!
LES COMPOSANTS IDENTIFIÉS PAR UNE MARQUE 0
SUR LES DIAGRAMMES SCHÉMATIQUES ET LA LISTE
DES PIÈCES SONT CRITIQUES POUR LA SÉCURITÉ
DE FONCTIONNEMENT. NE REMPLACER CES COM-
POSANTS QUE PAR DES PIÈCES SONY DONT LES
NUMÉROS SONT DONNÉS DANS CE MANUEL OU
DANS LES SUPPLÉMENTS PUBLIÉS PAR SONY.
SAFETY-RELATED COMPONENT WARNING!!
COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED
LINE WITH MARK 0 ON THE SCHEMATIC DIAGRAMS
AND IN THE PARTS LIST ARE CRITICAL TO SAFE
OPERATION. REPLACE THESE COMPONENTS WITH
SONY PARTS WHOSE PART NUMBERS APPEAR AS
SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUB-
LISHED BY SONY. CAUTION
Use of controls or adjustments or performance of procedures
other than those specified herein may result in hazardous ra-
diation exposure.
Wavelength 780 – 790 nm
Frequency response 20 Hz – 20 kHz (±0.5 dB)
Signal-to-noise ratio More than 90 dB
Dynamic range More than 90 dB
CD OPTICAL DIGITAL OUT
(Square optical connector jack, rear panel)
Wavelength 660 nm
Output Level –18 dBm
Tape player section
Recording system 4-track 2-channel stereo
Frequency response 40 – 13,000 Hz (±3 dB),
using Sony TYPE I cassette
Tuner section
FM stereo, FM/AM superheterodyne tuner
FM tuner section
Tuning range 87.5 – 108.0 MHz
Antenna FM lead antenna
Antenna terminals 75 ohm unbalanced
Intermediate frequency 10.7 MHz
AM tuner section
Tuning range
US, Canadian models: 530 – 1,710 kHz
(with the interval set at
10 kHz)
531 – 1,710 kHz
(with the interval set at
9 kHz)
AEP, UK and Middle Eastern models:
531 – 1,602 kHz
(with the interval set at
9 kHz)
Other models: 531 – 1,602 kHz
(with the interval set at
9 kHz)
530 – 1,710 kHz
(with the interval set at
10 kHz)
Antenna AM loop antenna
Antenna terminals External antenna terminal
Intermediate frequency 450 kHz
General
Power requirements
US, Cnadian models: 120 V AC, 60 Hz
AEP, UK models: 230 V AC, 50/60 Hz
Australian model: 220 – 240 V AC, 50/60 Hz
Mexican model: 120 V AC, 60 Hz
Other models: 110 – 120 V or 220 – 240 V AC, 50/
60 Hz
Adjustable with voltage selector
Power consumption
US model: 160 watts
Canadian model: 180 watts
AEP, UK models: 160 watts
Other models: 160 watts
Dimensions (w/h/d)
Approx. 280 x 325 x 390 mm
Mass
US model: Approx. 9.2 kg
Canadian model: Approx. 9.2 kg
AEP, UK models: Approx. 9.2 kg
Other model: Approx. 9.1 kg
Supplied accessories: AM loop antenna (1)
FM lead antenna (1)
Remote Commander (1)
Speaker cords (2)
Center speaker pads (4)
Design and specifications are subject to change
without notice.
This appliance is classified
as a CLASS 1 LASER
product. The CLASS 1
LASER PRODUCT
MARKING is located on
the rear exterior.
TABLE OF CONTENTS
1. SERVICING NOTES............................................... 3
2. GENERAL
Location of Controls ....................................................... 4
Setting the Time .............................................................. 5
3. DISASSEMBLY ......................................................... 6
4. DIAGRAMS
4-1. Note for Printed Wiring Boards and
Schematic Diagrams ....................................................... 11
4-2. Schematic Diagram – CD Section (1/4) – ..................... 12
4-3. Schematic Diagram – CD Section (2/4) – ..................... 13
4-4. Schematic Diagram – CD Section (3/4) – ..................... 14
4-5. Schematic Diagram – CD Section (4/4) – ..................... 15
4-6. Printed Wiring Boards – CD Section – ......................... 16
4-7. Printed Wiring Boards – MAIN Section – .................... 17
4-8. Schematic Diagram – MAIN Section (1/4) –................ 18
4-9. Schematic Diagram – MAIN Section (2/4) –................ 19
4-10. Schematic Diagram – MAIN Section (3/4) – ................ 20
4-11. Schematic Diagram – MAIN Section (4/4) –................ 21
4-12. Printed Wiring Boards – PANEL Section – .................. 22
4-13. Schematic Diagram – PANEL Section – ....................... 23
4-14. Printed Wiring Boards
– AMP/POWER SUPPLY Section – ............................. 24
4-15. Schematic Diagram – FRONT AMP Section – ............ 25
4-16. Schematic Diagram
– CENTER/REAR AMP Section –................................. 26
4-17. Schematic Diagram – POWER SUPPLY Section –...... 27
5. EXPLODED VIEWS ................................................ 33
6. ELECTRICAL PARTS LIST ............................... 39
Notes on chip component replacement
• Never reuse a disconnected chip component.
• Notice that the minus side of a tantalum capacitor may be dam-
aged by heat.
Flexible Circuit Board Repairing
• Keep the temperature of the soldering iron around 270 ˚C dur-
ing repairing.
• Do not touch the soldering iron on the same conductor of the
circuit board (within 3 times).
• Be careful not to apply force on the conductor when soldering
or unsoldering.
3
SECTION 1
SERVICING NOTES
The laser diode in the optical pick-up block may suffer electro-
static break-down because of the potential difference generated
by the charged electrostatic load, etc. on clothing and the human
body.
During repair, pay attention to electrostatic break-down and also
use the procedure in the printed matter which is included in the
repair parts.
The flexible board is easily damaged and should be handled with
care.
NOTES ON LASER DIODE EMISSION CHECK
The laser beam on this model is concentrated so as to be focused
on the disc reflective surface by the objective lens in the optical
pick-up block. Therefore, when checking the laser diode emis-
sion, observe from more than 30 cm away from the objective lens.
• MODEL IDENTIFICATION
– Rear Panel –
NOTES ON HANDLING THE OPTICAL PICK-UP
BLOCK OR BASE UNIT
Model Power Voltage Indication
US model AC: 120 V - 60 Hz 160 W
Canadian model AC: 120 V - 60 Hz 180 W
AEP, UK models AC: 230 V - 50/60 Hz 160 W
Australian model AC: 220 – 240 V - 50/60 Hz 160 W
Mexican model AC: 120 V - 50/60 Hz 160 W
Other models AC: 110 – 120 V/220 – 240 V - 50/60 Hz 160 W
Power Voltage Indication
SAFETY CHECK-OUT
After correcting the original service problem, perform the follow-
ing safety check before releasing the set to the customer:
Check the antenna terminals, metal trim, “metallized” knobs,
screws, and all other exposed metal parts for AC leakage.
Check leakage as described below.
LEAKAGE TEST
The AC leakage from any exposed metal part to earth ground and
from all exposed metal parts to any exposed metal part having a
return to chassis, must not exceed 0.5 mA (500 microamperes.).
Leakage current can be measured by any one of three methods.
1. A commercial leakage tester, such as the Simpson 229 or RCA
WT-540A. Follow the manufacturers’ instructions to use these
instruments.
2. A battery-operated AC milliammeter. The Data Precision 245
digital multimeter is suitable for this job.
3. Measuring the voltage drop across a resistor by means of a
VOM or battery-operated AC voltmeter. The “limit” indica-
tion is 0.75 V, so analog meters must have an accurate low-
voltage scale. The Simpson 250 and Sanwa SH-63Trd are ex-
amples of a passive VOM that is suitable. Nearly all battery
operated digital multimeters that have a 2 V AC range are suit-
able. (See Fig. A)
Fig. A. Using an AC voltmeter to check AC leakage.
1.5 k
Ω
0.15 µF
AC
voltmeter
(0.75 V)
To Exposed Metal
Parts on Set
Earth Ground
The following caution label is located inside the unit.
Produktspezifikationen
| Marke: | Sony |
| Kategorie: | Heimsystem |
| Modell: | HCD-BX6AV |
Brauchst du Hilfe?
Wenn Sie Hilfe mit Sony HCD-BX6AV benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten
Bedienungsanleitung Heimsystem Sony
1 Juli 2024
Bedienungsanleitung Heimsystem
Neueste Bedienungsanleitung für -Kategorien-
22 August 2024
15 August 2024
14 Juli 2024
4 Juli 2024
4 Juli 2024
4 Juli 2024
4 Juli 2024
4 Juli 2024
3 Juli 2024
3 Juli 2024