Sony Dream Machine ICF-C273 Bedienungsanleitung

Sony Radiowecker Dream Machine ICF-C273

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Sony Dream Machine ICF-C273 (2 Seiten) in der Kategorie Radiowecker. Dieser Bedienungsanleitung war für 15 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Download PDF
Seite 1/2
3-263-574- (1)21
FM/AM
PLL Synthesized
Clock Radio
Operating Instructions
ICF-C273
© 2004 Sony Corporation Printed in China
Dream Machine is a trademark of Sony Corporation.
IMPORTANT SAFEGUARDS
For your protection, please read these safety instructions completely before operating the appliance,
and keep this manual for future reference.
Carefully observe all warnings, precautions and instructions on the appliance and in the operating
instructions, and adhere to them.
INSTALLATION
Water and Moisture
Do not use powerline operated appliances near water - for example, near a bathtub, washbowl,
kitchen sink, or laundry tub, in a wet basement, or near a swimming pool, etc.
Heat
Do not place the appliance near or over a radiator or heat register, or where it is exposed to direct
sunlight.
Ventilation
The slots and openings in the cabinet are provided for necessary ventilation. To ensure reliable
operation of the appliance, and to protect it from overheating, these slots and openings must never be
blocked or covered.
-Never cover the slots and openings with a cloth or other materials.
-Never block the slots and openings by placing the appliance on a bed, sofa, rug or other similar
surface.
-Never place the appliance in a confined space, such as a bookcase, or built-in cabinet, unless proper
ventilation is provided.
Accessories
Do not place the appliance on an unstable cart, stand, tripod, bracket, or table. The appliance may fall,
causing serious injury to a child or an adult, and serious damage to the appliance. Use only a cart,
stand, tripod, bracket, or table recommended by Sony.
-An appliance and cart combination should be moved with care. Quick stops, excessive force, and
uneven surfaces may cause the appliance and cart combination to overturn.
Wall or Ceiling Mounting
If your appliance can be mounted to a wall or ceiling, mount it only as recommended by Sony.
USE
Power Source
This appliance should be operated only from the type of power source indicated on the marking label.
If you are not sure of the type of electrical power supplied to your home, consult your dealer or local
power company. For those appliances designed to operate from battery power, or other sources, refer
to the operating instructions.
Grounding or Polarization
This appliance is equipped with a polarized AC power cord plug (a plug having one blade wider than
the other), or with a three-wire grounding type plug (a plug having a third pin for grounding). Follow
the instructions below:
-For the appliance with a polarized AC power cord plug:
This plug will fit into the power outlet only one way. This is a safety feature. If you are unable to
insert the plug fully into the outlet, try reversing the plug. If the plug should still fail to fit, contact
your electrician to have a suitable outlet installed. Do not defeat the safety purpose of the polarized
plug by forcing it in.
-For the appliance with a three-wire grounding type AC plug:
This plug will only fit into a grounding-type power outlet. This is a safety feature. If you are unable to
insert the plug into the outlet, contact your electrician to have a suitable outlet installed. Do not defeat
the safety purpose of the grounding plug.
Overloading
Do not overload wall outlets, extension cords or convenience receptacles beyond their capacity, since
this can result in fire or electric shock.
When not in use
Unplug the power cord of the appliance from the outlet when left unused for a long period of time.
To disconnect the cord, pull it out by grasping the plug. Never pull the plug out by the cord.
Power-Cord Protection
Route the power cord so that it is not likely to be walked on or pinched by items placed upon or
against them, paying particular attention to the plugs, receptacles, and the point where the cord exits
from the appliance.
Lightning
For added protection for this appliance during a lightning storm, or when it is left unattended and
unused for long periods of time, unplug it from the wall outlet and disconnect the antenna or cable
system. This will prevent damage to the appliance due to lightning and powerline surges.
Object and Liquid Entry
Never push objects of any kind into the appliance through openings as they may touch dangerous
voltage points or short out parts that could result in a fire or electric shock. Never spill liquid of any
kind on the appliance.
Cleaning
Unplug the appliance from the wall outlet before cleaning or polishing it. Do not use liquid cleaners
or aerosol cleaners. Use a cloth lightly dampened with water for cleaning the exterior of the appliance.
Clean the appliance only as recommended by Sony.
Attachments
Do not use attachments not recommended by Sony, as they may cause hazards.
ANTENNAS
Outdoor Antenna Grounding
If an outdoor antenna or cable system is installed, follow the precautions below.
An outdoor antenna system should not be located in the vicinity of overhead power lines or other
electric light or power circuits, or where it can come in contact with such power lines or circuits.
WHEN INSTALLING AN OUTDOOR ANTENNA SYSTEM, EXTREME CARE SHOULD BE TAKEN
TO KEEP FROM CONTACTING SUCH POWER LINES OR CIRCUITS AS CONTACT WITH THEM
IS ALMOST INVARIABLY FATAL.
Be sure the antenna system is grounded so as to provide some protection against voltage surges and
built-up static charges. Section 810 of the National Electrical Code provides information with respect
to proper grounding of the mast and supporting structure, grounding of the lead-in wire to an
antenna discharge unit, size of grounding conductors, location of antenna-discharge unit, connection
to grounding electrodes, and requirements for the grounding electrode.
Antenna Grounding According to the National
Electrical Code
SERVICE
Damage Requiring Service
Unplug the appliance from the wall outlet and refer servicing to qualified service personnel under the
following conditions:
-When the power cord or plug is damage or frayed.
-If liquid has been spilled or objects have fallen into the appliance.
-If the appliance has been exposed to rain or water.
-The appliance does not appear to operate normally or exhibits a marked change in performance.
-This indicates a need for service.
-If the appliance does not operate normally when following the operating instructions, adjust only
those controls that are specified in the operating instructions. Improper adjustment of other controls
may result in damage and will often require extensive work
by a qualified technician to restore the appliance to normal operation.
-If the appliance has been subject to excessive shock by being dropped, or the cabinet has been
damaged.
Servicing
Do not attempt to service the appliance yourself as opening or removing covers may expose you to
dangerous voltage or other hazards.
Refer all servicing to qualified service personnel.
Replacement parts
When replacement parts are required, be sure the service technician has used replacement parts
specified by Sony that have the same characteristics as the original parts.
Unauthorized substitutions may result in fire, electric shock, or other hazards.
Safety Check
Upon completion of any service or repairs to the appliance, ask the service technician to perform
routine safety checks (as specified by Sony) to determine that the appliance is in safe operating
condition.
Antenna Discharge Unit
(NEC Section 810-20)
Grounding Conductors
(NEC Section 810-20)
Antenna Lead-in Wire
Ground
Clamps
NEC-NATIONAL
ELECTRICAL CODE
Electric Service
Equipment Ground Clamps
Power Service Grounding Electrode System
(NEC Art 250 Part H)
For customers who purchased this product in the
USA
Please register this product on line at
http://www.sony.com/productregistration.
Proper registration will enable us to send you
periodic mailings about new products, services,
and other important announcements. Registering
your product will also allow us to contact you in
the unlikely event that the product needs
adjustment or modification. Thank you.
WARNING
To prevent fire or shock hazard, do not
expose the unit to rain or moisture.
To avoid electrical shock, do not open the cabinet.
Refer servicing to qualified personnel only.
Do not install the appliance in a confined space, such
as a bookcase or built-in cabinet.
To prevent fire or shock hazard, do not place objects
filled with liquids, such as vases, on the apparatus.
This symbol is intended to alert the
user to the presence of uninsulated
“dangerous voltage” within the
product’s enclosure that may be of
sufficient magnitude to constitute a
risk of electric shock to persons.
This symbol is intended to alert the
user to the presence of important
operating and maintenance
(servicing) instructions in the
literature accompanying the
appliance.
∗The graphical symbols are at the bottom of
the unit.
WARNING
You are cautioned that any changes or
modifications not expressly approved in
this manual could void your authority to
operate this equipment.
INFORMATION
This equipment has been tested and found to comply
with the limits for a Class B digital device, pursuant to
Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful
interference in a residential installation. This
equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful
interference to radio communications. However, there
is no guarantee that interference will not occur in a
particular installation. If this equipment does cause
harmful interference to radio or television reception,
which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the
interference by one or more of the following
measures:
— Reorient or relocate the receiving
antenna.
— Increase the separation between the
equipment and receiver.
— Connect the equipment into an outlet
on a circuit different from that to
which the receiver is connected.
— Consult the dealer or an experienced
radio/TV technician for help.
Features
• Dual alarm FM/AM PLL (phase locked loop)
synthesized clock radio.
• Triple time display – main display for the clock, and
two sub-displays for the alarms.
• Green backlight LCD with adjustable brightness.
• Date button to display the year, month and day.
• Easy preset digital tuning with 15 memory presets.
• D.S.T. (Daylight Saving Time) – Summer time
adjustment (one-hour skip function).
• Various types of alarms-radio, buzzer and 2
melodies.
• Extendable snooze – snooze time can be extended
from 10 to 60 minutes (maximum).
• Nap Timer allows you to take a short nap and wake
to buzzer without changing your alarm settings.
(You can select your nap time from 10 to 120
minutes)
Troubleshooting
Should any problem occur with the unit, make the
following simple checks to determine whether or not
servicing is required.
If the problem persists, consult your nearest Sony
dealer.
The clock does not show the correct time.
• Has an electrical power outage lasting more than 1
minutes occurred?
The radio or buzzer alarm does not sound at
the preset alarm time.
• Has the desired radio or buzzer alarm been
activated? (i.e. Is the display ALARM A or B turned
on?)
The radio alarm is activated but no sound
comes on at the preset alarm time.
• Has VOLUME been adjusted ?
Precautions
• Operate the unit only on 120 V AC, 60 Hz.
• To disconnect the power cord (mains lead), pull it
out by the plug, not the cord.
• Do not leave the unit in a location near a heat
source, such as a radiator or airduct, or in a place
subject to direct sunlight, excessive dust,
mechanical vibration, or shock.
• Allow adequate air circulation to prevent internal
heat build-up. Do not place the unit on a surface (a
rug, blanket, etc.) or near materials (a curtain) that
might block the ventilation holes.
• Should any solid object or liquid fall into the unit,
unplug the unit and have it checked by a qualified
personnel before operating it any further.
• To clean the casing, use a soft cloth dampened with
a mild detergent solution.
If you have any questions or problems
concerning your unit, please consult your
nearest Sony dealer.
Specifications
Time display
12-hour system
Frequency range
FM: 87.5–108 MHz
AM: 530–1 710 kHz
Channel steps
FM: 0.1 MHz (fixed)
AM: 10 kHz (fixed)
Speaker
Approx. 6.6 cm (2 5/8 in.) dia., 8 Ω
Power output
200 mW (at 10% harmonic distortion)
Power requirements
120 V AC, 60 Hz
Dimensions
Approx. 173 × 57.2 × 133.5 mm (w/h/d)
(6 7/ 8× 2 3/8
× 5 3/8 in.) incl. projecting parts and
controls
Mass
Approx. 630 g (1 lb. 6.2 oz.)
Design and specifications are subject to change
without notice.
Printed on 100% recycled paper using
VOC (Volatile Organic Compound)-
free vegetable oil based ink.
Lead-free solder is used for soldering.
Halogenated flame retardants are not
used in printed wiring boards.
Setting the Clock
and Date
1Plug in the clock radio.
The display will flash “AM 12:00”.
2Press CLOCK for a few seconds.
You will hear a beep and the year will start to
flash in the display.
3Press Jog lever (up) or (down) untilv V
the correct year appears in the display.
4Press .ENTER/BRIGHTNESS
5Repeat steps to set the month, day,3 4 and
hour, and minute.
After setting the minute, press ENTER/
BRIGHTNESS to start the counting of the
seconds, and you will hear two short beeps.
• To set the current time rapidly, hold down Jog lever
v V (up) or (down).
• In step 5, when you press ENTER/BRIGHTNESS
after the minute setting to activate the clock, the
seconds start counting from zero.
• When the alarm setting mode is entered, the clock
cannot be set.
To display the year and date
Press SNOOZE/DATE/SLEEP OFF once for the
date, and within 2 seconds press it again for the year.
The display shows the date or year for a few seconds
and then changes back to the current time.
To change the display to the
daylight saving time (summer
time) indication
Press D.S.T./SUMMER T.
“ ” is displayed and the time indication changes to
summer time.
To deactivate the summer time function, press
D.S.T./SUMMER T. again.
To set the brightness of the
backlight
If you cannot see the display clearly, press and hold
ENTER/BRIGHTNESS to set the desired brightness
(high, middle or low).
AC power cord
FM wire antenna
Changing AM
Channel Step
The AM channel step differs depending on area. The
channel step of this unit is factory-set to 10 kHz to
change the setting as shown below to be able to listen
to the radio.
Area Channel step
North and South America 10 kHz
Other countries/regions 9 kHz
1Plug in the clock radio.
Press OFF/ALARM RESET to turn off the
power.
2While holding down OFF/ALARM
RESET ON/BAND, keep pressing for
more than 5 seconds.
The AM channel step will be changed.
If you proceed to step again, the channel step2
changes again.
Notes
• When the AM channel step is changed, the preset
stations for AM will be initialized.
• When the AM channel step is changed, the FM
channel step also will be changed.
Playing the Radio
—Manual Tuning
1Press ON/BAND to turn on the radio.
The display shows the band and frequency for a
few seconds and then changes back to the current
time.
2Press ON/BAND repeatedly to select the
desired band.
Each press changes the band as follows:
AM FM1 FM2
When using FM1 or FM2 preset mode, you may
listen to the radio on either mode. (See “Presetting
Your Favourite Station”.)
3Use or TUNING + – to tune into the
desired station.
The FM frequency advances or reverses in 0.1
MHz channel steps and the AM frequency in 10
kHz channel steps.
Two short beeps sound when the minimum
frequency of each band is received during tuning.
4Adjust volume using VOLUME.
• To turn off the radio, press OFF/ALARM RESET.
• To check the station being received, press TUNING
+ – ON/BAND or or lightly. The display shows the
band and frequency for a few seconds and then
changes back to the current time.
Improving the
Reception
FM: Extend the FM wire antenna fully to
increase reception sensitivity.
AM: Rotate the unit horizontally for optimum
reception. A ferrite bar is built in to the
unit.
Do not operate the unit over a steel desk or metal
surface, as this may lead to interference of reception.
Presetting Your
Favourite Station
—Preset Tuning
You can preset up to 10 stations in FM (5 stations in
FM1, 5 stations in FM2), and 5 stations in AM.
Presetting a Station
1Follow steps 1 4 to in “Playing the Radio”
and manually tune into the station you
wish to preset.
2Hold down the desired
STATION•SELECT/PRESET button
until you hear two short beeps.
Example: To preset AM 1 260 kHz onto preset
2 button.
The display shows the frequency for a few
seconds and then changes back to the current
time.
To preset another station, repeat these steps.
To change the preset station, tune into the desired
station and hold down the PRESET TUNING 1
to 5 button. The new station will replace the
previous station on the preset button.
Tuning into a preset station
1Press ON/BAND to turn on the radio.
2Press STATION•SELECT/PRESET
where the desired station is stored.
3Adjust volume using VOLUME.
After a few seconds, the display will return to the
current time but the preset button number will
remain.
Setting the Alarm
You can choose from two types of alarm, Radio or
Buzzer.
The alarm will come on at the same time everyday.
The factory setting alarm time for the radio and
buzzer is 12:00am.
Notes
• Set the current time before setting the alarm.
• Radio reception is interrupted while the alarm time
is being set.
To set the Alarm Time
1Press and hold ALARM A or ALARM B
for a few seconds.
After one beep, the hour flashes in the alarm
display.
2Press Jog lever (up) or (down) tov V
select the hour.
To set the hour rapidly, hold down Jog lever v
(up) or V (down).
3Press .ENTER/BRIGHTNESS
After one beep, the minutes flash on the alarm
display.
4Repeat steps to set the minute.2 3 and
A beep sounds to confirm the time setting.
“RADIO•SOUND” appears.
You can choose between “RADIO” and
“SOUND” modes.
Set the alarm mode as follows:
• RADIO: see “A Setting the Radio Alarm”
• SOUND: see “B Setting the Sound Alarm”
A Setting the Radio Alarm
For the radio alarm, the station you specified as the
wake-up station is played.
1Perform steps in “To set the Alarm1 4 to
Time.”
2Press Jog lever (up) or (down) tov V
select “RADIO” alarm mode.
“WAKE UP STATION” appears in the display.
3Press .ENTER/BRIGHTNESS
After one beep, the preset number flashes in the
display.
4Press Jog lever (down) to selectv (up) or V
the desired wake-up station.
Preset number changes in the order as follows:
“P-” is the last received station.
You can directly select the desired wake-up
station by pressing ON/BAND or the
STATION•SELCET/PRESET button while the
indication “P-” is not displayed.
5Press .ENTER/BRIGHTNESS
Two short beeps will confirm the setting, and the
ALARM A or B display will disappear.
B Setting the Sound Alarm
For the sound alarm, the sound you specified as the
wake-up sound is played.
1Perform steps in “To set the Alarm1 4 to
Time.”
2Press Jog lever (up) or (down) tov V
select “SOUND” alarm mode.
“WAKE UP SOUND” appears in the display.
3Press .ENTER/BRIGHTNESS
The displayed wake-up sound number will sound.
4Press Jog lever (up) or (down) tov V
select the desired wake-up sound.
1: Buzzer
2: “Four seasons: Spring” Antonio Lucio Vivaldi
3: “For Eliza” Ludwig van Beethoven
5Press .ENTER/BRIGHTNESS
Two short beeps will confirm the setting, and the
ALARM A or B display will disappear.
To Use the Radio and Buzzer
Alarm
1Set both alarm times for ALARM A or
ALARM B. (see above).
2Press or .ALARM A B
The ALARM A or B display will be turned on.
If the same alarm time is set for both Alarm A and B,
Alarm A takes priority.
To Doze for a Few More Minutes
Press .SNOOZE/DATE/SLEEP OFF
The radio or buzzer turns off but will automatically
come on again after about 10 minutes. Every time you
press SNOOZE/DATE/SLEEP OFF, the snooze
time changes as follows:
The display shows the snooze time for a few seconds
and returns to show the current time. When you press
SNOOZE/DATE/SLEEP OFF after the current time
appeared, the snooze time starts from 10 minutes
again.
The maximum length of the snooze time is 60
minutes.
To Stop the Alarm
Press OFF/ALARM RESET to turn off the
alarm.
The alarm will come on again at the same time the
next day.
To Deactivate the Alarm
Press .ALARM A or ALARM B
The ALARM A or B display turns off.
Using the NAP Timer
(Count Down Timer)
The NAP timer sounds the buzzer after a preset time
duration.
Press repeatedly until the desired minutes areNAP
displayed.
Every press changes the display as follows:
You will hear two beeps when the display turns from
“OFF” to “10”.
“ ” appears and the NAP time is displayed for a
few seconds.
NAP timer starts counting down the NAP time.
When selected NAP time has passed, the beep sound
comes on, and “ ” on the display flash.
The buzzer is turned off automatically after about 60
minutes.
To Stop the NAP Timer
Press NAP or OFF/ALARM RESET to turn off the
buzzer.
To Deactive the NAP Timer
Press .NAP
“ ” goes off in the display.
Setting the Sleep
Timer
You can fall asleep to the radio using the built-in
sleep timer that turns off the radio automatically after
a preset duration.
Press .SLEEP
The radio turns on. You can set the sleep timer to
durations of 90, 60, 30, or 15 minutes. Every push
changes the display as follows:
You will hear two beeps when the display turns from
“OFF” to “90”.
“SLEEP” will appear in the display when the duration
time is set.
The radio will play for the duration you set, then shut
off.
• To turn off the radio before the preset time, press
SNOOZE/DATE/SLEEP OFF.
To Use Both Sleep Timer and
Alarm
You can fall asleep to the radio and also be awakened
by the radio or buzzer alarm at a preset time.
1Set the alarm. (See “Setting the Alarm”.)
2Set the sleep timer. (See “Setting the Sleep
Timer”.)
Jog lever
VOLUME
There is a tactile dot beside
volume to show the direction
to turn up the volume.
The PRESET TUNING 3 button has
a tactile dot.

Produktspezifikationen

Marke: Sony
Kategorie: Radiowecker
Modell: Dream Machine ICF-C273

Brauchst du Hilfe?

Wenn Sie Hilfe mit Sony Dream Machine ICF-C273 benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten


Bedienungsanleitung Radiowecker Sony

Sony

Sony ICF-CD820 Bedienungsanleitung

1 September 2024
Sony

Sony ICF-7600D Bedienungsanleitung

23 August 2024
Sony

Sony ICF-C60LRC Bedienungsanleitung

1 August 2024
Sony

Sony ICF-CD832PS Bedienungsanleitung

19 Juli 2024
Sony

Sony ICF-C705 Bedienungsanleitung

4 Juli 2024
Sony

Sony ICF-CD853V Bedienungsanleitung

4 Juli 2024
Sony

Sony ICF-C203 Bedienungsanleitung

4 Juli 2024
Sony

Sony ICF-C317L Bedienungsanleitung

2 Juli 2024
Sony

Sony ICF-C1IP MK-II Bedienungsanleitung

2 Juli 2024
Sony

Sony ICF-CD837 Bedienungsanleitung

2 Juli 2024

Bedienungsanleitung Radiowecker

Neueste Bedienungsanleitung für -Kategorien-

Logik

Logik LCRA14 Bedienungsanleitung

16 Oktober 2024
Insignia

Insignia NS-ALCL24 Bedienungsanleitung

15 Oktober 2024
ICES

ICES ICR-232 Bedienungsanleitung

13 Oktober 2024
AEG

AEG MRC 4116 Bedienungsanleitung

13 Oktober 2024
Caliber

Caliber HCG015 Bedienungsanleitung

11 Oktober 2024
Grundig

Grundig Sonoclock 50L Bedienungsanleitung

8 Oktober 2024
La Crosse Technology

La Crosse Technology soluna W74146 Bedienungsanleitung

8 Oktober 2024
La Crosse Technology

La Crosse Technology 616A-30357 Bedienungsanleitung

7 Oktober 2024
Muse

Muse M-188P Bedienungsanleitung

5 Oktober 2024
La Crosse Technology

La Crosse Technology 617-710 Bedienungsanleitung

3 Oktober 2024