Sonance Visual Performance Extreme VPXT6 Bedienungsanleitung

Sonance Lautsprecher Visual Performance Extreme VPXT6

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Sonance Visual Performance Extreme VPXT6 (3 Seiten) in der Kategorie Lautsprecher. Dieser Bedienungsanleitung war für 27 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Download PDF
Seite 1/3
Box Contents
VPXT6 or VPXT6R or VPXT8R
(1) Quickstart guide / cutout template
(2) Speakers
(2) Paintable grilles
Or
VPXT6R SST
(1) Quickstart guide / cutout template
(1) Speaker
(1) Paintable grille
EXTREME SPEAKERS INSTRUCTION MANUAL
VPXT6 | VPXT6R | VPXT6R SST | VPXT8R
SONANCE VISUAL PERFORMANCE SERIES
Introduction
Thank you for purchasing Sonance Visual Performance
Series Speakers. This guide covers the following speaker
models: VPXT6 (6” Rectangular), VPXT6R (6” Round),
VPXT6R SST (6” Round, Single-Stereo Technology®) and
VPXT8R (8” Round).
Before Installation: Retro-t
1. Determine the location for the speaker.
2. Perform an obstruction survey to be certain that there are
no studs, conduit, pipes, heating ducts, pocket doors
or air returns in the wall cavity that will interfere with
the speaker.
3. Position the included cutout template where the
speaker is to be located and pencil an outline on the
wall or ceiling.
• If you are unsure about obstructions, drill a small hole
in the center of the outline and insert a coat hanger wire
into the hole to feel-around for possible obstructions.
4. Cut the mounting hole using tools appropriate for the
construction, and run the speaker wires from the
mounting hole to the amplier location.
Installation
Sonance Visual Performance Series Extreme speakers
feature an exclusive integral RotoLock® mounting system for
quick mounting directly into existing walls and ceilings.
1. Strip 1/4” – 1/2” (6mm – 13mm) of insulation from each
speaker lead. Twist the strands or tin the exposed wire
with solder to ensure that there are no stray strands.
1
NOTE: CONSULT LOCAL BUILDING CODES BEFORE RUNNING
SPEAKER WIRES THROUGH WALLS.
NOTE: STRAY STRANDS THAT TOUCH EACH OTHER CAN CAUSE A
SHORT- CIRCUIT THAT CAN DAMAGE THE AMPLIFIER.
2. The speaker’s connector posts are spring-loaded.
Push the top of each connector post down to open the
connector and insert the exposed wires into the holes in
the posts (see Figure 1).
3. The speaker’s positive post is labeled with a red dot; the
negative post is labeled with a black dot.
• The VPXT6R SST has two sets of connection terminals,
located on opposite sides of the crossover board.
4. After making all connections, double-check that you
connected amplier “+” to speaker “+” and amplier “–”
to speaker “–”.
5. Make sure all the Roto-Lock toggle feet are retracted so
that they are tucked within the mounting hole’s border.
Figure 1: Connection Terminals
Figure 2: Roto-Lock Toggle Feet Retracted
Connection Terminals
NOTE: THE ROTO-LOCK SYSTEM CAN ACCOMMODATE A WALL
MATERIAL THICKNESS OF 1 1/4” (32MM) WITH THE TOGGLE
FOOT CAP REMOVED THE SYSTEM CAN ACCOMMODATE A WALL
MATERIAL THICKNESS OF 1 3/4” (44MM). TO REMOVE THE
CLAMP FEET, USE A SMALL SCREWDRIVER TO GENTLY RELEASE
THE LOCKING LEVERS (FIGURE 3, LEFT). THEN REMOVE THE FEET
FROM THE CLAMPS (FIGURE 3, RIGHT).
Figure 3: Removing the Roto-Lock Clamp Feet
VISUAL PERFORMANCE EXTREME SPEAKERS INSTRUCTION MANUAL
6. Insert the speaker into the mounting hole (Figure 4) and
tighten the four screws on the front of the speaker bae.
(Figure 5).
7. The Roto-Lock clamps will automatically rotate into
position and begin clamping the speaker.
8. The Visual Performance Extreme Grille features Sonance
Extreme Post Capture (XPC) technology. XPC holds the
grille in place by several small magnets located on the
posts of the grille and inside the post holes located on
the speaker bae (Figure 6). Place the grille against the
speaker, aligning the grille posts and post holes.
The magnets will pull the grille posts into the post holes
and hold the grille rmly in place. When the grille is
properly installed, the grille trim should make contact
with the mounting surface all the way around the speaker.
Figure 5: Tightening the Roto-Lock Screws
Figure 4: Inserting the Speaker into the Mounting Hole
Figure 6: Attaching the Grille
IMPORTANT: ALWAYS USE LOW-TORQUE SETTINGS WHEN USING A
SCREW GUN; NEVER OVER TIGHTEN.
NOTE: ADJUSTING THE TENSION OF THE ROTO-LOCK CLAMPS SO
THAT THE SPEAKER FRAME IS FLAT WILL HELP ENSURE THAT THE
GRILLE CONTACTS THE WALL ALL THE WAY AROUND THE SPEAKER
FOR A PROPER FIT.
NOTE: EXTREME POST CAPTURE TECHNOLOGY INVOLVES STRONG
MAGNETS THAT MAY CAUSE A FAST CONNECTION WHEN THE
GRILLE IS BEING INSTALLED ONTO THE SPEAKER. TAKE CAUTION
WHEN ALIGNING THE POSTS TO THE HOLES TO PROTECT FINGERS
FROM GETTING CAUGHT.
Roto-Lock
Screws
2
PAINTING THE GRILLES
Sonance Visual Performance Series speaker grilles
completely cover the exposed speaker frame, so only the
grilles (not the speakers themselves) require painting.
1. Prime the grille with a metal primer/bonder in a spray can.
Carefully follow the manufacturerʼs directions on the can.
2. We recommend using water-based latex paint on
the grilles. Thin the paint with a proper thinning agent
to a ratio of 1:1 paint-to-thinner, and strain it through a
standard mesh strainer to remove any lumps.
3. Use a small touch-up gun or cap-spray gun with a #3 tip
for painting.
(A) Set the nozzle with a medium to wide fan.
(B) Set the pressure regulator to 60psi.
(C) Lightly spray the front of the grille in 3 quick strokes
from approximately 10 inches away.
(D) Let the paint set for a minute, then turn the grille 90º
and lightly spray the grille again in 3 quick strokes.
Repeat this step until all four sides of the grille have
been evenly painted.
4. While the paint is still wet, inspect the grille and make
sure that excess paint has not collected underneath the
grille frame, and that none of the grille perforations are
lled with paint. If any are, use compressed air to blow
the paint out of the perforations.
5. Once the paint has thoroughly dried, mount the grille on
the speaker.
IMPORTANT: DUE TO ITS INCREASED DURABILITY, OIL-BASED
PAINT SHOULD BE CONSIDERED FOR VP EXTREME SERIES
SPEAKERS THAT ARE INSTALLED OUTDOORS.
IMPORTANT: IF YOU FIND ANY GRILLE PERFORATIONS THAT ARE
PLUGGED WITH PAINT AFTER THE PAINT HAS DRIED, USE A STRAIGHT
PIN OR SEWING NEEDLE TO CAREFULLY REMOVE THE PAINT.
©2018 Sonance. All rights reserved. Sonance and Visual Performance are registered trademarks of Dana Innovations. Due to continuous product improvement,
all features and specications are subject to change without notice. For the latest Sonance product specication information visit our website: www.sonance.com
SONANCE • 991 Calle Amanecer • San Clemente, CA 92673 USA • PHONE: (949) 492-7777 • FAX: (949) 361-5151 • Technical Support: (949) 492-7777 04.27.18
VISUAL PERFORMANCE EXTREME SPEAKERS INSTRUCTION MANUAL
LIMITED FIVE (5) YEAR WARRANTY
Sonance warrants to the rst end-user purchaser that this Sonance-brand product (“Product”), when purchased from an authorized Sonance Dealer/
Distributor, will be free from defective workmanship and materials for the period stated below. Sonance will at its option and expense during the warranty
period, either repair the defect or replace the Product with a new or remanufactured Product or a reasonable equivalent.
EXCLUSIONS
TO THE EXTENT PERMITTED BY LAW, THE WARRANTY SET FORTH ABOVE IS IN LIEU OF, AND EXCLUSIVE OF, ALL OTHER WARRANTIES,
EXPRESS OR IMPLIED, AND IS THE SOLE AND EXCLUSIVE WARRANTY PROVIDED BY SONANCE. ALL OTHER EXPRESS AND IMPLIED
WARRANTIES, INCLUDING THE IMPLIED WARRANTIES OF MERCHANTABILITY, IMPLIED WARRANTY OF FITNESS FOR USE, AND IMPLIED
WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE ARE SPECIFICALLY EXCLUDED.
No one is authorized to make or modify any warranties on behalf of Sonance. The warranty stated above is the sole and exclusive remedy and Sonance’s
performance shall constitute full and nal satisfaction of all obligations, liabilities and claims with respect to the Product.
IN ANY EVENT, SONANCE SHALL NOT BE LIABLE FOR CONSEQUENTIAL, INCIDENTAL, ECONOMIC, PROPERTY, BODILY INJURY, OR PERSONAL
INJURY DAMAGES ARISING FROM THE PRODUCT, ANY BREACH OF THIS WARRANTY OR OTHERWISE.
This warranty statement gives you specic legal rights, and you may have other rights which vary from state to state. Some states do not allow the exclusion
of implied warranties or limitations of remedies, so the above exclusions and limitations may not apply. If your state does not allow disclaimer of implied
warranties, the duration of such implied warranties is limited to period of Sonance’s express warranty.
Your Product Model and Description: VPXT6 or VPXT6R or VPXT6R SST or VPXT8R.
Warranty Period for this Product: Five (5) years from the date on the original sales receipt or invoice or other satisfactory proof of purchase.
Additional Limitations and Exclusions from Warranty Coverage: The warranty described above is non-transferable, applies only to the initial installation
of the Product, does not include installation of any repaired or replaced Product, does not include damage to allied or associated equipment which may
result for any reason from use with this Product, and does not include labor or parts caused by accident, disaster, negligence, improper installation, misuse
(e.g. overdriving the amplier or speaker, excessive heat, cold or humidity), or from service or repair which has not been authorized by Sonance. Obtaining
Authorized Service: To qualify for the warranty, you must contact your authorized Sonance Dealer/Installer or call Sonance Customer Service/Technical
Support at (949) 492-7777 within the warranty period, must obtain a return merchandise number (RMA), and must deliver the Product to Sonance shipping
prepaid during the warranty period, together with the original sales receipt, or invoice or other satisfactory proof of purchase.
3
VPXT6
Tweeter 1”(25mm)polyurethanedome,Ferrouidcooled,
 inacousticbackchamber
Woofer 61/2”(165mm)injection-moldedpolypropylene/
 graphitecone,withintegralSantoprene™surround
FrequencyResponse 45Hz-20kHz±3dB
Impedance 8ohmsnominal;6ohmsminimum
PowerHandling 5wattsminimum;125wattsmaximum
Sensitivity 89dBSPL(2.83V/1meter)
Environmental ConformstoMilitaryStandard810Gforhumidity,
 saltspray,temperature&UV,IP-66waterproofrating
EnvironmentTemp -30º-175ºF(-34ºC-79ºC)
SpeakerDepth 21/2”(64mm)
Dimensions 83/8”x121/4”(213mmx311mm)
Cut-OutDimensions 615/16”x103/4”(176mmx273mm)
GrilleMaterial Powder-coatedstainlesssteel
ShippingWeight 12lbs(5.4kg)pair
VPXT6R
Tweeter 1” (25mm) polyurethane dome,
 Ferrouidcooled,inacousticbackchamber
Woofer 61/2”(165mm)injection-moldedpolypropylene/
 graphitecone,withintegralSantoprene™surround
FrequencyResponse 45Hz-20kHz±3dB
Impedance 8ohmsnominal;6ohmsminimum
PowerHandling 5wattsminimum;125wattsmaximum
Sensitivity 89dBSPL(2.83V/1meter)
Environmental ConformstoMilitaryStandard810Gforhumidity,
 saltspray,temperature&UV,IP-66waterproofrating
EnvironmentTemp -30º-175ºF(-34ºC-79ºC)
SpeakerDepth 31/2”(89mm)
Dimensions 93/4”(248mm)
Cut-OutDimensions 81/4”(210mm)
GrilleMaterial Powder-coatedstainlesssteel
ShippingWeight 12lbs(5.4kg)pair
VPXT6R SST
Tweeter 1”(25mm)polyurethanedome,dualvoicecoil,
 Ferrouidcooled,inacousticbackchamber
Woofer 61/2”(165mm)injection-moldedpolypropylene/
 graphitecone,withintegralSantoprene™surround
FrequencyResponse 45Hz-20kHz±3dB
Impedance 8ohmsnominal;6ohmsminimum
PowerHandling 5wattsminimum;125wattsmaximum
Sensitivity 89dBSPL(2.83V/1meter)
Environmental ConformstoMilitaryStandard810Gforhumidity,
 saltspray,temperature&UV,IP-66waterproofrating
EnvironmentTemp -30º-175ºF(-34ºC-79ºC)
SpeakerDepth 31/2”(89mm)
Dimensions 93/4”(248mm)
Cut-OutDimensions 81/4”(210mm)
GrilleMaterial Powder-coatedstainlesssteel
ShippingWeight 4.5lbs(2.1kg)each
VPXT8R
Tweeter 1”(25mm)polyurethanedome,Ferrouidcooled,
 inacousticbackchamber
Woofer 8”(205mm)injection-moldedpolypropylene/
 graphitecone,withintegralSantoprene™surround
FrequencyResponse 40Hz-20kHz±3dB
Impedance 8ohmsnominal;6ohmsminimum
PowerHandling 5wattsminimum;130wattsmaximum
Sensitivity 90dBSPL(2.83V/1meter)
Environmental ConformstoMilitaryStandard810Gforhumidity,
 saltspray,temperature&UV,IP-66waterproofrating
EnvironmentTemp -30º-175ºF(-34ºC-79ºC)
SpeakerDepth 33/4”(95mm)
Dimensions 115/8”(295mm)
Cut-OutDimensions 101/8”(257mm)
GrilleMaterial Powder-coatedstainlesssteel
ShippingWeight 14lbs(6.35kg)pair

Produktspezifikationen

Marke: Sonance
Kategorie: Lautsprecher
Modell: Visual Performance Extreme VPXT6

Brauchst du Hilfe?

Wenn Sie Hilfe mit Sonance Visual Performance Extreme VPXT6 benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten


Bedienungsanleitung Lautsprecher Sonance

Sonance

Sonance Visual Performance VP65 SST Bedienungsanleitung

16 Oktober 2024
Sonance

Sonance Visual Performance VP87 Bedienungsanleitung

6 Oktober 2024
Sonance

Sonance Mariner MX66 Bedienungsanleitung

11 September 2024
Sonance

Sonance MAG06V3 Bedienungsanleitung

4 September 2024
Sonance

Sonance Garden SGS Subwoofer Bedienungsanleitung

13 August 2024
Sonance

Sonance Visual Performance VP61 Bedienungsanleitung

11 August 2024
Sonance

Sonance Patio SR 2-125 Bedienungsanleitung

7 August 2024
Sonance

Sonance Visual Performance VP83 Bedienungsanleitung

4 August 2024
Sonance

Sonance Rock RK63 Bedienungsanleitung

3 August 2024
Sonance

Sonance Mariner 54 SST Bedienungsanleitung

2 August 2024

Bedienungsanleitung Lautsprecher

Neueste Bedienungsanleitung für -Kategorien-

Bowers And Wilkins

Bowers And Wilkins CWM664 Bedienungsanleitung

16 Oktober 2024
Focal

Focal Chorus 826 V Bedienungsanleitung

16 Oktober 2024
KEF

KEF Ci200ER Bedienungsanleitung

16 Oktober 2024
Steren

Steren SPK-1100BL Bedienungsanleitung

16 Oktober 2024
Aiwa

Aiwa SP-A100 Bedienungsanleitung

16 Oktober 2024
Trust

Trust GXT 628 Bedienungsanleitung

15 Oktober 2024
Pyle

Pyle PBMSPG6 Bedienungsanleitung

15 Oktober 2024
Marshall

Marshall Tufton Bedienungsanleitung

15 Oktober 2024
Sunstech

Sunstech SPUBT780 Bedienungsanleitung

15 Oktober 2024
Sharp

Sharp PS-932 Bedienungsanleitung

15 Oktober 2024