SolarEdge HOTWTR-SENS-RW-S1 Bedienungsanleitung

SolarEdge Kessel & Heizkessel HOTWTR-SENS-RW-S1

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für SolarEdge HOTWTR-SENS-RW-S1 (3 Seiten) in der Kategorie Kessel & Heizkessel. Dieser Bedienungsanleitung war für 6 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Download PDF
Seite 1/3
T
T
T
TTe
e
e
eem
m
m
mmpe
pe
pe
peper
r
r
rrat
at
at
atatur
ur
ur
urure
e
e
ee S
S
S
S Se
e
e
eenso
nso
nso
nsonsor
r
r
rr
K
K
K
KKi
i
i
iit
t
t
tt
I
I
I
IInst
nst
nst
nstnstal
al
al
alall
l
l
llat
at
at
atati
i
i
iio
o
o
oon
n
n
nn
This document describes how to install a SolarEdge PT100 temperature sensor and connect it to the residential water heater and to
the SolarEdge Smart Energy Hot Water device.
The sensor allows you to measure the water temperature in the water heater. After installing the sensor, you will be able to view the
temperature using SolarEdge monitoring platform.
P
P
P
PPa
a
a
aack
ck
ck
ckcka
a
a
aage
ge
ge
gege C
C
C
C Con
on
on
onont
t
t
tte
e
e
een
n
n
nnt
t
t
tts
s
s
ss
PT100 sensor (15 cm long probe)
Sensor 3-wire cable (3m)
T Joint pipe fitting with NPT (USA)/ BSP (Europe &APAC) threaded bushing adapters
Installation guide
Figure 1: Sensor, cable and T-joint fitting (with bushing adapters)
In
In
In
InInst
st
st
ststa
a
a
aal
l
l
lll
l
l
lla
a
a
aat
t
t
tti
i
i
iion
on
on
onon G
G
G
G Gu
u
u
uui
i
i
iide
de
de
dedel
l
l
lli
i
i
iin
n
n
nnes
es
es
eses
Installation of the temperature sensor should be carried out by a certified personnel.
Connect the sensor to the hot water outlet pipe, at the upper part of the water heater. This way only a small amount of water
should be drained so that the water level is below the hot water pipe.
You can use a third-party 3-wire connection cable, up to 20 meters / 65ft in length.
Connect the T-joint at the hot water outlet pipe so the PT100 sensor can be directly connected to the tank.
The original safety temperature and pressure valve is not used for the installation of the temperature.
In
In
In
InInst
st
st
ststa
a
a
aal
l
l
lll
l
l
lli
i
i
iin
n
n
nng t
g t
g t
g tg th
h
h
hhe Se
e Se
e Se
e See Sen
n
n
nnso
so
so
sosor
r
r
rr
Figure 2
. illustrates the sensor connection.
Figure 2: Installing the Sensor
1. Use the pressure valve to drain water from the water tank, until the water level is below the hot water outlet pipe connection. This
will ensure that when the outlet hose is removed, water would not spill out.
2. Connect the T-joint fitting to the water tank (See
Figure 3
):
a. Install the two bushing adapters on the T-joint fitting.
b. Connect the hot water hose to the T-joint fitting openings (left and central openings) and tighten the adapters.
c. Connect the T-joint fitting to the water tank using the adapter that includes the external thread.
Temperature Sensor Kit Installation MAN-01-00596-1.4
1
1
1
11
Figure 3: T-joint fitting connection
3. Insert the sensor into the other T-joint fitting opening and tighten by screwing to the T-Joint fitting.
4. Connect the sensor cable to the sensor See
Figure 4
:
a. Open the sensor lid.
b. Insert the cable with the fork terminals through the cable opening.
c. Connect the wires to the terminals: Red wire to red terminal; Blue (or other color) wires to green (or other color) terminals.
d. Close the lid.
Figure 4: Sensor interfaces
5. Connect the other end of the sensor cable to the Smart Energy Hot Water device (See
Figure 5
):
a. Turn OFF:
The ON/OFF/Pswitch of the Smart Energy Hot Water device
The AC switch on the main distribution panel
b. Release the four cover screws of the Smart Energy Hot Water device and open the cover.
c. Insert the sensor cable end through the communication gland located at the bottom of the Smart Energy Hot Water.
d. Connect the three wires to the left temperature input terminal block (marked J3) Red wire to pin 1 (left-most); two blue wires
to pins 2 and 3.
NOTE
When using a third-party 2-wire temperature sensor, connect wires to pins 1 and 2. After that, connect pin 2
and pin 3 with a jumper (not supplied by SolarEdge).
Figure 5: Connecting the sensor cable to the Smart Energy Hot Water device
6. Verify that a jumper socket
is assembled
on J5 pin header. This will allow usage of the PT100 sensor connected to connector.J3
Make sure to use the correct pin header matching the connector (
Figure 5
):
Temperature Sensor Kit Installation MAN-01-00596-1.4
2
2
2
22 Installing the Sensor
J3 connector - pin header J5
J6 connector - pin header J4
Figure 6: Pin holders (jumper sockets removed)
7. Close the device cover.
Te
Te
Te
TeTec
c
c
cch
h
h
hhn
n
n
nni
i
i
iic
c
c
cca
a
a
aal
l
l
ll Spe
Spe
Spe
Spe Spec
c
c
cci
i
i
iifi
fi
fi
fific
c
c
cca
a
a
aat
t
t
tti
i
i
iion
on
on
onons
s
s
ss
Sensor type PT100 (100 Ohms @ 0°C) to IEC 751, Class B, 3/4 wire
Construction 6.0mm diameter stem in 316 stainless steel
Termination IP67 aluminium alloy weatherproof connection head with 4 wire connection block, M20 x 1.5mm cable entry
(gland included)
Process connection 1/2" NPT parallel (NA)
1/2" BSP parallel (Europe, APAC, Australia)
Probe temperature
range -148°F to +842°F (connection head @ 338°F) / -100°C to +450°C (connection head @ 170°C)
Probe diameter Ø6mm (1/4”)
Probe length 150mm 1/2"BSPP
Ordering information NA: HOTWTR-SENS-NA-S1
Europe, APAC, Australia: HOTWTR-SENS-RW-S1
Temperature Sensor Kit Installation MAN-01-00596-1.4
Temperature Sensor Kit Installation 3
3
3
33

Produktspezifikationen

Marke: SolarEdge
Kategorie: Kessel & Heizkessel
Modell: HOTWTR-SENS-RW-S1

Brauchst du Hilfe?

Wenn Sie Hilfe mit SolarEdge HOTWTR-SENS-RW-S1 benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten


Bedienungsanleitung Kessel & Heizkessel SolarEdge

SolarEdge

SolarEdge HOTWTR-SENS-RW-S1 Bedienungsanleitung

8 August 2024

Bedienungsanleitung Kessel & Heizkessel

Neueste Bedienungsanleitung für -Kategorien-

Sencor

Sencor SWK 7706GD Bedienungsanleitung

14 Oktober 2024
Hotpoint

Hotpoint HE30S01SAG Bedienungsanleitung

14 Oktober 2024
Tesy

Tesy ModEco Electronic 50 Bedienungsanleitung

11 Oktober 2024
Junkers

Junkers KBR 280-3 A Bedienungsanleitung

10 Oktober 2024
Ariston Thermo

Ariston Thermo MicroGenus HE 32 MFFI Bedienungsanleitung

7 Oktober 2024
Elco

Elco Vistron H 500 Bedienungsanleitung

5 Oktober 2024
Worcester

Worcester Greenstar 12i System Bedienungsanleitung

4 Oktober 2024
Nibe

Nibe MT-WH21-019-FS Bedienungsanleitung

4 Oktober 2024
GE

GE 20P06SAG Bedienungsanleitung

4 Oktober 2024
Haier

Haier ES 15V-SD Bedienungsanleitung

4 Oktober 2024