Snap Circuits Pro SC-500 Bedienungsanleitung

Snap Circuits Spielzeug Pro SC-500

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Snap Circuits Pro SC-500 (76 Seiten) in der Kategorie Spielzeug. Dieser Bedienungsanleitung war für 46 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Download PDF

Seite 1/76

any means; electronic, photocopying, or otherwise without written permission from the publisher.

REV-H Revised 2012

Patent #‘s: 7,144,255, 7,273,377, & other patents pending

Project 242

-1-

Table of Contents

Basic Troubleshooting 1

Parts List 2

About Your Snap Circuits®Parts 3

DO’s and DON’Ts of Building Circuits 4

Advanced Troubleshooting 5

Project Listings 6, 7

Projects 102 - 305 8 - 73

Other Fun Elenco®Products 74

1. Most circuit problems are due to incorrect assembly.

Always double-check that your circuit exactly

matches the drawing for it.

2. Be sure that parts with positive/negative markings are

positioned as per the drawing.

3. Be sure that all connections are securely snapped.

4. Try replacing the batteries.

5. If the motor spins but does not balance the fan, check

the black plastic piece with three prongs on the motor

shaft. Be sure that it is at the top of the shaft.

Elenco®is not responsible for parts damaged due to

incorrect wiring.

Basic Troubleshooting

Note: If you suspect you have damaged parts, you can

follow the Advanced Troubleshooting procedure on page 5

to determine which ones need replacing.

Review of How To Use It (See page 3 of the Projects 1-101 manual for more details.)

The Snap Circuits®kit uses building blocks with snaps

to build the dierent electrical and electronic circuits in

the projects. These blocks are in different colors and

have numbers on them so that you can easily identify

them. The circuit you will build is shown in color and

with numbers, identifying the blocks that you will use

and snap together to form a circuit.

Next to each part in every circuit drawing is a small

number in black. This tells you which level the

component is placed at. Place all parts on level 1 first,

then all of the parts on level 2, then all of the parts on

level 3, etc.

A large clear plastic base grid is included with this kit

to help keep the circuit block together. The base has

rows labeled A-G and columns labeled 1-10.

Install two (2) “AA” batteries (not included) in the

battery holder (B1). The 2.5V and 6V bulbs come

packaged separate from their sockets. Install the 2.5V

bulb in the L1 lamp socket, and the 6V bulb in the L2

lamp socket.

Place the fan on the motor (M1) whenever that part is

used, unless the project you are building says not to

use it.

Some circuits use the red and black jumper wires to

make unusual connections. Just clip them to the metal

snaps or as indicated.

Note: While building the projects, be careful not to

accidentally make a direct connection across the

battery holder (a “short circuit”), as this may damage

and/or quickly drain the batteries.

WARNING: SHOCK HAZARD -

Never connect Snap Circuits®to

the electrical outlets in your home

in any way!

WARNING FOR ALL PROJECTS WITH A SYMBOL

Moving parts. Do not touch the motor or fan during operation. Do not lean

over the motor. Do not launch the fan at people, animals, or objects. Eye

protection is recommended.

WARNING: CHOKING HAZARD -

Small parts.

Not for children under 3 years.

Batteries:

• Use only 1.5V AA type, alkaline batteries

(not included).

• Insert batteries with correct polarity.

• Non-rechargeable batteries should not

be recharged. Rechargeable batteries

should only be charged under adult

supervision, and should not be

recharged while in the product.

• Do not mix alkaline, standard (carbon-

zinc), or rechargeable (nickel-cadmium)

batteries.

• Do not mix old and new batteries.

• Remove batteries when they are used up.

• Do not short circuit the battery terminals.

• Never throw batteries in a fire or attempt

to open its outer casing.

• Batteries are harmful if swallowed, so

keep away from small children.

• Do not connect batteries or battery

holders in parallel.

!WARNING: Always check your wiring before

turning on a circuit. Never leave a circuit

unattended while the batteries are installed. Never

connect additional batteries or any other power

sources to your circuits. Discard any cracked or

broken parts.

Adult Supervision: Because children’s abilities

vary so much, even with age groups, adults should

exercise discretion as to which experiments are

suitable and safe (the instructions should enable

supervising adults to establish the experiment’s

suitability for the child). Make sure your child reads

and follows all of the relevant instructions and

safety procedures, and keeps them at hand for

reference.

This product is intended for use by adults and

children who have attained sufficient maturity to

read and follow directions and warnings.

Never modify your parts, as doing so may disable

important safety features in them, and could put

your child at risk of injury.

-2-

Qty. ID Qty. IDName Symbol Part # Name Symbol Part #

r31-Snap Wire 6SC01 r110 6SCC3μF Capacitor

r32-Snap Wire 6SC02 r1100 6SCC4μF Capacitor

r13-Snap Wire 6SC03 r1470 6SCC5μF Capacitor

r14-Snap Wire 6SC04 r11k Resistor 6SCR2Ω

r17-Snap Wire 6SC07 r15.1k Resistor 6SCR3Ω

r1Battery Holder - uses

2 1.5V type AA (not

Included)

6SCB1 r110k Resistor 6SCR4Ω

r1Antenna Coil 6SCA1 r1100k Resistor 6SCR5Ω

r1Green Light Emitting

Diode (LED) 6SCD2 r1High Frequency

Integrated Circuit 6SCU5

r16V Lamp 6SCL2 r1PNP Transistor 6SCQ1

r1Microphone 6SCX1 r1NPN Transistor 6SCQ2

r1Power Amplifier

Integrated Circuit 6SCU4 r1Adjustable Resistor 6SCRV

r10.02 6SCC1μF Capacitor r1Variable Capacitor 6SCCV

r10.1μF Capacitor 6SCC2 You may order additional / replacement parts at our

website: www.snapcircuits.net

Note: There are additional part lists in your other project manuals.

Important: If any parts are missing or damaged, DO NOT RETURN TO RETAILER. Call toll-free (800) 533-2441 or e-mail us at:

help@elenco.com. Customer Service • 150 Carpenter Ave. • Wheeling, IL 60090 U.S.A.

Parts List (Colors and styles may vary) Symbols and Numbers

Produktspezifikationen

Marke:	Snap Circuits
Kategorie:	Spielzeug
Modell:	Pro SC-500
Produkttyp:	Elektrisches Set
Produktfarbe:	Mehrfarbig
Akku-/Batterietyp:	AA
Energiequelle:	Akku
Betriebsanleitung:	Ja
Verpackungsart:	Box
Anzahl unterstützter Akkus/Batterien:	4
Empfohlenes Alter in Jahren (mind.):	8 Jahr(e)
Akkus/Batterien enthalten:	Nein
Vorgeschlagenes Geschlecht:	Junge/Mädchen
Anzahl Teile:	75 Stück(e)
Batterien erforderlich:	Ja
Themenwelt:	Strom
Mit Ton:	Ja
EU TSD Warnung:	Nicht für Kinder unter 36 Monaten geeignet
Auszeichnungen:	Bolzen