Skytech 3002 Bedienungsanleitung

Skytech Sonstige Klimatisierung 3002

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Skytech 3002 (10 Seiten) in der Kategorie Sonstige Klimatisierung. Dieser Bedienungsanleitung war für 21 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Download PDF

Seite 1/10

INSTALLATION AND OPERATING INSTRUCTIONS

IF YOU CANNOT READ OR UNDERSTAND THESE INSTALLATION INSTRUCTIONS DO NOT ATTEMPT

TO INSTALL OR OPERATE

Model: 3002

INTRODUCTION

This SKYTECH remote control system was developed to provide a safe, reliable, and user-friendly remote control system for gas

heating appliances. The system can be operated thermostatically or manually from the transmitter. The system operates on radio

frequencies (RF) within a 20-foot range using non-directional signals. The system operates one of 1,048,576 security codes that are

programmed into the transmitter at the factory; the remote receiver’s code must be matched to that of the transmitter prior to initial use.

Review COMMUNICATION SAFETY under theTRANSMITTER SECTION and THERMO SAFETY under the REMOTE RECEIVER

SECTION. These signal/temperature safety features shut down the appliance when a potentially unsafe condition exists.

REV. 4-19-12 Page 1

Skytech: 3002

The transmitter operates on (2) AAA-size 1.5V batteries. It is recommended that ALKALINE batteries always be used for

longer battery life and maximum operational performance. IMPORTANT: New or fully charged batteries are essential for

proper operation of the multi-function transmitter. Insert (2) AAA-size 1.5 V batteries into the battery compartment on the

back of the transmitter, positioning the (+) and (-) ends of the batteries as indicated on the casing. When the batteries are

inserted, gure #2 (with similar numbers) will display.

Fig. 1 Transmitter Front and Back Views

Note: If a LOW battery icon appears on the screen,

check the position of the batteries.

CAUTION: Due to the sensitive temperature-monitoring

components in the transmitter, it may be necessary to

allow the transmitter to stabilize to room temperature

before accurate room temperatures are displayed on

the screen. If the transmitter is activated from a

severe cold condition, it can take up to fteen minutes

for accurate temperature readings to appear.

1. BATTERY ICON - Symbol means battery power is low. Replace batteries within 2-weeks.

2. TIMER- Indicates time remaining before system shuts OFF, when timer-programmed; 9-hour maximum setting.

3. MODE- Indicates operation MODE of system. ON indicates the system is manually ON. OFF indicates the entire

system is turned OFF and THERMO indicates the system will automatically cycle ON/OFF, depending on the SET

temperature.

4. SET- Indicates desire SET room temperature for THERMO operation.

5. FLAME – Indicates burner/valve in ON position.

6. CLOCK – Indicates the current time in AM/PM

7. ROOM – Indicates CURRENT room temperature.

8. °F indicates degrees Fahrenheit (°C indicates degrees Celsius).

LCD DISPLAY FUNCTIONS

ROOM

SET

Fig. 2 LCD Display Functions

MODE

COVER CLOSED

MODE

TIMER

TIME

SET

SLIDE COVER

OPEN

AAA

BACK OF

TRANSMITTER

Skytech: 3002 REV. 4-19-12 Page 2

BASIC TRANSMITTER FUNCTIONS

To understand the operation of the transmitter, press and release the MODE button (Fig. 3) until the LCD screen reads

OFF in the display (Fig. 4).

Step 1: Press the MODE button one time to manually turn ON the appliance (Fig. 5).

Step 2: Press the MODE button a second time to put the to put the system in THERMO mode (Fig. 6).

Step 3: Press the MODE button a third time to turn the appliance back OFF again as show in (Fig. 4).

Fig. 4 OFF Mode

ROOM

SET

Fig. 5 Manual ON

ROOM

SET

Fig. 6 Thermo Mode

ROOM

SET

Slide down the lower section of the cover on the front of the transmitter to expose the “SET” buttons (Fig. 1). The slide

cover protects the SET buttons from being changed accidentally. Close the cover after completing the following settings/

programming.

Blinking numbers on the LCD display indicate the system is awaiting user input, such as using the UP and DOWN buttons

to program a new setting. If no change is made to ashing digits within 15-seconds, the system will complete the

procedure last programmed and reset the display to its normal state.

SETTING UP THE TRANSMITTER

SETTING THE CLOCK

1. Press and hold the TIMER/TIME button on the transmitter

for more than 2-seconds (Fig. 7). The hour digit(s) will begin

blinking (Fig. 8)..

2. Press the UP or DOWN button until the desired hour is

displayed in AM or PM.

3. After setting the desired hour, press and release the TIMER/

TIME button again to set the minutes; the minute digits will

begin blinking (Fig. 9)..

4. Press the UP or DOWN button until the desired minutes are

displayed.

5. Press and hold the TIMER/TIME button again for more than

2-seconds. The time digits will cease blinking, indicating the

clock has been successfully set. You may also press the

SET button on the transmitter to stop the time digits from

blinking and set the time.

ROOM

SET

ROOM

SET

Fig. 8 SettingHours Fig. 9 Setting Minutes

Fig. 3 Mode Button

MODE

Fig. 7 Timer/Time Button

MODE

TIMER

TIME

SET

Skytech: 3002 REV. 4-19-12 Page 3

The factory setting for temperature is ºF. To change this setting to ºC, rst press and hold

the UP and DOWN buttons on the transmitter at the same time (Fig. 10). Follow this same

procedure to change from ºC back to ºF. When changing between the ºF and ºC scales, the

temperature in the SET frame defaults to the lowest temperature (45º F, or 6º C). The

highest SET temperature is 99º Fahrenheit (32º Celsius).

SETTING ºF / ºC SCALE

The remote receiver operates on (4) AA-size 1.5V batteries.

It is recommended that ALKALINE batteries be used for

longer battery life and maximum microprocessor

performance. IMPORTANT: New or fully charged batteries

are essential for proper operation of the remote receiver.

The remote receiver houses the microprocessor that

responds to commands from the transmitter to control

system operation. It emits one beep when it receives an

ON or OFF command manually, but no beep when cycling

on and off automatically in THERMO mode. The remote

receiver has a 3-position slide switch (Fig. 11) for selecting

the ON/REMOTE/OFF mode of operation:

• With the slide switch in the ON position (toward the LEARN button), the system will remain ON until the slide

switch is placed in the OFF or REMOTE position.

• With the slide switch in the REMOTE position (centered), the system will only operate if the remote receiver

receives commands from the transmitter.

• With the slide switch in the OFF position (away from the LEARN button), the system is OFF.

• It is suggested that the slide switch be placed in the OFF position if you will be away from your home for an

extended period of time. If the remote receiver is mounted out of children’s reach, placing the slide switch in the

OFF position also functions as a safety “lock-out” by both turning the system off and rendering the remote receiver

inoperative.

REMOTE RECEIVER

REMOTE

OFF

LEARN

Requires 4-AA 1.5V

alkaline batteries

Learning

button

Remote Receiver

Battery cover slides on/off

Slide

Switch

REMOTE

OFF

Fig. 11 Remote Receiver

INSTALLATION PRECAUTIONS

This remote control system must be installed exactly as outlined in these instructions. Read all instructions completely

before attempting installation. Follow instructions carefully during installation. Any modications of the SKYTECH

remote control or any of its components will void the warranty and may could cause a re hazard.

Do not connect any gas valve or electronic module directly to 110-120VAC power. Consult gas appliance manufac-

turer’s instructions and wiring schematics for proper placement of all wires. All electronic modules are to be wired to

manufacturer’s specications.

The following wiring diagrams are for illustration purpose only. Follow instructions from manufacturer of gas valve and/

or electronic module for correct wiring procedures. Improper installation of electric components can cause damage to

electronic module, gas valve and remote receiver.

WARNING

Fig. 10 Temperature Scale

MODE

Produktspezifikationen

Marke:	Skytech
Kategorie:	Sonstige Klimatisierung
Modell:	3002

Brauchst du Hilfe?

Wenn Sie Hilfe mit Skytech 3002 benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten

Ihren Namen*

Deine E-Mail*

Schreiben Sie hier Ihre Frage

Bedienungsanleitung Sonstige Klimatisierung Skytech

Skytech 3002 Bedienungsanleitung

1 August 2024

Bedienungsanleitung Sonstige Klimatisierung

Neueste Bedienungsanleitung für -Kategorien-

Elco LOGON B SOL Zonneregelaar Bedienungsanleitung

5 Oktober 2024

Junkers Storacell PF 1000 solar Bedienungsanleitung

20 September 2024

Junkers Storacell SK 160 Bedienungsanleitung

19 September 2024

Elco LOGON SOL plus Zonneregelaar Bedienungsanleitung

18 September 2024

Ygnis TOTALECO TURBO Diversen klimaatbeheersing Bedienungsanleitung

14 September 2024

Oregon Scientific BA169 weer hub Bedienungsanleitung

27 August 2024

Riello BGK0.1 Bedienungsanleitung

27 August 2024

Premix XR-Serie Bedienungsanleitung

27 August 2024

Elektrobock RJ 402 Bedienungsanleitung

26 August 2024

Elektrobock RJ 401 Bedienungsanleitung

26 August 2024