Siig CE-MT0812-S1 Bedienungsanleitung
Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Siig CE-MT0812-S1 (8 Seiten) in der Kategorie Wandsteun. Dieser Bedienungsanleitung war für 9 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet
Seite 1/8
04-0541A
TV Size: 32" - 55”
Max load capacity: 121lbs/55kg
Wall distance: 0.43/11mm
Universal Mounting Pattern
Ultra-Thin LED/LCD TV Mount - 32" to 55"
IMPORTANT: If you don't understand the installation instructions, please consult an
installation specialist
Ultra-Thin LED/LCD TV Wall Mount
Material: 2.0mm Cold Rolled Steel Plate
Installation Instructions
1
Caution
A G
B H
C I
D J
E K
F L
(×4) M8×16 screw
(×4) M6×16 screw
(×4) M8×80 bolt
(×4) M5×35 screw (×4) Concrete anchor
(×4) M8×35 screw (x2) Sponge sticker
(×4) M6×35 screw (×4) M8 spacer
When mounting to a wall that contains wood studs, confirm dead center of the wood stud prior to installation, it is
recommended that the wood studs be a minimum of 16" apart.
It is recommended that two people perform the installation. Injury and/or damage can result from dropping or
mishandling the display.
INSTALLATION AND OPERATING INSTRUCTIONS
Do not install near heater, fireplace, air conditioning, in direct sunlight, or any other heat producing source.
Failure to do so may result in damage to the display and could increase the risk of fire.
The wall structure must be capable of supporting at least the maximum load capacity as indicated. If not, the
wall must be reinforced. Proper installation procedure by yourself or a qualified service technician, as outlined in
the installation instructions, must be adhered to. Failure to do so could result in serious personal injury.
Recommended mounting surfaces: wood stud and solid-flat concrete. If the mount is to be installed on any
surface other than wood studs or concrete, use suitable hardware (not included but commercially available).
Prior to the installation of this product, the installation instructions should be read and completely understood.
The installation instructions must be read to prevent personal injury and property damage. Keep these
installation instructions in an easily accessible location for future reference.
CAUTION: The maximum load capacity is 121 lbs. Use with products exceeding the maximum load capacity may
cause serious injury. See apparatus instructions.
Do not install on a structure that is prone to vibration, movement or chance of impact. Failure to do so could
result in damage to the display and/or damage to the mounting surface.
Hardware Kit
(×4) M5×16 screw (×4) M6 washer
(x4) M5 washer
2
1
2
3
4
5
3
4
5
7
8
a) Wood Stud Installation
You should mark two positions total.
Stud finder for drywall installation
NOTE: When mounting to wood studs, the two wood studs must be a minimum of 16" apart.
Use a high-quality electronic stud finder (commercially available) to locate dead center of two studs and mark
their locations with a pencil.
Step 1: Wall Plate Installation
1
2With the help of an assistant, and using a bubble level to ensure the wall plate is level, position the wall plate
against the wall in the desired mounting location.
Mark the right and the left positions of the small horizontal slots that are in alignment with the studs.
Tools Required
Phillips head screw driver
Tighten the bolt with the 1/2" socket or 1/2" open-end wrench by turning clockwise until tight.
For each location, insert bolt (I) into the wall.
Pre-drill a 3/16" hole to a depth of approximately 3" in the wall stud at each marked location.
Level
1/2" socket & socket wrench and/or 1/2" open-end wrench
Drill, 3/16" (5mm) drill bit for wood stud installation and 3/8" (10mm) masonry drill bit for concrete/brick installation
CAUTION: Do not release the wall plate until it is properly mounted and secured to the wall.
6Place the wall plate against the wall and line up the mounting slots with the drilled holes. Check the bubble level
to verify that the wall plate is level.
CAUTION: Do not over-tighten bolts - doing so may cause unnecessary damage to the wall.
3
Produktspezifikationen
Marke: | Siig |
Kategorie: | Wandsteun |
Modell: | CE-MT0812-S1 |
Brauchst du Hilfe?
Wenn Sie Hilfe mit Siig CE-MT0812-S1 benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten
Bedienungsanleitung Wandsteun Siig
1 September 2024
1 September 2024
1 September 2024
1 September 2024
1 September 2024
1 September 2024
1 September 2024
1 September 2024
Bedienungsanleitung Wandsteun
- Wandsteun Exibel
- Wandsteun Gembird
- Wandsteun Hama
- Wandsteun Manhattan
- Wandsteun Manta
- Wandsteun Nedis
- Wandsteun Philips
- Wandsteun SilverCrest
- Wandsteun Essentiel B
- Wandsteun Velleman
- Wandsteun IKEA
- Wandsteun Schwaiger
- Wandsteun König
- Wandsteun MarQuant
- Wandsteun Pyle
- Wandsteun Pioneer
- Wandsteun Meliconi
- Wandsteun One For All
- Wandsteun Vivanco
- Wandsteun Continental Edison
- Wandsteun GoGEN
- Wandsteun Garmin
- Wandsteun Goobay
- Wandsteun Tripp Lite
- Wandsteun Karma
- Wandsteun NEG
- Wandsteun Logik
- Wandsteun Techly
- Wandsteun CGV
- Wandsteun Titan
- Wandsteun Vogel's
- Wandsteun Champion
- Wandsteun Monacor
- Wandsteun Fellowes
- Wandsteun AG Neovo
- Wandsteun Sanus
- Wandsteun Barkan
- Wandsteun Erard
- Wandsteun NewStar
- Wandsteun Insignia
- Wandsteun Speaka
- Wandsteun Digitus
- Wandsteun BlueBuilt
- Wandsteun Deltaco
- Wandsteun Peerless-AV
- Wandsteun Duronic
- Wandsteun Onn
- Wandsteun Steren
- Wandsteun VCM
- Wandsteun Chief
- Wandsteun Best Buy
- Wandsteun Bauhn
- Wandsteun StarTech.com
- Wandsteun Mitsai
- Wandsteun Dahua Technology
- Wandsteun Kanto
- Wandsteun Bretford
- Wandsteun Calligaris .com
- Wandsteun V7
- Wandsteun Gravity
- Wandsteun Ultimate Support
- Wandsteun TooQ
- Wandsteun Crest
- Wandsteun Crimson
- Wandsteun MantelMount
- Wandsteun Mount-It!
- Wandsteun My Wall
- Wandsteun Ridem
Neueste Bedienungsanleitung für -Kategorien-
15 Oktober 2024
14 Oktober 2024
14 Oktober 2024
5 Oktober 2024
3 Oktober 2024
2 Oktober 2024
1 Oktober 2024
1 Oktober 2024
28 September 2024
24 September 2024