Shure A15BT Bedienungsanleitung


Lesen Sie kostenlos die đź“– deutsche Bedienungsanleitung fĂĽr Shure A15BT (4 Seiten) in der Kategorie Nicht kategorisiert. Dieser Bedienungsanleitung war fĂĽr 3 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Seite 1/4
Printed in U.S.A.
©2009 Shure Incorporated
27C1916 (Rev. 5)
The A15BT matches, bridges, or isolates balanced and unbalanced devices of different
impedances and levels.
Impedance: XLR socket (Female), 33,000Ω
XLR plug (Male), 7500Ω, easily converted to 600Ω.
Unbalancing: Either end can be unbalanced by connecting pins 1 and 3.
Voltage difference: From 33,000Ω to 7500Ω, 6.4 dB
From 33,000Ω to 600Ω, 17.4 dB.
MEDIUM-IMPEDANCE SELECTION
As supplied, the A15BT XLR plug is at 7500Ω. To convert to 600Ω, refer to Figure 1 and
proceed as follows:
Remove the three-pin plug element by turning the screw counterclock-wise and 1.
withdrawing the element from the case.
Remove the GREEN lead pin jack from pin 3, and insulate the jack and bare 2.
lead.
Remove the tape from the pin jack on the WHITE lead and push the jack î‚żrmly 3.
onto pin 3.
Replace the plug element in the housing and fasten the screw î‚żrmly in place 4.
(turn clockwise).
Model A15BT User Guide
BRIDGING TRANSFORMER
TYPICAL APPLICATIONS
To connect the 600 line output of a preampliî‚żer, mixer, or recorder to a high-level, high-
impedance, unbalanced (Aux) input:
Connect the 600Ω output to the 33,000Ω XLR socket of the A15BT. Unbalance the XLR plug
on the A15BT and convert it to 7500Ω or 600Ω to provide the proper level and best signal-
to-noise ratio. Connect the A15BT to the Aux input. In this conguration, the A15BT “bridges”
the 600Ω line output. Refer to the table on the back page for the maximum input level to the
A15BT.
To match a high-impedance microphone output to a medium-impedance (approximately
10,000 ) input on a reel-to-reel or cassette recorder: ΩUnbalance both ends of the A15BT.
Connect the microphone output to the 33,000Ω XLR socket. Connect the 7,500Ω XLR plug to
the recorder.
For an unbalanced Aux input to accept a balanced low-impedance output: Unbalance the
33,000Ω XLR socket on the A15BT and connect it to the Aux input. Convert the XLR plug to
7500Ω or 600Ω and connect it to the balanced low-impedance device.
When a balanced 600 line output is needed on a unit with an Aux output (such as the Shure
SCM268):
Unbalance the A15BT 33,000Ω XLR socket and connect it to the Aux output. The A15BT XLR
plug offers a balanced line output at both 600Ω (at about a –20 dBm level) and 7500Ω.
SPECIFICATIONS
Frequency Response
20 to 20,000 Hz (See Figure below)
TYPICAL FREQUENCY RESPONSE
Impedance
XLR Pin Connector (M): 7500Ω or 600Ω
XLR Socket Connector (F): 33,000Ω
Voltage Ratio 7500 Ω 600 Ω
Medium-impedance to
high-impedance: +6.4 dB +17.4 dB
High-impedance to
medium-impedance: –6.4 dB –17.4 dB
Driving Source Winding Being Maximum
Impedance (ohms) Driven (ohms) Level (Volts)
600 600 0.5
600 7,500 2.5
600 33,000 6.0
7,500 7,500 1.5
7,500 33,000 5.0
33,000 33,000 5.0
Case
Full magnetic shield, steel with gray enamel î‚żnish
Dimensions
19 mm (3/4 in.) diameter; 89 mm (3 1/2 in.) long
33K Ω
Ω
1
3
2600
1
3
2
Ω
7500
FEMALE
INSERT
MALE
INSERT
TRANSFORMER
BLACK
WHITE
BLACK
GREENRED
BLUE
GROUND
TERMINAL
SNAP
RING
GROUND
TERMINAL
YELLOW
CONNECTOR WIRING DIAGRAM


Produktspezifikationen

Marke: Shure
Kategorie: Nicht kategorisiert
Modell: A15BT

Brauchst du Hilfe?

Wenn Sie Hilfe mit Shure A15BT benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten




Bedienungsanleitung Nicht kategorisiert Shure

Bedienungsanleitung Nicht kategorisiert

Neueste Bedienungsanleitung fĂĽr -Kategorien-