Sharp XEA-206 Bedienungsanleitung

Sharp Kasten XEA-206

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Sharp XEA-206 (4 Seiten) in der Kategorie Kasten. Dieser Bedienungsanleitung war für 14 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Download PDF

Seite 1/4

XE-A206 Quick Start Guide

The following describes how to get the cash register ready for operate. Follow these steps before you use the cash register for the first time.

Before you set up the cash register, prepare three new alkaline batteries LR6 ("AA" size) which are necessary for memory backup. Find a stable and flat surface not subject to direct radiation, to place

the cash register.

English

1Initializing the Cash Register

To ensure the cash register operates properly, please use the following

procedure:

1. Make sure the power cord is unplugged and batteries are not

installed on the register.

2. Insert the manager (MA) key into the mode switch and turn it to the

REG position.

3. Insert the plug of the power cord into the AC outlet. The buzzer will

sound three times.

IMPORTANT: This operation must be performed without batteries installed.

4. The cash register has now been initialized.

The register display will show “0.00” with “ ”.

2Installing the Batteries

1. Push the printer cover forward and detach it.

2. Open the battery compartment cover next to the paper roll cradle.

3. Install three new alkaline batteries LR6 (“AA” size) as shown at the

right. (Batteries are not supplied with the cash register.) Make sure

that positive (+) and negative (–) poles of each battery are properly

oriented.

4. When the batteries are properly installed, “ ” on the display will

disappear. Close the battery compartment cover.

3Installing the Paper Roll (for receipt printing)

If you want to use a paper roll for journal printing, please refer to GETTING

STARTED section of the instruction manual.

1. Lift up the print roller release lever to unlock and open the print roller arm.

2. Set a paper roll in the paper roll cradle as illustrated right.

NOTE: When setting a new paper roll in the paper roll cradle, be sure to cut

the paper end behind the taped (or pasted) point in advance.

3. Feed the end of the paper along with the paper positioning guides

as illustrated at the right.

4. While holding down the paper, slowly close the print roller arm, and

push down the arm until you hear a click locking the arm.

Make sure you securely push down the center of the wing part of the

arm as illustrated at the right. The paper will be fed automatically.

5. Cut off the excess paper using the edge of the inner cover, and

replace the printer cover. Press the Fkey to make sure the paper

end comes out of the printer cover and clean paper appears.

NOTE: If the print roller arm is not securely locked, the unit will not print correctly.

If this problem occurs, open the arm, and close the arm as instructed

above.

REG

OPX/Z MGR

PGM

X1/Z1

X2/Z2

OFF

VOID

Print roller arm

Print roller release lever

To the printe

Incorrect

To the printe

Correct

Paper positioning

guides

4Basic Programming

Set the mode switch to the PGM position.

Setting the Date

Enter the date in 8 digits using the month-day-year format. Then press s.

Example: 02262010 s

Date (February 26, 2010)

Setting the Time

Enter the time in 4 digits (“hhmm” format) using the 24 hour system. Then press s.

Example: 1430 s

Time (2:30 p.m.)

Setting Tax Rates (%)

NOTE: If you are in an area that uses a tax table for tax calculation, please refer to the programming

section in the instruction manual.

Specify a tax rate (%) for calculation of tax on each taxable subtotal using the following

sequence:

s➔9➔@➔ Tax number (1 to 4)* ➔@➔Tax rate (0.0000% to 100.0000%) ➔@

➔ ➔Minimum taxable amount (0.01 to 999.99) s➔A

(Smallest amount for which tax must be collected.)

*Up to 4 types of tax are programmable.

Example1: Set state tax 6.25% with tax exempt as 12¢

s 9@ 1@ 6P25@ 12 s A

Tax 1 Tax rate Min. taxable (6.25%)

amount ($0.12)

Example2: Set state tax 4% with tax exempt as 0¢

s 9@ 1@ 4 s A

Tax 1 Tax rate (4%)

Other Programming

While the cash register is pre-programmed so it can be used with minimal set-up, it does provide

you optional features. For details, please refer to the instruction manual.

Initial settings:

Department 1 to 10: Taxable 1

Department 11 to 99: Non-taxable

REG

OPX/Z MGR

PGM

X1/Z1

X2/Z2

OFF

VOID

When an error occurs:

When an error occurs with an alarm sound, press lto clear the error. If you do not clear the error, press

Etwice.

The transaction will be finalized in subtotal void or cash sale.

(TCADH2556RCZZ) 1

Printed in China

5Now, you are ready!

Before Starting Entries

• Set the mode switch to the REG position.

Registration Example (when selling department items by cash)

1. Enter your clerk code. (By default, clerk code 1 is assigned.)

2. Enter the price for the first department item.

For example for 5.00, enter 5:, and press the appropriate

department key.

For department 17 to department 32, press Dfirst before

pressing the department key.

For department 33 and above, enter the department code

using numeric keys, and press d, then enter the price and

press dagain.

3. Repeat step 2 for all the department items.

4. Press sto display the amount due.

5. Enter the amount received from the customer. (You can omit

this step if the amount tendered is the same as the subtotal.)

6. Press A, and the change due is displayed (when the

amount received was not entered, total amount is displayed)

and the drawer is opened.

7. Tear off the receipt and give it to the customer with his or her

change.

8. Close the drawer.

REG

OPX/Z MGR

PGM

X1/Z1

X2/Z2

OFF

VOID

Clerk code

5:!

Price and dept. 1

825D"

Price and dept. 18

2:0

Amount tendered

How to download Customer Support Tool:

Customer Support Tool can be downloaded from the Sharp web site.

Please visit the Sharp web site: http://www.sharpusa.com/registersoftware

Produktspezifikationen

Marke:	Sharp
Kategorie:	Kasten
Modell:	XEA-206
Gewicht:	7394 g
AC Eingangsspannung:	120 V
Display:	LED
Abmessungen (BxTxH):	330.2 x 429.3 x 279.4 mm
Zweites Display:	Ja
Drucktechnologie:	Thermal Inkjet
Display-Ziffern:	24 Ziffern
Unterstützte Papierbreite:	57.5 mm
Speichertyp:	Flash ROM
Typ zweites Display:	LED
Displaynummern der Buchstaben:	10
Zahlungsarten:	Bargeld
Clerk Schloss:	Ja
Anzahl der clerks/Abteilungen:	99