Sharkoon Vibe-Fixer III 5.25" Bedienungsanleitung

Sharkoon Speicherleser Vibe-Fixer III 5.25"

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Sharkoon Vibe-Fixer III 5.25" (2 Seiten) in der Kategorie Speicherleser. Dieser Bedienungsanleitung war für 41 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Download PDF

Seite 1/2

Manual

www.sharkoon.com

HDD VIBE FIXER

1. Apply the cushion pads to the frame (fig. 1).

2. Slide the silicone covers over the 6 clamps of the

frame (fig. 2).

3. Fasten the rubber bands to the outer clamps of

the frame (fig. 3).

9. Fasten the last rubber band to the frame’s central

hook (fig. 7).

This is how the frame should finally look like (fig. 8).

10. Install the frame with the HDD into the computer

case. Secure it with the included screws.

Operating conditions:

Any hard disk of 3.5" width and 1" height can be

mounted and operated with the Vibe-Fixer. The

operation temperature should not exceed 50°

Celsius permanently. For short periods of time, up

to 70° Celsius are tolerable for the rubber bands.

Keep in mind that the aging process of the rubber is

accelerated by heat! The rubber bands must not be

exposed to daylight (UV light) for long periods of

time.

Transportation note:

Rough handling during transportation may cause

some displacement of the hard disk from its rubber

suspension. After transportation open the PC, check

and correct any possible displacement of the disk to

ensure perfect operation of the unit.

It is strongly recommended to check the rubber

bands prior to any movement/shipment of the

computer (see section "Maintenance").

Maintenance:

The rubber bands of the VIBE FIXER are subject to

an aging process. Therefore it is required that the

rubber bands’ condition is checked every 12-18

months and to replace them if needed. Take a very

close look at the spots where the rubber is bent the

most, at the hooks and at the edges of the hard disk.

If cracking shows up, any part of the rubber feels

tacky or if the surface of the rubber bands looks

distinctively whitish, do not use the unit until the

rubbers have been replaced. You can order /

purchase substitution rubber bands at

support@sharkoon.com.

4. Two silicone covers come with a lengthwise cut.

Slide these covers over both inner parts of the

rubber bands (fig. 4).

5. Fasten the two inner parts of the rubber bands

with the included cable tie. Take care to move the

cable tie over the silicone covers (fig. 4). Cut the

overlaying end of the cable tie with a pair of

scissors.

6. Place the frame on a flat surface in front of you.

7. Pull up the outer string of a rubber band and

carefully slide the HDD into the gap (the strings of

the rubber bands which are tied together by the

cable tie go underneath the HDD) (fig. 5).

Note:

Take care that the rubber bands will not be amaged

by the HDD or parts of it.

8. Slide the outer string of the second rubber band

over the HDD and center the drive between the

rubber bands (fig. 6).

Note:

The rubber bands of the frame are quite sensitive to

mechanical damage. Sharp edges of the hard disk

may cause small cuts in the rubber, which might go

unnoticed but could eventually lead to disruption of

the rubber. While inserting the hard disk into the

frame this risk is most present. Therefore any sharp

edges on the hard disk must be covered using

standard isolating tape.

Important:

Never pull or press the rubber bands directly onto

any electronics of the hard disk. It is harmless if the

rubber bands touch the electronics, yet force must

be avoided. Try to avoid placing rubber bands

directly across processor chips of the hard disk as

they might get hot.

Produktspezifikationen

Marke:	Sharkoon
Kategorie:	Speicherleser
Modell:	Vibe-Fixer III 5.25"
Produktfarbe:	Schwarz
Anzahl der unterstützten Speicherlaufwerke:	1
Unterstützte Speicherlaufwerk-Schnittstellen:	IDE/ATA