SentrySafe QAP1E Bedienungsanleitung
SentrySafe
Kluis
QAP1E
Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für SentrySafe QAP1E (17 Seiten) in der Kategorie Kluis. Dieser Bedienungsanleitung war für 8 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet
Seite 1/17
QAP1E
QAP1BE
Quick Access Pistol Safe
Owner’s Manual
2
Table of ContentsWarnings
WARNING
SentrySafe recommends that you do not store guns in this unit.loaded
NOTICE
YOUR SAFE IS ONLY PART OF YOUR TOTAL SECURITY PROTECTION.
SentrySafe recommends that you store your safe in a closet, office, basement, bedroom or any
other location that is convenient for you but out of direct line of sight from prying eyes.
The location of the safe does not affect the safe’s ability to protect your valuables inside.
This is a California-approved firearm safety device that meets the requirements of Penal Code
section 23655 and the regulations issued thereunder.
1 2 3 4
4
NOTE: Store code and keys in a secure location (other than in the safe).
NOTE: SentrySafe offers a secure on-line location for the entry and retrieval of your code.
Go to and register your safe. www.registermysafe.com
Insert key into keyhole and turn clockwise.
NOTE: Do not lock key inside safe – this is an override key and will
open the safe in the event that you have lost your code.
A Remove the battery pack cover.
B Pull out battery pack (keep battery pack connected
to wires).
C Insert four NEW AA alkaline batteries.
IMPORTANT
All safe models initially work with the factory code 1, 2, 3, 4, 1. It is therefore
important to re-program your safe with a new user code you have personally
selected to provide maximum security.
The Quick Access Pistol Safe comes with a built-in code.
Factory code 1, 2, 3, 4, 1.
Press any button once to bring the safe out of standby mode, then
enter the Factory Code 1, 2, 3, 4, 1.
The Green LED will light.
To Program an Electronic Code
A Find the Reset button located behind the battery pack.
B Press and hold the Reset button until the keypad flashes 3 times.
The LEDs remain on to indicate it is ready to accept a new user code.
C Enter a user code that is four, five or six digits long.
D A successful programming of the user code is indicated when the
LED light flashes green three times.
Programming Your Safe
Preparing your safe for first-time use
Programming your safe
Programming Your Safe
NOTE: Do not use rechargeable batteries or any other type of non-alkaline battery.
Do not mix old and new batteries. Do not mix alkaline and standard batteries.
A
Produktspezifikationen
Marke: | SentrySafe |
Kategorie: | Kluis |
Modell: | QAP1E |
Brauchst du Hilfe?
Wenn Sie Hilfe mit SentrySafe QAP1E benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten
Bedienungsanleitung Kluis SentrySafe
31 August 2024
31 August 2024
31 August 2024
31 August 2024
31 August 2024
31 August 2024
31 August 2024
31 August 2024
31 August 2024
31 August 2024
Bedienungsanleitung Kluis
- Kluis Thule
- Kluis Conrad
- Kluis Topcraft
- Kluis Dometic
- Kluis Olympia
- Kluis Yale
- Kluis Perel
- Kluis Burg Wächter
- Kluis Honeywell
- Kluis First Alert
- Kluis Master Lock
- Kluis Phoenix
- Kluis Rottner
- Kluis Salvus
- Kluis Juwel
- Kluis Toolland
- Kluis Kidde
- Kluis Royal Sovereign
- Kluis SereneLife
- Kluis Sygonix
- Kluis Fluke
- Kluis VARO
- Kluis Duralock
- Kluis FireKing
- Kluis Jewel
- Kluis Protector
- Kluis Sentry
- Kluis Sistec
- Kluis SMC
- Kluis Steren
- Kluis Technomax
- Kluis Avanti
- Kluis Olymp
- Kluis Challenge
- Kluis Suncast
- Kluis Kreator
- Kluis Barska
- Kluis CAWI
- Kluis Rottner Tresor
Neueste Bedienungsanleitung für -Kategorien-
18 September 2024
17 September 2024
15 September 2024
5 September 2024
3 September 2024
3 September 2024
3 September 2024
3 September 2024
3 September 2024
2 September 2024