Saturn ST-HC7386 Bedienungsanleitung

Saturn Schere ST-HC7386

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Saturn ST-HC7386 (20 Seiten) in der Kategorie Schere. Dieser Bedienungsanleitung war für 11 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Seite 1/20
1
ST-HC7386
HAIR CLIPPER
МАШИНКА ДЛЯ СТРИЖКИ
МАШИНКА ДЛЯ СТРИЖКИ
3
GB
HAIR CLIPPER
Dear Buyer!
We congratulate you on having
bought the device under trade
name “Saturn. We are sure that
our devices will become faithful
and reliable assistance in your
housekeeping.
Avoid extreme temperature
changes. Rapid temperature
change (e.g. when the unit is
moved from freezing temperature
to a warm room) may cause
condensation inside the unit and a
malfunction when it is switched
on. In this case leave the unit at
room temperature for at least 1.5
hours before switching it on.
If the unit has been in transit,
leave it indoors for at least 1.5
hours before starting operation.
READ ALL INSTRUCTIONS BEFORE
USING AND SAVE THESE
INSTRUCTIONS
BLADE ALIGNMENT
Your clippers were carefully
examined to ensure, that the blades
were oiled and aligned before leaving
our factory.
Blades must be realigned, if they
have been removed for cleaning or
replacement.
To realign the blades, simply
match the upper and bottom blades
teeth up, point for point.
(End of top blade teeth should be
approximately 1.2mm back from
bottom blade; compare your clipper
blades with the sketch).
If blade alignment is incorrect,
add a few drops of oil to the blades,
turn clipper on for a few moments,
turn off and unplug. Loosen screws
slightly and adjust. Tighten screws
after blade is aligned.
4
OIL
To maintain your clipper in peak
condition, the blades should be oiled
every few haircuts.
Do not use hair oil, grease, oil
mixed with kerosene or any solvent,
as the solvent will evaporate and leave
the thick oil, which may slow down the
blades motion.
BLADE LEVER
The lever is conveniently located
near your thumb (If you’re right-
handed), so it can easily be adjusted
while the clipper is in your hand.
The lever adds versatility to your
clipper by allowing you to gradually
change the closeness of your cut
without an attachment comb.
When the lever is in the
uppermost position, the blades will
give you the closest cut and leave the
hair very short. Pushing the lever
downward gradually increases the
cutting length.
In its lowest position, the lever
will leave the hair approximately the
same length as a No. 1 comb.
The lever will also extend the use
of your blades, since a different
cutting edge is used in each setting.
In addition, if extremely heavy
hair cutting has jammed the blades, it
will help you remove hair that has
become wedged between the two
blades without removing the blades.
While the clipper is running,
rapidly move the lever from “close
cut” to “longer cut” a couple of times.
Doing this each time after you have
finished using your clipper, will help to
keep the blades clear of cut hair. If
your clipper stops cutting and this
does not help, your cutting blades are
blunt. Replace them with new blades.
IMPORTANT SAFEGUARDS
When using electrical appliances,
especially when children are present,
basic safety precautions should always
be followed, including the following:
To reduce the risk of death or injury
from electric shock:
Unplug this appliance before
cleaning.
Do not place or store appliance,
where it can fall or be pulled into a tub
or sink.
Do not use, while bathing or in a
shower.
Do not place in or drop into water
or other liquid.
Do not reach for an appliance that
has fallen into water. Unplug
immediately.
To reduce the risk of burns,
electrocution, fire or injury to persons.
Use this appliance only for its
intended use, as described in this
manual. Do not use attachments, not
recommended by the manufacturer.
This appliance should never be
left unattended, when plugged in.
Close supervision is necessary,
when this appliance is used by, on or
near children or invalids.
Never operate this appliance, if it
has a damaged cord or plug, if it is not
working properly.
Keep the cord away from heated
surfaces.
Do not pull, twist or wrap line
cord around appliance.
Never drop or insert any object
into any opening on this appliance.
Before use, make certain blades
are aligned properly.
Do not place appliance on any
5
surface, while it is operating.
Do not use this appliance with a
damaged or broken comb nor with
teeth missing from the blades, as
injury may occur.
INSTRUCTIONS FOR HAIR
CUTTING
Before starting the hair cut:
1. Inspect the clipper, making sure
that it is free of oil between the
cutting blade teeth and turn the unit
on to distribute the oil and to make
sure it is running smoothly. Wipe off
any excess oil. This should be done
after each use. While using the unit,
untwist the cord from time to time to
avoid tangling.
2. Seat the person so their head is
approximately at your eye level. This
allows ease of visibility, while cutting
and a relaxed control of the unit.
3. Before cutting always first comb
the hair, so it is tangle free and as it is
naturally worn.
4. Place a towel around the neck and
shoulders of the person having the
haircut.
REMINDERS
Cut the hair in a relaxed and slow
manner. Use short strokes only to
work gradually over the entire head.
Always take off a little hair at a
time, you can always trim off
additional hair later.
As you work, comb the hair
frequently back into the style to which
you are cutting.
When cutting with this hair
clipper, it is better to leave the hair
dry, not wet. With the hair dry, it is
much easier to control the amount of
hair being cut.
BEGINNING THE HAIRCUT
Cutting hair requires practice, so it is
always better to leave the hair longer
for the first few haircuts, until you
become used to the length, to which
each attachment cuts the hair.
ATTACHMENT COMB (see main
diagram)
Attachment Comb No. 1 leaves
3mm hair length.
Attachment Comb No. 2 leaves
6mm hair length.
Attachment Comb No. 3 leaves
9mm hair length.
Attachment Comb No. 4 leaves
12mm hair length.
Each comb attachment is marked
accordingly on its outside middle
surface.
To attach a comb, hold it with
teeth showing, and slide it onto and
along the clipper blade, until the front
of the comb firmly rests against the
clipper blade.
To remove the comb, simply pull
the comb upward and away from the
clipper blade.
For even cutting, allow the comb
attachment / cutter to cut through the
hair. Do not force it through. Also
remember to comb the hair frequently
to remove trimmed hair and to check
for uneven strands.
STEP 1 - NAPE OF THE NECK
1. Attach comb attachment 3mm or
6mm.
2. Hold the clipper cutting edge
pointed up and begin the haircut,
starting at the centre of the head at
the base of the neck (see diagram 1).
3. Hold the clipper comfortably in
your hand and hold lightly against the
head with the comb teeth pointing
upward. Gradually and slowly lift the
clipper, working upwards and outwards
through the hair, trimming just a little
at a time.
4. As you cut, gradually lift the hair
clipper head towards you. Continue to
cut the back area from the bottom of
the neck upwards to the top of the
ears.
STEP 2 - BACK OFTHE HEAD
Change to the next longest comb
attachment 9mm or 12mm and cut
the back of the head (see diagram 2).


Produktspezifikationen

Marke: Saturn
Kategorie: Schere
Modell: ST-HC7386

Brauchst du Hilfe?

Wenn Sie Hilfe mit Saturn ST-HC7386 benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten