Sanus SF34 Bedienungsanleitung


Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Sanus SF34 (10 Seiten) in der Kategorie Nicht kategorisiert. Dieser Bedienungsanleitung war für 57 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Seite 1/10
Sanus Systems 2221 Hwy 36 West, Saint Paul, MN 55113 USA
Customer Service: (800) 359-5520 • (651) 484-7988 info@sanus.com
Customer Service Europe: + 31 40 2324700 europe.sanus@milestone.com
(6901-300165 <01>)
ESPAÑOL FRANÇAIS РУССКИЙ 中文
ENGLISH
International Instruction Manual For Steel Foundations®
SF22 and SF26
SF30 and SF34
ENGLISH
Page 2
Hardware List
(PHOTO 1)
A) isolation block - 2
B) 1-1/2" pan head bolt - 4
C) lock washer - 4
D) rubber isolation pad - 16
E) plastic foot - 8
F) 5/8" pan head bolt - 8
G) carpet spike - 8
H) machine nut - 16
I) allen key - 2
J) speaker stud - 8
K) 5/8" speaker bolts (2)
(For Boston Acoustics VRM series
and other bolt–mount speakers.)
L) cork damping washer - 4
M) wire guide - 4
N) atheadbolt-4
ab
c
d
eg
PHOTO 1
Important: This product uses two
different feet for each base. Before
installing, be sure to check that the
feet are mounted with the (1) foot
on the front left and rear right of
the base, (2) front right and rear
left. The designation (1) & (2) are
on the bottom of each foot.
h
k
i
j
l
m
n
f
ENGLISH
Page 3 * PLEASE READ THE NOTE ON PAGE OF THIS MANUAL!5
‘Take the time to find the right speaker locations for your
listening room.
1] Attach the plastic feet (e) to the corners of
the base with the small pan head bolts (f). Photo
2-Group two pillars with each base. Align the
holes in the base with the holes in the isolation
block (a). Bolt the pillars and the base together
with the isolation block between them using
the large pan head bolts (b) and lock washers
(c). Photo 3-Using the wire guide is optional.
2] Adhere the two inch self-adhesive damping washers (l) to the flush side of each
top plate. The damping washers will be set in between the top plate and the pillars.
(Optional: You may fill the pillars with sand or shot at this time.) Align the holes in
the top plate with corresponding holes in the top of each pillar. Bolt the pillars and
the top plate together using the flat head bolts (n). Photo 4-The wire guide (m) is
optional.
3] Both spiked feet (g) and rubber feet (d) are provided for your Steel Foundations
®.
The spiked feet are preferable in terms of performance. Thread a machine nut (h)
over the spiked feet and thread the ends of the spiked feet into the threaded inserts
in the corner feet. Adjust the spiked feet until the stand is level and then lock into
place by tightening the machine nut. Use of
the spiked feet is optional.* The rubber feet
are provided as an alternative.
4] Three forms of speaker mounts are pro-
vided, steel speaker studs (j), rubber pads (d)
and the new Foundation Mount™ (k) which
is discussed in the next section. To utilize the
steel speaker studs, thread them into the holes
in the corners of the top plates until the end Photo 3
Photo 2


Produktspezifikationen

Marke: Sanus
Kategorie: Nicht kategorisiert
Modell: SF34
Breite: 292.6 mm
Produktfarbe: Schwarz
Material: Stahl
Platzierung: Flur
Höhe (max): 863.6 mm
Befestigungstyp: Freistehend
Höchstgewichtskapazität: 15.87 kg
Verpackungsbreite: 800.1 mm
Verpackungstiefe: 381 mm
Verpackungshöhe: 101.6 mm
Paketgewicht: 16330 g
Verbessertes Kabelmanagement: Ja

Brauchst du Hilfe?

Wenn Sie Hilfe mit Sanus SF34 benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten




Bedienungsanleitung Nicht kategorisiert Sanus

Bedienungsanleitung Nicht kategorisiert

Neueste Bedienungsanleitung für -Kategorien-