Sanus NFCD Bedienungsanleitung


Lesen Sie kostenlos die đź“– deutsche Bedienungsanleitung fĂĽr Sanus NFCD (5 Seiten) in der Kategorie Nicht kategorisiert. Dieser Bedienungsanleitung war fĂĽr 22 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Seite 1/5
Assembly Instructions for Model: NFCD
Thank you for choosing a Sanus Systems Natural Media Tower. The Model
NFCD is designed to keep your collection clean and organized by storing up to
430 CDs or 230 DVDs, all in one convenient location.
If you do not understand these directions, please contact Sanus at 800.359.5520
or www.sanus.com. Check carefully to make sure that there are no missing or
defective parts. Our customer service representatives can quickly assist you
with assembly questions, and missing or damaged parts. Replacement parts
for products purchased through authorized dealers will be shipped directly to
you. Never use defective parts. Improper assembly may cause damage or
serious injury. Do not use this product for any purpose that is not explicitly
speciîšżed by Sanus Systems. Sanus Systems can not be liable for damage
or injury caused by incorrect assembly, or incorrect use. Please call Sanus
Systems before returning products to the point of purchase.
Required Tools: Rubber mallet or hammer, screwdrivers, phillips & regular
Supplied Parts List: (Not to Scale)
NFCD Top - A
Qty. 1
Glass Shelves - F
Qty. 14
NFCD Base - B
Qty. 1
Center Support - D
Qty. 1
Side Panels - E
Qty. 2
NFCD Foot - C
Qty. 4
Sanus Name Plate - G
Qty. 1
Sanus Systems 2221 Hwy 36 West, Saint Paul, MN 55113 02.28.06 (100028)
Customer Service: 800.359.5520. See complementary Sanus products at www.sanus.com
Supplied Hardware: (Full Size)
Step 1 - Attach Feet to NFCD Base
Insert a Machine Screw ( ) into each Foot ( ); then using the regular screwdriver, attach the Feet to the NFCD Base ( ). K C B
Diagram 1
Cam - H
Qty. 4
Cam Pin - I
Qty. 4
Plastic Dowel - J
Qty. 4
Wood Screw - L
Qty. 4
Machine Screw - K
Qty. 4
Shelf Pin - M
Qty. 56
B
K
C
C
C
C
K
K
K
Step 2 - Insert Cam Pins into Side Panels
There are two holes that are centered on each side of the Side Panels ( ), and 12” [304.3 mm] from each end. Using E
the phillips screwdriver, screw Cam Pins ( ) into the two holes of each Side Panel taking care not to over tighten the Cam I
Pins.
Diagram 2
E
I
E
Step 3 - Insert Cam into Center Support.
Place a Cam ( ) into each of the four holes in the Center Support ( )H D
NOTE: Each Cam has an arrow on it. Using a phillips screwdriver align each Cam so the arrow is pointing toward
the small hole on the edge of the Center Support (See Detail - A).
Diagram 3
Step 4 - Secure Side Panels to Center Support.
The Cam Pins ( ) installed in each Side Panel ( ) line up with the small holes in the edge of the Center Support ( ). The top I E F
of each Side Panel is smooth and the bottom has a notch routed in the inside edge.
Attach a Side Panel to each side of the Center Support and using a phillips screwdriver, rotate each Cam ( ) clockwise until H
tight (See Detail - B).
Diagram 4
D
Small Hole
Cam Hole
Cam - H
Small
Hole
Cam - H
Detail - A
Top
Smooth
Bottom
Notched
I
H
E
E
F
Detail -B


Produktspezifikationen

Marke: Sanus
Kategorie: Nicht kategorisiert
Modell: NFCD

Brauchst du Hilfe?

Wenn Sie Hilfe mit Sanus NFCD benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten




Bedienungsanleitung Nicht kategorisiert Sanus

Bedienungsanleitung Nicht kategorisiert

Neueste Bedienungsanleitung fĂĽr -Kategorien-