Samsung MXJ-YA1509K Bedienungsanleitung

Samsung Nicht kategorisiert MXJ-YA1509K

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Samsung MXJ-YA1509K (3 Seiten) in der Kategorie Nicht kategorisiert. Dieser Bedienungsanleitung war für 9 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Download PDF

Seite 1/3

INSTALLATION MANUAL

Please read ‘Safety Precautions’ described in the installation manual of the air conditioner.

• Check the following parts in the package.

• For further information of the piping material and size of the refrigerant pipes, refer to the installation

manual of the air conditioner.

Branch joints

• Condensate may occur on the heat insulation surface according to the atmosphere inside of the ceiling.

• If the inside of the ceiling has high temperature or humidity rate is more than 80%, please add proper

insulation to prevent water drops.

• The stopper area of the pipe or socket should be spread with a welding material. EX)

Requirement

±10°

or less

The

horizon

Reducer Header joint

Pipe

Adhesive insulation tape

Insulating the pipe

Insulating

header joint

Insulating after brazing the cap

Adhesive insulation tape

Insulator

Header joint

Cover the connected part and fasten the header joint using a cable tie.

Insulate the header joint and the brazed part and wrap the connected

part with an adhesive insulation tape to prevent it from dewing.

Installing the Header joint

1. Select the reducer fitted on the diameter of the pipe.

Reducer

Pipe

To indoor unit

Pipe

To outdoor unit

Reducer

Pipe

To indoor unit

Pipe

To outdoor unit

Brazed part Provided

3. Install the header joint horizontally.

±15°

or less

The horizon

±10°

or less

The horizon

±15°

or less

The

horizon

The horizon

Oil balancing joint & gas side of the outdoor unit

Use an insulation with the heat resisting temperature over 120°C.

Wrap the branch joint with an insulation of a thickness of at least 10mm as shown in the diagram.

Wrap the connected part between the Outdoor joint and the gas side of the outdoor unit to

prevent it from defrosting. Wrap the oil balancing joint and gas side pipe of the outdoor unit

wholly to prevent it from dewing.

øD

90°

100mm or more

Cut the insulation

at the proper angle.

Cut the insulation

at the proper angle.

Wrap here with plastic tape

Use EPDM insulation.

Pipe insulation

(Field supply)

90°

Pipe

Pipe insulation

(Field supply) Insulation

(Field supply)

2. Block the reducer that is not used by brazing the cap if the number of connected indoor

unit is fewer than header joint holes.

Blocked the hole of

header joint

In order

<Gas side><Liquid side> Blocked the hole of

header joint

In order

Provided

Brazed part

Pipe

Oil balancing joint

(Field supply)

To outdoor unit

To other oil balancing joint or outdoor unit

Pipe

To other oil balancing

joint or outdoor unit



When combining 2 units, connect the oil balancing

pipe directly between the outdoor units.

Oil balancing

pipe

Installing the Oil balancing joint

Note

Connect the header joint to the pipe by cutting the provided reducer properly.

10~15mm

or more

Installing the Outdoor joint



Use the attached reducer according to the selected pipe size.

Pipe

Reducer

Pipe

To other outdoor unit

To other outdoor joint or Y-joint of the main pipe

To other outdoor joint or outdoor unit

Pipe

Reducer

Pipe

To other outdoor unit

To other outdoor

joint or outdoor unit

To other outdoor joint or Y- joint of the main pipe

To other outdoor unit

To other outdoor

joint or outdoor unit



Use the attached reducer according to the selected pipe size.

Note

Connect the Outdoor joint to the pipe by cutting the outlet of the Outdoor joint or provided reducer properly.

10~15mm or more

The horizon

Y-joint

Reducer

Model

Name MXJ-YA1509K MXJ-YA2512L MXJ-YA2812K MXJ-YA2815K MXJ-YA3119K MXJ-YA3819K MXJ-YA4422K

Liquid side

Gas side

x 2 EA

1x 2 EA

x 2 EA

2x 2 EA

x 2 EA

1x 2 EA

x 1 EA

3x 1 EA

x 1 EA

x 2 EA

2x 2 EA

x 1 EA

3x 1 EA

x 1 EA

3x 1 EA

x 1 EA

x 2 EA

x 1 EA

1 2 3 4 5 6 7

Model name Total indoor unit’s capacities

MXJ-YA1509K 15.0 kW and below

MXJ-YA2512L Over 15.0~40.6 kW and below

MXJ-YA2812K Over 40.6~46.4 kW and below

MXJ-YA2815K Over 46.4~69.6 kW and below

MXJ-YA3119K Over 69.6~98.6 kW and below

MXJ-YA3819K Over 98.6~139.2 kW and below

MXJ-YA4422K Over 139.2 kW

Y-joint for (High pressure gas)HR

Reducer

1 2 3

Model

MXJ-YA1500K MXJ-YA2500K MXJ-YA3100K MXJ-YA3800K

x 2 EA

1x 1 EA

x 1 EA

Model name Total indoor unit’s capacities

MXJ-YA1500K 23.2 kW and below

MXJ-YA2500K Over 23.2~69.6 kW and below

MXJ-YA3100K Over 69.6~139.2 kW and below

MXJ-YA3800K Over 139.2 kW

Header joint

Model

Name MXJ-HA2512K MXJ-HA3115K MXJ-HA3819K

Liquid side

Gas side

x 4 EA

1x 1 EA

x 1 EA

2x 8 EA

1x 1 EA

x 1 EA

4x 1 EA

x 8 EA

x 4 EA

3x 1 EA

8x 2 EA

x 1 EA

5x 8 EA

3x 1 EA

6x 8 EA

Reducer

1 2 3 4 5 6

7a b c

Model name Total indoor unit’s

capacities

The maximum

quantity of connection

MXJ-HA2512K 46.4 kW and below 4

MXJ-HA3115K 69.6 kW and below 8

MXJ-HA3819K Over 69.6kW ~

139.2KW and below 8

Outdoor joint for (High pressure gas)HR

Model

MXJ-T3100 MXJ-T3800

x 1 EA

Reducer

1 2 3 4 5 6

Model name Total outdoor unit’s capacities

MXJ-T3100 Below 48 HP

MXJ-T3800 Above 50 HP

Installation of outdoor joints

Do not install the outdoor

joint in this direction.

Liquid pipeGas pipe

Oil balancing

pipe

High pressure gas pipe

Connecting Method

Installing the Y-joint

Insulating the branch joint

Y-joint & liquid side of the outdoor unit

Attach the insulation provided with a branch joint to the insulation supplied in the eld

without a gap. Wrap the connected part with an insulation (Field supply) of a thickness of at

least 10mm.

Use an insulation with the heat resisting temperature over 120°C.

Wrap the branch joint with an insulation of a thickness of at least 10mm.

When insulating in high humidity(higher than 30°C, 80%), wrap the supplied insulation with

more than 10mm of extra insulation such as Polyethylene Foam or other similar material.



Attach the adhesive insulation tape to the pipe

as shown in the picture after insulating the pipe.

Insulation tape

(Field supply)

Pipe insulation

(Field supply)

Pipe

Fix securely without any gap.

Pipe insulation

Provided

Fix securely

without any gap.

Pipe insulation

(Field supply)

Pipe insulation

(Field supply)

150mm Branch

Y-joint

A thickness of the insulation (Field supply)

should be at least 10mm.

(Field supply)

Connect the header joint in order respecting the number of the indoor unit.

Connet the indoor unit as the highest capacity comes first.

Install the Y-joint ‘horizontally’ or ‘vertically’.

- Use connection part of Y-joint or provided

reducer by cutting them in accordance with

diameter of connecting pipe.

- Make certain 10~15mm or more for reducer

which connected with pipe.

- Remove burr on cut part of reducer.

It is impossible to connect reducer with pipe,

if pipe is deformed or reducer is untrimmed.

10~15mm

or more

Keep a minimum distance of 500mm or more before

connecting a branch joint.

Maintain ±15° on

the horizon



Install the Y-joint within ±15° on

the horizon or on the vertical.

500mm

or more

Main pipe

To outdoor unit

Pipe

Front

Rear

Pipe

Reducer

To other branch

joints or indoor unit

Reducer

Do not insert the pipe deeply into the Y-joint.

( Do not insert more than 70mm.)

Connecting pipe Connecting pipe



Basic specification



When cutting the connection part

Outdoor joint

Model

Name MXJ-T3819 MXJ-T4422 MXJ-TA3819L MXJ-TA4422L

Liquid side

x 2 EA

1x 2 EA

Gas side

x 2 EA

x 1 EA

Model name Total outdoor unit’s capacities

MXJ-T3819 /MXJ-TA3819L Below 48 HP

MXJ-T4422 /MXJ-TA4422L Above 50 HP

Reducer

1 2 3 4 5

6 7

ID ø22.4

ID ø19.2

OD ø15.9

DB98-33821A-07

This marking on the product, accessories or literature indicates that the product and its

electronic accessories (e.g. charger, headset, USB cable) should not be disposed of with

other household waste.

For correct disposal of this product, please visit http://www.samsung.com/weee.pdf

安装手册

≤ ±10°

水平线

承口歧管接头

配管

分歧管接头

◆ 用电缆扎带扎紧分歧管接头并封住连接部位。

◆ 分歧管接头和焊接部位保温，用保温胶带缠绕连接

部位以防止结露。

安装室外机接头

安装歧管接头

1．选择与管道直径匹配的承口。

承口

配管

至室内机

配管

<气体侧>

至室外机

承口

配管

至室内机

配管

<液体侧>

至室外机

备置

铜焊部件

2．如果连接的室内机数量少于歧管连接孔时，用焊接堵头封住不使用的接口。

歧管接头孔堵塞

按顺序

<气体侧>

歧管接头孔堵塞

按顺序

<液体侧>

备置

铜部件

油平衡接头和室外机气体侧

◆ 使用可耐120 ℃以上高温的保温材料。

◆ 使用10 mm以上厚度的保温材料包缠分支管接头，如图所示。

◆ 包缠室外接头和室外机气侧之间的连接部件，以防止结霜。包缠油平衡接

头和这个室外机的气侧管路以防止结露。

3．水平安装分歧管接头。

≤

±15°

水平线

<液体侧>

水平线

安装油平衡接头

备注

适当切割提供的承口将歧管接头连接到配管上。

≥ 10-15 mm

≤

±15°

水平线

≤

±10°

水平线

<气体侧>

水平线

Y形接头

分歧管接头

歧管接头

HR户外接头(高压气体)

承口

户外接头

型号

名称 MXJ-YA1509K MXJ-YA2512L MXJ-YA2812K MXJ-YA2815K MXJ-YA3119K MXJ-YA3819K MXJ-YA4422K

液体侧

气体侧

x 2 个

1x 2 个

x 2 个

2x 2 个

x 2 个

1x 2 个

x 1 个

3x 1 个

x 1 个

x 2 个

2x 2 个

x 1 个

3x 1 个

x 1 个

3x 1 个

x 1 个

x 2 个

x 1 个

1 2 3 4 5 6 7

型号室内机总容量

MXJ-YA1509K < 15.0 kW

MXJ-YA2512L > 15.0~40.6 kW

MXJ-YA2812K > 40.6~46.4 kW

MXJ-YA2815K > 46.4~69.6 kW

MXJ-YA3119K > 69.6~98.6 kW

MXJ-YA3819K > 98.6~139.2 kW

MXJ-YA4422K > 139.2 kW

型号

名称 MXJ-HA2512K MXJ-HA3115K MXJ-HA3819K

液体侧

气体侧

x 4 个

1x 1 个

x 1 个

2x 8 个

1x 1 个

x 1 个

4x 1 个

x 8 个

承口

1 2 3 4 5 6

HR Y形接头(高压气体)

承口

1 2 3

型号

MXJ-YA1500K MXJ-YA2500K MXJ-YA3100K MXJ-YA3800K

x 2 个

1x 1 个

x 1 个

型号室内机总容量

MXJ-YA1500K < 23.2 kW

MXJ-YA2500K > 23.2~69.6 kW

MXJ-YA3100K > 69.6~139.2 kW

MXJ-YA3800K > 139.2 kW

型号

室内机总容量室内机总容量

MXJ-HA2512K < 46.4 kW 4

MXJ-HA3115K < 69.6 kW 8

MXJ-HA3819K < 69.6 kW ~

139.2 kW 8

牢牢固定，不留

间隙，配管保温

备置

配管保温

(现场备置)

管道保温

(现场备置)

150 mm

Y形接头

保温胶带(现场备置)

至少10 mm以上

(现场备置)

牢牢固定，

不留间隙。

分支接头保温

Y形接头和室外机液体侧接头保温

◆将随分支接头提供的保温材料安装到与现场备置的保温材料连接到一起，

不要留有间隙。至少要使用10 mm厚的保温材料(现场配置)保缠连接部件。

◆使用可耐120 ℃以上高温的保温材料。

分支接头保温厚度至少为10 mm。

◆当在高湿度（30 ℃，80 % 以上）下进行绝缘时，请再另外用 10 mm 的聚

乙烯泡沫或类似材料将随供的绝缘部分缠绕。

保温带(现场备置)

保温套(现场制作)

* 完成上述操作后，请用胶带

缠绕保温处。

配管

请仔细阅读空调器安装手册中“安全注意事项”的内容。

·请检查包装中的下列部件。

·管道的材料和冷媒管的尺寸请参照空调器安装手册。

øD

90°

≥ 100 mm

以适宜的角度切

割保温材料

以适宜的角度

切割保温材料

用塑胶带包缠配管使用 EDPM 泡沫保温材料

管道保温套 ( 现场备置 )

90°

管道保温套

( 现场备置 )

配管

保温套

( 现场备置 )

保温胶带

配管保温

歧管接头保温

焊接堵头后保温

保温胶带

隔热材料

配管

油平衡接头(现场备置)

至室外机

至其它油平衡接头或室外机

配管

至其它油平衡

接头或室外机

* 当并联两台机组时在室外机之间直接连

接油平衡接头。

油平衡管

室外接头安装

液体管

气体管

油平衡管

高压气体管

注切割室外接头的出口或提供的承口将室外接头，正确连接室外接头和配管。

≥10-15 mm

此方向不要安装

室外接头

* 在气体侧使用与所选管道尺寸相匹配的承口附件。

配管

承口

配管

至其它室外机

至其它室外接头或主管的 Y 形接头

<气体侧>

至其它室外接

头或室外机

至其它室外机

至其它室外接

头或室外机

<液体侧>

* 在液体侧使用与所选配管尺寸相匹配的承口附件。

配管

承口

配管

至其它室外机

至其它室外接头或主管的 Y 形接头

至其它室外接头或室外机

连接方法

安装Y形接头

“水平”或“垂直”安装Y形接头。

◆

请勿将配管过深的插入 Y 形接头。

( 请勿使插入深度超过 70 毫米。)

注意

<垂直连接>

<使用承口>

- 请根据连接配管的直径切割Y形接头

(岔管)的连接部分或者提供的承口

后使用。

- 确保连接配管的承口间隙为

10-15 mm以上。

- 去除切割承口截面上的毛刺。

如果配管变形或承口不整齐，

无法连接承口和配管。

≥10-15 mm

◆

在连接分支接头之前，保持最小

500mm 以上的距离。

注意

<水平连接>

以水平线为

基准保持 ±15°

* 在水平或垂直方向

±15°范围内安装 Y 形接头。

≥ 500 mm

主配管

至室外机

管道

前

后

配管

承口

至其它分支管或

室内机

承口

<插入连接管道深度>

连接管道连接管道

* 基本规格 * 切割连接部分时

型号

名称 MXJ-T3819 MXJ-T4422 MXJ-TA3819L MXJ-TA4422L

液体侧

x 2 个

1x 2 个

气体侧

x 2 个

x 1 个

型号室外机总容量

MXJ-T3819 /MXJ-TA3819L

< 48 HP

MXJ-T4422 /MXJ-TA4422L

> 50 HP

承口

1 2 3 4 5

6 7

型号

MXJ-T3100 MXJ-T3800

x 1 个

承口

1 2 3 4 5 6

型号室外机总容量

MXJ-T3100

< 48 HP

MXJ-T3800

> 50 HP

•根据天花板内的空气条件可能会出现绝缘材料表面结露现象。

•如果天花板内部存在高温或湿度大于 80 %，

应增加适当的绝缘以防止滴水。

•配管或承口的堵塞部分应与焊接材料相分离。

要求事项

EX)

◆

按照室内机的编号顺序连接分歧管接头。

◆

连接室内机，先连接容量高的室内机。

注意

x 4 EA

3x 1 EA

8x 2 EA

x 1 EA

5x 8 EA

3x 1 EA

6x 8 EA

7a b c

ID ø22.4

ID ø19.2

OD ø15.9

三星全球服务网

如果您对三星产品有任何咨询或建议，请联系三星客服中心

服务热线：400-610-5858

网址：https://www.samsung.com/cn

联系地址：北京市朝阳区利泽中园 101 号启明国际大厦 M 层

三星（中国）投资有限公司

邮编：100102

制造商：三星电子株式会社

原产地：韩国

销售商名称：三星（中国）投资有限公司

销售商地址：北京市朝阳区望京东园四区 2 号中航资本大厦 19F

Produktspezifikationen

Marke:	Samsung
Kategorie:	Nicht kategorisiert
Modell:	MXJ-YA1509K

Brauchst du Hilfe?

Wenn Sie Hilfe mit Samsung MXJ-YA1509K benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten

Ihren Namen*

Deine E-Mail*

Schreiben Sie hier Ihre Frage

Bedienungsanleitung Nicht kategorisiert Samsung

Samsung RH77J90407H Bedienungsanleitung

8 Oktober 2024

Samsung CS-21M20ML Bedienungsanleitung

7 Oktober 2024

Samsung HG65AJ690YK Bedienungsanleitung

4 Oktober 2024

Samsung CS-21A11MH Bedienungsanleitung

4 Oktober 2024

Samsung MR-EH01 Bedienungsanleitung

3 Oktober 2024

Samsung CS21A551ML Bedienungsanleitung

2 Oktober 2024

Samsung WMN8000SXT Bedienungsanleitung

29 September 2024

Samsung IAB 146 2K Bedienungsanleitung

28 September 2024

Samsung Guru 1200 Bedienungsanleitung

27 September 2024

Samsung NA64H3010CK Bedienungsanleitung

26 September 2024

Bedienungsanleitung Nicht kategorisiert

Neueste Bedienungsanleitung für -Kategorien-

DAS Audio AX-112-5 Bedienungsanleitung

16 Oktober 2024

Ferplast Ergocomfort Freetime Bedienungsanleitung

16 Oktober 2024

AEG MECK52 Bedienungsanleitung

16 Oktober 2024

Makita UR012G Bedienungsanleitung

16 Oktober 2024

Stihl HT 70 Bedienungsanleitung

16 Oktober 2024

Ernesto H14270 Bedienungsanleitung

16 Oktober 2024

IFM AC901S Bedienungsanleitung

16 Oktober 2024

Nedis RFPOM120FBK Bedienungsanleitung

16 Oktober 2024

AEG E9KLCS01 Bedienungsanleitung

16 Oktober 2024

ART ProChannel II Bedienungsanleitung

16 Oktober 2024