Ruckus Wireless ZoneFlex R310 Bedienungsanleitung

Ruckus Wireless Zugangspunkt ZoneFlex R310

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Ruckus Wireless ZoneFlex R310 (4 Seiten) in der Kategorie Zugangspunkt. Dieser Bedienungsanleitung war für 15 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Download PDF

Seite 1/4

Published 24 July 2015, Part Number 800-70972-001 Rev A

ZoneFlex R310 Access Point

Quick Setup Guide

This Quick Setup Guide provides step-by-step instructions on how to set up

your Ruckus Wireless ZoneFlex R310 access point. After completing the

steps in this guide, you will be able to place the access point at your site

and provide network access to wireless clients. The rest of this document

refers to the ZoneFlex R310 access point as an AP.

BEFORE YOU BEGIN

Before deploying your Ruckus Wireless device, please check the Ruckus

Wireless Web site for the latest software and release documentation.

• Release Notes and User Documents are available at

http://support.ruckuswireless.com/documents

• Software Upgrades are available at

http://support.ruckuswireless.com/software

• Open Source information is available at

http://support.ruckuswireless.com/open_source

T HIS GUIDE IN O LTHER ANGUAGES

•请从以下网站获得该指南的简体中文版

https://support.ruckuswireless.com

• Vous trouverez la version française de ce guide à l'adresse suivante

https://support.ruckuswireless.com

•このガイドの日本語版は https://support.ruckuswireless.com

でご覧ください

•이 가이드의 한국어 버전은 웹 사이트

(https://support.ruckuswireless.com

) 에서 확인하시기 바랍니

다

• Veja a versão em português (Brasil) deste guia em

https://support.ruckuswireless.com

• Puede ver la versión en español (América Latina) de esta guía en

https://support.ruckuswireless.com

Figure 1. ZoneFlex R310 AP

PACKAGE CONTENTS

• One ZoneFlex R310 access point

• Two mounting screws and plastic wall anchors

• One T8 5mm M2.5 Torx locking security screw

• One unit removal pin

• Regulatory flyer

• Product warranty statement

• Declaration of conformity, if required

• Ruckus Wireless AP Getting Started Guide

• This Quick Setup Guide

C ONFIGURING THE AP

•Step 1: Collecting the AP MAC Address

•Step 2: Collecting Setup Requirements, Hardware, and Tools

•Step 3: Connecting Your Computer to the AP

•Step 4: Preparing Your Computer for AP Setup

•Step 5: Logging Into the AP Web Interface

•Step 6: Customizing the Wireless Settings

•Step 7: Placing the AP at the Site

•Step 8: Verifying the Installation

Step 1: Collecting the AP MAC Address

• Write down the MAC address (12 alphanumeric digits) from the

outside of the AP.

Step 2: Collecting Setup Requirements, Hardware,

and Tools

• A computer with Ethernet adapter running Windows 7 or equivalent,

with Firefox or equivalent web browser.

• One Cat 5e (or better) Ethernet cable.

• T8 Torx screwdriver.

• An AC-to-12VDC power adapter (sold separately)

--OR--

an 802.3af-compliant Power over Ethernet (PoE) switch or PoE

injector.

Step 3: Connecting Your Computer to the AP

AAfter removing the AP from its package, place it next to your

computer.

BUsing an Ethernet cable, connect your computer’s network port to the

POE IN port on the AP.

CConnect the AC power adapter (sold separately) to the 12VDC AP

port, and plug the AC power adapter into a convenient and protected

AC power source.

Alternatively, connect the POE IN port to a PoE injector or PoE switch

for both power and network connectivity.

Figure 2. AP rear panel

DAfter bootup, verify that the PWR LED on the AP is a steady green.

Step 4: Preparing Your Computer for AP Setup

AOn your Windows 7 computer, configure your network adapter from

the Local Area Connection settings as follows:

• Start > Control Panel > Network and Sharing

Center > Change Adapter Settings

Note:

The minimum software revision for the AP is base image 100.x or

later, SmartZone 3.2 or later, or ZoneFlex 10.0 or later.

The rest of this document collectively refers to the SCG SZ, vSZ, ZD,

and other controllers as Ruckus Wireless controllers.

Important!

If the AP is to be managed by a Ruckus Wireless controller, then

follow the controller user documents to connect the AP to your local

network and configure it for initial operation. In that case, you may not

need to complete the following steps.

Note:

The following procedures assume that Windows 7 is the operating

system. Procedures for other operating systems are similar.

Published 24 July 2015, Part Number 800-70972-001 Rev A

BEdit the TCP/IPv4 address settings as follows:

• Local Area Connection > Properties > Internet

Protocol Version 4 (TCP/IPv4) > Properties

The Internet Protocol Version 4 (TCP/IPv4) Properties dialog box

appears.

CSelect Use the following IP address (if it is not already selected) and

then make the following entries:

• IP address: 192.168.0.22 (or any available address in the

192.168.0.x network, except 192.168.0.1, which is the default

used by the ZoneFlex R310 AP)

• Subnet mask: 255.255.255.0

• Leave the DNS server and Default gateway fields empty.

D OKClick to save your changes. Your changes are put into effect

immediately.

Step 5: Logging Into the AP Web Interface

As specified in Step 4: Preparing Your Computer for AP Setup, the

computer should be connected to your AP through the Ethernet port and

powered on, ready for setup.

AOn your computer, open a Web browser window.

BIn the browser, enter https://192.168.0.1 to connect to the AP.

CPress <Enter> to initiate the connection. When a security alert dialog

box appears, click OK/Yes to proceed.

DWhen the Ruckus Wireless Admin login page appears, enter the

following:

• Username: super

• Password: sp-admin

EClick Login.

Step 6: Customizing the Wireless Settings

AOn the AP Web interface menu, click Configuration >

Wireless > 5G or Configuration > Wireless > 2.4G. The

Configure > Wireless > Common options appear.

BVerify that the following options are active:

•Channel: SmartSelect

•Channel Width: 20 MHz, 40 MHz, or 80 MHz (default).

•Country Code: Select the country in which the AP will be

operating.

CClick Update Settings if you made any changes.

DClick any of the eight Wireless # (Wireless LAN Number) tabs at the

top of the page.

EIn Wireless Availability, click Enabled.

FDelete the text in the SSID field, and then type a name for your network

that will help your users identify the AP in their wireless network

connection application.

GClick Update Settings to save your changes.

HIf required, repeat Steps D-G for any other Wireless # (Wireless LAN

Number) interface that you want to enable.

IClick Logout to exit the Web interface.

JDisconnect the AP from the computer and from the current power

source, and then restore your computer to its original network

configuration.

Step 7: Placing the AP at the Site

AMove the AP to its permanent location (accessible to both AC or PoE

power and network connection).

BUse a Cat 5e (or better) Ethernet cable to connect your network (or PoE

injector or switch) to the POE IN port on the AP.

--OR--

If you are not using an 802.3af-compliant PoE switch or PoE injector,

then connect the AC power adapter to the AP, and then to a

convenient power source.

CVerify that the POE IN port LED is lit.

Step 8: Verifying the Installation

AUsing any wireless-enabled computer or mobile device, search for and

select the wireless network you previously configured.

BIf you can connect, open a browser and link to any public Web site.

Congratulations! Your wireless network is active and ready for use. If you

need to configure advanced wireless settings, such as enabling security,

refer to the Ruckus Wireless Indoor AP User Guide.

I NSTALLING THE AP

The AP can be mounted on a flat surface, on a drop-ceiling T-bar, or on a

pole or flat surface. Refer to the following sections:

•Mounting on a Flat Surface

•Removing the AP from Flat-Surface Mounting Screws

•Mounting the AP on a Drop-Ceiling T-Bar

•Removing the AP from a Drop-Ceiling T-Bar

•Mounting the AP on a Flat Surface or Pole Using the Optional

Secure Mounting Bracket

•Removing the AP from the Optional Secure Mounting Bracket

Mounting on a Flat Surface

The factory-supplied mounting screws and plastic wall anchors allow you

to attach the AP to a wall or ceiling.

AUse the Mounting Template on the last page of this guide to mark the

locations for two drill holes on the mounting surface.

BUse a 4.75mm (3/16”) drill bit to drill holes approximately 25mm (1”)

deep into the mounting surface.

CInsert the factory-supplied anchors (A in Figure 3) and mounting

screws (B) into the mounting surface, leaving approximately 6 mm

(1/4”) of the screw heads protruding from the surface.

Figure 3. Mounting the AP on a flat surface

DPlace the AP onto the mounting screws so that the screw heads enter

the keyholes on the AP enclosure (C), and gently press down on the AP

until the locking tab in the upper AP keyhole locks the AP onto the top

mounting screw.

Important!

Write down all of the currently active settings so you can restore your

computer to its current configuration when this procedure is

completed.

Note:

If you purchased the AP in the United States, then this value is fixed to

United States at the factory and is not user configurable. If you

purchased the AP outside the United States, then verify that the value

is set to your country or region. Selecting the correct country code

ensures that the AP uses only the radio channels allowed in your

country or region.

Published 24 July 2015, Part Number 800-70972-001 Rev A

Removing the AP from Flat-Surface Mounting

Screws

ATo remove the AP from the factory-supplied mounting screws, gently

press the unit removal pin (A in Figure 4) into the access hole on the

end of the AP to release the bracket locking tab in the upper keyhole.

Figure 4. Removing the AP from the screw heads

BPush the AP up and pull it away from the mounting screw heads.

Mounting the AP on a Drop-Ceiling T-Bar

AOrient the AP so that the T-bar is positioned between the T-bar clips

as shown in Figure 5, then rotate the AP until the third T-bar clip

catches the T-bar and the latch locks the T-bar in place (Figure 6).

Figure 5. Initial position

Figure 6. Final position

B(OPTIONAL, for added security.) Using a Torx T8 screwdriver, insert the

locking screw (A) into the hole near the latch to lock the AP in place.

Removing the AP from a Drop-Ceiling T-Bar

• To remove the AP, first remove the security screw, then depress the

latch while rotating the AP so that the T-bar clips disengage the T-bar.

Mounting the AP on a Flat Surface or Pole Using the

Optional Secure Mounting Bracket

The customer-ordered Ruckus Wireless secure mounting bracket kit

(ordering part number 902-0120-0000) includes a metal mounting bracket

and provides greater security when attaching the AP to flat surfaces (walls

and ceilings) and to poles.

• If you are mounting the AP on a flat surface, then you will also need an

electric drill with a 4.75mm (3/16”) drill bit, and the four No. 6 zinc

plated screws and plastic wall anchors included with the kit.

• If you are mounting the AP on a truss or pole, then you will also need

the two customer-supplied stainless steel pipe clamps.

Continue with the following:

AIf you are mounting the AP on a flat surface, then use the secure

mounting bracket as a template to mark the locations for four drill

holes on the mounting surface. There are four screw holes available on

the secure mounting bracket.

Fasten the bracket to the flat surface using four mounting screws and

plastic wall anchors and continue with Step C.

BIf you are mounting the AP on a pipe or pole, then feed the two

customer-supplied stainless steel clamps through the slots on the

secure mounting bracket. Use common hand tools to tighten the

clamps around the pipe or pole.

After the bracket is attached, continue with Step C.

Figure 7. Attaching the AP to the secure mounting bracket

CInsert the two studs on the secure mounting bracket (A) into the

keyholes on the bottom of the AP.

DSlide the AP toward the Ethernet port until the locking tab in the upper

AP keyhole locks the AP onto the top mounting bracket stud.

Produktspezifikationen

Marke:	Ruckus Wireless
Kategorie:	Zugangspunkt
Modell:	ZoneFlex R310

Brauchst du Hilfe?

Wenn Sie Hilfe mit Ruckus Wireless ZoneFlex R310 benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten

Ihren Namen*

Deine E-Mail*

Schreiben Sie hier Ihre Frage

Bedienungsanleitung Zugangspunkt Ruckus Wireless

Ruckus Wireless ZoneFlex 7372 Bedienungsanleitung

28 August 2024

Ruckus Wireless ZoneFlex 7025 Bedienungsanleitung

28 August 2024

Ruckus Wireless ZoneFlex T610 Bedienungsanleitung

28 August 2024

Ruckus Wireless ZoneFlex 2925 Bedienungsanleitung

28 August 2024

Ruckus Wireless ZoneFlex 2942 Bedienungsanleitung

28 August 2024

Ruckus Wireless T710 Bedienungsanleitung

28 August 2024

Ruckus Wireless ZoneFlex R700 Bedienungsanleitung

28 August 2024

Ruckus Wireless R710 Bedienungsanleitung

28 August 2024

Ruckus Wireless ZoneFlex R600 Bedienungsanleitung

28 August 2024

Ruckus Wireless ZoneFlex 7343 Bedienungsanleitung

28 August 2024

Bedienungsanleitung Zugangspunkt

Neueste Bedienungsanleitung für -Kategorien-

DrayTek VigorAP 920R Bedienungsanleitung

13 Oktober 2024

Cisco Aironet 3700P Bedienungsanleitung

11 Oktober 2024

Cisco Aironet 1815m Bedienungsanleitung

8 Oktober 2024

TP-Link Festa F65-Wall Bedienungsanleitung

4 Oktober 2024

Cisco AIR-CAP702I-I-K9 Bedienungsanleitung

4 Oktober 2024

EnGenius ENH200 Bedienungsanleitung

1 Oktober 2024

Mikrotik OmniTIK 5 PoE ac Bedienungsanleitung

1 Oktober 2024

Dell PowerConnect W-IAP3WNP Bedienungsanleitung

29 September 2024

Mikrotik Cube Lite60 Bedienungsanleitung

28 September 2024

D-Link DWL-1000AP+ Bedienungsanleitung

24 September 2024