Roland HT-RX01 Bedienungsanleitung

Roland AV extender HT-RX01

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Roland HT-RX01 (2 Seiten) in der Kategorie AV extender. Dieser Bedienungsanleitung war für 11 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Download PDF

Seite 1/2

Before using this unit, carefully read the sections entitled “USING THE UNIT SAFELY” and “IMPORTANT NOTES”

on back side. These sections provide important information concerning the proper operation of the unit.

Additionally, in order to feel assured that you have gained a good grasp of every feature of your new unit, read

Owner's Manual in its entirety. This manual should be saved and kept on hand as a convenient reference.

Owner’s Manual

RS-232 Connector (RS-232 Conversion Cable) Specications

D-sub 9-pin (male)

12345

6789

3.5mm miniature

phone plug

TXD

RXD

GND

Pin No. Signal

1 N.C.

2 RXD

3 TXD

4 N.C.

5 GND

6 N.C.

7 N.C.

8 N.C.

9 N.C.

Communication method Synchronous (asynchronous), full-duplex

Communication speed 9600 bps, 19200 bps, 38400 bps, 115200 bps

Parity none

Data length 8 bit

Stop bit 1 bit

Code set ASCII

Flow control none

Cable Wiring Diagram

When using the included RS-232 conversion cable, RXD, TXD, and GND are wired as shown below.

Unit end

(conversion cable end) Controller end

N.C. : 1 1 :

RXD : 2 2 : RXD

TXD : 3 3 : TXD

N.C. : 4 4 :

GND : 5 5 : GND

N.C. : 6 6 :

N.C. : 7 7 :

N.C. : 8 8 :

N.C. : 9 9 :

* When you want to extend the RS-232 conversion cable, use a straight cable.

Attaching the Ferrite Cores

1. Open an included ferrite core by spreading apart the tabs at two places.

2. Attach the ferrite core to an HDMI cable, LAN cable, or RS-232 conversion cable.

* Close the ferrite core by pressing down on each tab until it clicks into place.

Attach near the base of the plug at

the end that connects to the unit.

Connection Examples

* For a connection to the HDBaseT connector, use a Cat5e (Category 5e) or higher shielded LAN cable.

* *For a connection to the RS-232 connector, use the included RS-232 conversion cable.

HDMI INPUT

connector

RS-232

connector

RS-232-compatible

projector, etc.

RS-232-compatible

device (computer, etc.)

Displays,

projectors, etc.

Roland XS series device, etc.

HT-RX01

HDBaseT OUTPUT

connector

RS-232

connector

RS-232

connector

RS-232

connector

RS-232-compatible

device (computer, etc.)

Displays,

projectors, etc.

Roland V-40HD device, etc.

HT-RX01

HT-TX01

RS-232

connector

HDMI INPUT

connector

HDMI OUTPUT

connector

Panel Descriptions

HT-TX01 (Transmitter)

1 2 3 * These connectors are not used.

4 5 6

HT-RX01 (Receiver)

1 2 7 * These connectors are not used.

4 8 6

No. Name Explanation

1 Power indicator This lights up when power is supplied.

2 LINK indicator This lights up when the transmitter/receiver is correctly connected

3 HDMI INPUT connector The HDMI signal from the source device is input here.

4 AC adaptor connector This is for connecting the included AC adaptor.

No. Name Explanation

5 HDBaseT (TX) connector This is for connecting a receiver.

6 RS-232 connector This is for connecting a remote-control device (RS-232-compatible

computer, projector, or the like) using the included RS-232 conversion cable.

7 HDMI OUTPUT connector This outputs the HDMI signal to a display device.

8 HDBaseT (RX) connector This is for connecting a transmitter, Roland XS series unit, or other such

device.

Main FeaturesChecking the Included Items

• The unit

• AC adaptor, insertion plugs (3 types)

• RS-232 conversion cable (2 m)

• Ferrite core x 3

• Owner’s Manual (this document)

This unit is a transmitter/receiver for long-distance transmission of HDMI signals over up to 100 meters using a single LAN cable (Cat5e or higher).

• Support for 1080/59.94p (full HD) and 3D video

• Support for HDMI 1.4 and HDCP 2.0

• Support for RS-232 signals

Attaching an AC Adaptor Insertion Plug

1. Attach an included AC adaptor insertion plug to the AC adaptor.

* Attach the insertion plug for your country or region.

* Attach the insertion plug by pressing it in until it clicks into place.

* Be sure always to use the included AC adaptor with the unit.

To detach, pull out the insertion plug

while squeezing the left and right

sides of the lock section inward.

Main Specications

Input Formats 480/59.94i, 576/50i, 480/59.94p, 576/50p, 720/59.94p, 720/50p,

1080/59.94i, 1080/50i, 1080/59.94p, 1080/50p, 640 x 480, 800 x 600,

1024 x 768, 1280 x 768, 1280 x 1024, 1366 x 768, 1400 x 1050,

1600 x 1200, 1920 x 1200

* RGB formats : Conforms to VESA DMT Version 1.0 Revision 11.

* The maximum refresh rates of RGB is 75 Hz. (excluding 1600 x 1200

and 1920 x 1200. The refresh rate of these 2 is 60Hz)

* 1920 x 1200/60Hz : Reduced blanking

* Also check the supported resolutions of the connected device.

Audio Formats The maximum is PCM 8ch, Dolby Digital, True HD DTS-HD Master Audio

Input Connectors HT-TX01 HDMI x 1: Type A 19 pins

HT-RX01 RJ45 x 1

Output Connectors HT-TX01 RJ45 x 1

HT-RX01 HDMI x 1: Type A 19 pins

Other Connectors RS-232 x 1: 9 pins D-sub type * When using additional RS-232 cable.

Transmission distance The maximum is 100 m (328 ft)

* The available distance depends on the quality of the LAN cable.

Operating temperature range 0 to 40 degree C

32 to 104 degrees F

Operating temperature humidity 10 to 85 % (no condensation)

Storage temperature range -20 to 60 degree C

-4 to 140 degrees F

Storage temperature humidity 10 to 85 % (no condensation)

Power Supply AC Adaptor

Current Draw 2 A

Dimensions 81 (W) x 93 (D) x 24 (H) mm

3-3/16 (W) x 3-11/16 (D) x 1 (H) inches

Weight excl. AC adaptor 300 g

11 oz

* In the interest of product improvement, the specications and/or appearance of this unit are subject to

change without prior notice.

Dimensions

any form without the written permission of ROLAND CORPORATION.

For China

For EU Countries

*5100044591- 01*

24.9

73.4

WARNING

To completely turn o power to the unit, pull

out the plug from the outlet

Even with the power switch turned

o, this unit is not completely

separated from its main source

of power. When the power needs

to be completely turned o, turn o the

power switch on the unit, then pull out the

plug from the outlet. For this reason, the

outlet into which you choose to connect

the power cord’s plug should be one that is

within easy reach and readily accessible.

Do not disassemble or modify by yourself

Do not carry out anything unless

you are instructed to do so in the

owner’s manual. Otherwise, you

risk causing malfunction.

Do not repair or replace parts by yourself

Refer all servicing to your retailer,

the nearest Roland Service

Center, or an authorized Roland

distributor, as listed on the

“Information.”

Do not use or store in the following types of

locations

• Subject to temperature

extremes (e.g., direct sunlight

in an enclosed vehicle, near a

heating duct, on top of heat-

generating equipment); or are

• Damp (e.g., baths, washrooms,

on wet oors); or are

• Exposed to steam or smoke; or are

• Subject to salt exposure; or are

• Exposed to rain; or are

• Dusty or sandy; or are

• Subject to high levels of vibration and

shakiness.

Do not place in an unstable location

Otherwise, you risk injury as the

result of the unit toppling over or

dropping down.

Use only the supplied AC adaptor and the

correct voltage

Be sure to use only the AC adaptor

supplied with the unit. Also,

make sure the line voltage at the

installation matches the input voltage

specied on the AC adaptor’s body. Other

AC adaptors may use a dierent polarity, or

be designed for a dierent voltage, so their

use could result in damage, malfunction,

or electric shock.

Do not bend the power cord or place heavy

objects on it

Otherwise, re or electric shock

may result.

WARNING

Do not allow foreign objects or liquids to

enter unit; never place containers with liquid

on unit

Do not place containers containing

liquid (e.g., ower vases) on this

product. Never allow foreign

objects (e.g., ammable objects,

coins, wires) or liquids (e.g., water

or juice) to enter this product.

Doing so may cause short circuits,

faulty operation, or other malfunctions.

Turn o the unit if an abnormality or

malfunction occurs

Immediately turn the unit o,

remove the AC adaptor from the

outlet, and request servicing by

your retailer, the nearest Roland

Service Center, or an authorized Roland

distributor, as listed on the “Information”

when:

• The AC adaptor or the power cord has

been damaged; or

• If smoke or unusual odor occurs; or

• Objects have fallen into, or liquid has

been spilled onto the unit; or

• The unit has been exposed to rain (or

otherwise has become wet); or

• The unit does not appear to operate

normally or exhibits a marked change in

performance.

Be cautious to protect children from injury

Always make sure that an adult is

on hand to provide supervision

and guidance when using the

unit in places where children are

present, or when a child will be using the

unit.

Do not drop or subject to strong impact

Otherwise, you risk causing

damage or malfunction.

Do not share an outlet with an unreasonable

number of other devices

Otherwise, you risk overheating

or re.

Do not use overseas

Before using the unit in overseas,

consult with your retailer, the

nearest Roland Service Center, or

an authorized Roland distributor,

as listed on the “Information.”

CAUTION

Place in a well ventilated location

The unit and the AC adaptor

should be located so their location

or position does not interfere with

their proper ventilation.

CAUTION

When disconnecting the power cord, grasp it

by the plug

To prevent conductor damage,

always grasp the power cord by its

plug when disconnecting it from

this unit or from a power outlet.

Periodically clean the power plug

An accumulation of dust or foreign

objects between the power plug

and the power outlet can lead to

re or electric shock.

At regular intervals, be sure to pull out the

power plug, and using a dry cloth, wipe

away any dust or foreign objects that may

have accumulated.

Disconnect the power plug whenever the

unit will not be used for an extended period

of time

Fire may result in the unlikely event

that a breakdown occurs.

Route all power cords and cables in such a

way as to prevent them from getting

entangled

Injury could result if someone were

to trip on a cable and cause the

unit to fall or topple.

Avoid climbing on top of the unit, or placing

heavy objects on it

Otherwise, you risk injury as the

result of the unit toppling over or

dropping down.

Never connect/disconnect a power plug if

your hands are wet

Otherwise, you could receive an

electric shock.

Disconnect all cords/cables before moving

the unit

Before moving the unit, disconnect

the power plug from the outlet,

and pull out all cords from external

devices.

Before cleaning the unit, disconnect the

power plug from the outlet

If the power plug is not removed

from the outlet, you risk receiving

an electric shock.

Whenever there is a threat of lightning,

disconnect the power plug from the outlet

If the power plug is not removed

from the outlet, you risk receiving

an electric shock.

Keep small items out of the reach of children

To prevent accidental ingestion of

the parts listed below, always keep

them out of the reach of small

children.

• Included Parts: Ferrite core

IMPORTANT NOTES

USING THE UNIT SAFELY

Power Supply

• Do not connect this unit to same electrical

outlet that is being used by an electrical

appliance that is controlled by an inverter

or a motor (such as a refrigerator, washing

machine, microwave oven, or air conditioner).

Depending on the way in which the electrical

appliance is used, power supply noise

may cause this unit to malfunction or may

produce audible noise. If it is not practical

to use a separate electrical outlet, connect a

power supply noise lter between this unit

and the electrical outlet.

• The AC adaptor will begin to generate heat

after long hours of consecutive use. This is

normal, and is not a cause for concern.

• This unit is equipped with a protection

circuit. A brief interval (a few seconds)

after turning the unit on is required

before it will operate normally.

Placement

• This unit may interfere with radio and

television reception. Do not use this unit in

the vicinity of such receivers.

• Noise may be produced if wireless

communications devices, such as cell

phones, are operated in the vicinity of this

unit. Such noise could occur when receiving

or initiating a call, or while conversing.

Should you experience such problems, you

should relocate such wireless devices so

they are at a greater distance from this unit,

or switch them o.

• When moved from one location to

another where the temperature and/or

humidity is very dierent, water droplets

(condensation) may form inside the unit.

Damage or malfunction may result if you

attempt to use the unit in this condition.

Therefore, before using the unit, you must

allow it to stand for several hours, until the

condensation has completely evaporated.

• Do not place containers or anything else

containing liquid on top of this unit. Also,

whenever any liquid has been spilled on the

surface of this unit, be sure to promptly wipe

it away using a soft, dry cloth.

Additional Precautions

• Use a reasonable amount of care when

using its jacks and connectors. Rough

handling can lead to malfunctions.

• When disconnecting all cables, grasp the

connector itself—never pull on the cable.

This way you will avoid causing shorts, or

damage to the cable’s internal elements.

• When you need to transport the unit,

pack it in shock-absorbent material.

Transporting the unit without doing

so can cause it to become scratched or

damaged, and could lead to malfunction.

Copyrights/Licenses/Trademarks

• MMP (Moore Microprocessor Portfolio)

refers to a patent portfolio concerned

with microprocessor architecture, which

was developed by Technology Properties

Limited (TPL). Roland has licensed this

technology from the TPL Group.

• Roland is an either registered trademark

or trademark of Roland Corporation in the

United States and/or other countries.

• Company names and product names

appearing in this document are registered

trademarks or trademarks of their respective

owners.

Used for instructions intended to alert the

user to the risk of injury or material

damage should the unit be used

improperly.

* Material damage refers to damage or

other adverse effects caused with

respect to the home and all its

furnishings, as well to domestic animals

or pets.

Used for instructions intended to alert the

user to the risk of death or severe injury

should the unit be used improperly.

The symbol alerts the user to things that must be

carried out. The specific thing that must be done is

indicated by the design contained within the circle. In the

case of the symbol at left, it means that the power-cord

plug must be unplugged from the outlet.

The symbol alerts the user to important instructions or

warnings.The specific meaning of the symbol is

determined by the design contained within the triangle. In

the case of the symbol at left, it is used for general

cautions, warnings, or alerts to danger.

The symbol alerts the user to items that must never be

carried out (are forbidden). The specific thing that must

not be done is indicated by the design contained within

the circle. In the case of the symbol at left, it means that

the unit must never be disassembled.

About WARNING and CAUTION Notices About the Symbols

ALWAYS OBSERVE THE FOLLOWING

For the USA

FEDERAL COMMUNICATIONS COMMISSION

RADIO FREQUENCY INTERFERENCE STATEMENT

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the

FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential

installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in

accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee

that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or

television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the

interference by one or more of the following measures:

– Reorient or relocate the receiving antenna.

– Increase the separation between the equipment and receiver.

– Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

– Consult the dealer or an experienced radio/TV technician for help.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) this device may not cause harmful interference, and

(2) this device must accept any interference received, including interference that may cause undesired operation.

This equipment requires shielded interface cables in order to meet FCC class B limit.

Any unauthorized changes or modifications not expressly approved by the party responsible for compliance could void the user’s

authority to operate the equipment.

WARNING

This product contains chemicals known to cause cancer, birth defects and other reproductive harm, including lead.

For C.A. US (Proposition 65)

For Canada

CAN ICES-3 (B)/NMB-3 (B)

For Korea

Information

When you need repair service, call your nearest Roland Service Center or authorized Roland distributor in your country as shown below.

AFRICA

ALGERIA / ANGOLA / CABO VERDE

/ GUINEA / LIBYA /MOROCCO /

MOZANBIQUE /TUNISIA

Roland Iberia, S.L.

Paseo García Faria, 33-35

08005 Barcelona, SPAIN

TEL: +34 93 493 9136

SOUTH AFRICA

Paul Bothner(PTY) Ltd.

Royal Cape Park, Unit 24

Londonderry Road, Ottery 7800

Cape Town, SOUTH AFRICA

TEL: +27 21 799-4900

ASIA

CHINA

Roland China Limited

Shanghai Mart, Room 1507, No. 2299

Yanan Road West,

Changning District, Shanghai, 200336,

CHINA

TEL: +86-021-6236-6800

INDIA

Rivera Digitec (India)Pvt.Ltd

411, Nirman Kendra Mahalaxmi

Flats Compound o . Dr.Edwin

Moses Road, Mumbai-400011, INDIA

TEL: +91 22 2493 9051

INDONESIA

PT. Citra Intirama

Ruko Garden Shopping Arcade

Unit 8 CR, Podomoro City, JL.Let Jend.

S.Parman Kav.28, Jakarta Barat

11470, INDONESIA

TEL: +62 21 5698-5519

KOREA

KOREA AVICS CO., LTD.

Unit B-2208, Woolimblue9,

#240-21, Yeomchang-dong,

Gangseo-gu, Seoul, KOREA

TEL: +82 2-322-3264

MALAYSIA / SINGAPORE

Roland Asia Paci c Sdn. Bhd.

45-1, Block C2, Jalan PJU 1/39,

Dataran Prima, 47301 Petaling Jaya,

Selangor, MALAYSIA

TEL: +603-7805-3263

PHILIPPINES

EVI DISTRIBUTION PHILIPPINES, INC.

117. Sevilla Street , Brgy. Pedreo Cruz,

San Juan City 1210, PHILIPPINES

TEL: +632 774-5555

TAIWAN

ROLANDTAIWAN ENTERPRISE CO., LTD.

9F-5, No. 112 Chung Shan

North Road Sec. 2 Taipei 104, TAIWAN

R.O.C.

TEL: +886 2 2561 3339

VIET NAM

VIET THUONG CORPORATION

386 Cach Mang Thang Tam St.

Dist.3, Ho Chi Minh City, VIET NAM

TEL: +84-08-9316540

CENTRAL/SOUTH

AMERICA

BRAZIL

Roland Brasil Ltda.

Rua San Jose, 211

Parque Industrial San Jose

Cotia - Sao Paulo - SP, BRAZIL

TEL: +55 11 4615-5666

Other CENTRAL/

SOUTH AMERICA

Roland Corporation U.S.

5100S. Eastern Ave. Los Angeles,

California 90040, USA

TEL: +1 (323) 215-2111

EUROPE

AUSTRIA / GERMANY

Roland Germany GmbH

Adam-Opel-Strabe 4,

64569, Nauheim, GERMANY

TEL: +49 (0)6152-955 46 00

BELGIUM / FRANCE /

HOLLAND / LUXEMBOURG

Roland Center Europe NV

Houtstraat 3,

B-2260, Westerlo(Oevel), BELGIUM

TEL: +32(0) 14 57 58 11

CROATIA

ART-CENTAR

Degenova 3.

HR - 10000 Zagreb, CROATIA

TEL: +385 1 46 68 493

CZECH REP.

CZECH REPUBLIC DISTRIBUTOR s.r.o

Voctárova 247/16

180 00 Praha 8, CZECH REP

TEL: +420 283 020 270

DENMARK

Roland Scandinavia A/S

Skagerrakvej 7 Postbox 880

DK-2150 Nordhavn, DENMARK

TEL: +45 39 16 62 00

FINLAND

Roland Scandinavia As, Filial Finland

Vanha Nurmijarventie 62

01670 Vantaa, FINLAND

TEL: +358 9-6824020

GREECE

Bon Studio

6 Zaimi Street Exarhia

106 83 Athens, GREECE

TEL: +30 210 3809605

HUNGARY / ROMANIA

Roland East Europe Ltd.

2045. Torokbalint, FSD Park 3. ep.

HUNGARY

TEL: +36 (23) 511-011

ITALY

Roland Italy SpA

Viale dell industrie, 8

20020, Arese-Mi, ITALY

TEL: +39(0)2-937781

MALTA

Roland Iberia, S.L.

Paseo García Faria, 33-35

08005 Barcelona, SPAIN

TEL: +34 93 493 9136

NORWAY

Kontor NorgeRoland Scandinavia Avd.

Lilleakerveien 2 Postboks 95

Lilleaker N-0216 Oslo, NORWAY

TEL: +47 22 73 00 74

POLAND

ROLAND POLSKA SP. Z O.O.

ul. Kty Grodziskie 16B

03-289 Warszawa, POLAND

TEL: +48 22 678-95-12

PORTUGAL / SPAIN

Roland Iberia, S.L.

Paseo García Faria, 33-35

08005 Barcelona, SPAIN

TEL: +34 93 493 9136

RUSSIA

Roland Music LLC

Dorozhnaya ul.3,korp.6

117 545 Moscow, RUSSIA

TEL: +7 (495) 981-4967

SERBIA

Music AP Ltd.

Sutjeska br. 5 XS - 24413 Palic, SERBIA

TEL: +381-24-539-395

SLOVAKIA

DAN Distribution s.r.o

Povazská 18.

SK - 940 01 Nové Zámky, SLOVAKIA

TEL: +421 35 6424 330

SWEDEN

Roland Scandinavia A/S

SWEDISH SALES OFFICE

Mårbackagatan 31, 4 tr.

SE-123 43 Farsta, Sweden

TEL: +46 8-683 04 30

SWITZERLAND /

LIECHTENSTEIN

Roland (Switzerland) AG

Landstrasse 5, CH-4452 Itingen,

SWITZERLAND

TEL: +41 61 975 99 99

UKRAINE

EURHYTHMICS Ltd.

P.O.Box: 37-a.

Nedecey Str. 30

UA - 89600 Mukachevo, UKRAINE

TEL: +380 3131 414-40

IRELAND/

UNITED KINGDOM

Roland (U.K.) Ltd.

Atlantic Close, Swansea Enterprise Park,

Swansea

SA7 9FJ, UNITED KINGDOM

TEL: +44 1792 702701

OCEANIA

AUSTRALIA /

NEW ZEALAND

Roland Corporation

Australia Pty.,Ltd.

38 Campbell Avenue

Dee Why West, NSW 2099, AUSTRALIA

For Australia

TEL: +61 2 9982 8266

For New Zealand

TEL: +64 9 3098 715

MIDDLE EAST

BAHRAIN / KUWAIT / OMAN

QATAR / U.A.E

NMK Electronics

P.O.Box 3191 Sharjah, UAE

TEL: +971-4-2665244

CYPRUS / JORDAN / IRAQ

LEBANON / SYRIA /YEMEN

Roland Iberia, S.L.

Paseo García Faria, 33-35

08005 Barcelona, SPAIN

TEL: +34 93 493 9136

IRAN

MOCO INC.

Jadeh Makhsous karaj (K-9),

Nakhe Zarin AVE.

Jalal Street, Reza Alley NO.4

Tehran, 1389716791, IRAN

TEL: +98-21 44545370-5

ISRAEL

Halilit P. Greenspoon & Sons Ltd.

8 Retzif Ha’ alia Hashnia St.

Tel-Aviv-Yafo ISRAEL

TEL: +972-03-6823666

SAUDI ARABIA

Khaldi Est.

P.O. Box 3475 Abdul Malik Bin Marwan St

11471 Riyadh, SAUDI ARABIA

TEL: +966-1-219-5050

TURKEY

Atempo Ses ve Isik Sistemleri Ltd. Sti.

GUVENLIK SISTEMLERI LTD. STI.

AHL SERBEST BOLGESI A BLOK NO: 28 YE

34830 Istanbul, TURKEY

TEL: +90 212 288 0612

NORTH AMERICA

CANADA

Roland Canada Ltd. (Head O ce)

5480 Parkwood Way,

Richmond B. C., V6V 2M4, CANADA

TEL: +1 (604) 270 6626

Roland Canada Ltd. (Toronto O ce)

170 Admiral Boulevard

Mississauga ON L5T 2N6, CANADA

TEL: +1 (905) 362 9707

MEXICO

Roland Corporation U.S.

5100S. Eastern Ave. Los Angeles,

California 90040, USA

TEL: +1 (323) 215-2111

U. S. A.

Roland Corporation U.S.

5100S. Eastern Ave. Los Angeles,

California 90040, USA

TEL: +1 (323) 215-2111

As of Sep.1, 2014 (RSG)

For the USA

DECLARATION OF CONFORMITY

Compliance Information Statement

Model Name :

Type of Equipment :

Responsible Party :

Address :

Telephone :

HT-TX01 / HT-RX01

HDMI Extender

Roland Corporation U.S.

5100 S. Eastern Avenue Los Angeles,

CA 90040-2938

(323) 890-3700

Produktspezifikationen

Marke:	Roland
Kategorie:	AV extender
Modell:	HT-RX01

Brauchst du Hilfe?

Wenn Sie Hilfe mit Roland HT-RX01 benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten

Ihren Namen*

Deine E-Mail*

Schreiben Sie hier Ihre Frage

Bedienungsanleitung AV extender Roland

Roland HT-RX01 Bedienungsanleitung

6 August 2024

Bedienungsanleitung AV extender

Neueste Bedienungsanleitung für -Kategorien-

Tripp Lite B126-110 Bedienungsanleitung

7 Oktober 2024

LevelOne HVE-9211PR Bedienungsanleitung

2 Oktober 2024

LevelOne HVE-0201 Bedienungsanleitung

1 Oktober 2024

Tripp Lite B127F-1A1-SM-DD Bedienungsanleitung

30 September 2024

StarTech.com STUTPRXWAL Bedienungsanleitung

21 September 2024

StarTech.com STUTPTXWAL Bedienungsanleitung

21 September 2024

StarTech.com CPNTUTPWALLA Bedienungsanleitung

21 September 2024

StarTech.com STUTPWALL Bedienungsanleitung

21 September 2024

StarTech.com ST121UTPDVGB Bedienungsanleitung

21 September 2024

StarTech.com ST121RGB Bedienungsanleitung

21 September 2024